honda civic rocker arm torque spec

You search PDF repair manual about honda civic rocker arm torque spec, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda civic rocker arm torque spec Direct Download speed 5432 Kb/s

  honda civic rocker arm torque spec Full Version speed 8172 Kb/s



2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE MANUAL

0

Filed Under (Honda Manuals) by admin on 20-06-2012

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2 Fig. 16: Checking Continuity Between Rocker Arm Oil Pressure Switch 2P Connector Terminals Courtesy of AMERICAN HONDA MOTOR CO., INC. Is there continuity? YES- Go to step 9 . NO- Replace the rocker arm oil pressure switch (VTEC oil pressure switch) (see ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) REMOVAL/INSTALLATION ), then go to step 13 . 9. Turn the ignition switch ON (II). 10. Measure voltage between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminal No. 1 and body ground

Related Content:

solenoid 2007 honda, saturn ion shift handle micro switch, causes of low oil pump presure on 4l60e, serviceing cooling system for lincoln ls, replacing oil pressure switch on gmc sierra, injection actuation pressure sensor no c7 cat, location of oil pressure switch 2005 Honda cr-v, dt466e hard start no start diagnostics pdf, dt466 injection control pressure, chevrolet silverado oil pressure sensor repair

2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-12-2011

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, 02 ford explorer driveworks front wheel hub torque, torque number sway bar ends 2002 lincoln ls, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, lincoln ls 3 9l connecting rod bearing torque, idler arm torques, how many foot lbs torque on lower control arm bolt lincoln ls, ford e450 wheel torque, ford 4 0 sohc oil pan inserts torque specs

1999-2006 TOYOTA TUNDRA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the passenger sides of the vehicle. Next remove the wheels from both sides. 2. Using a 17mm socket, remove the lower sway bar link bolt from both sides. HINT: If the stud turns together with the nut use a hex wrench or vice grips to hold the stud . 4. Next remove the strut’s lower mounting bolt with a 19 mm socket and wrench. NOTE: Once the nut is removed, it may be necessary to use a punch and hammer to free the bolt. 5. Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 6. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the steel strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 7. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the steel spacer the strut will be rotated 180° when reinstalled. 8. Place strut back into upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 9. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. 10. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 11. Repeat Steps 3 through 10 on the opposite side of the vehicle. 12. Reattach the sway bar link assembly on both sides of the vehicle. Torque to OEM specs. For 2wd trucks skip Step 13. 13. For 4×4 models only it is necessary to lower the differential using the provided spacers and bolts. Install the spacers following the instructions provided with the spacers. 14. Reattach the wheels. Torque to OEM specs. 15. Lower vehicle to the ground and torque strut mounts to OEM specs. 16. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs 04 gmc yukon, torque specs 4 8 chevrolet, torque specs for 5 7 volvo penta exhaust manifold, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs

1984-2002 Pontiac Camaro / Firebird ADJUSTABLE TORQUE ARM INSTALLATION MANUAL

0

Filed Under (Pontiac Manuals) by admin on 23-02-2012

download
Inspect the motor mounts and the transmission mount. Worn, weak or broken mounts will cause the torque arm to not function properly and can cause damage to your vehicle. Stock OE transmission mounts in Camaros and Firebirds are very weak and known to fail. If you have a broken or weak transmission mount, it will cause the torque arm to actually lift the tail end of the trans. up. This could cause severe wheel hop, driveline misalignment and possible damage to the transmission, drive shaft, u-joints, rear axle, torque arm, and/or floor pan of vehicle. We highly recommend using a good quality polyurethane transmission mount like Energy Suspension #33- 1108. Using the Energy Suspension transmission mount is good insurance that your transmission stay solid and the torque arm will work to its full potential. 2. Inspect the rear suspension bushings. We strongly recommend using either Edelbrock (#5274) lower trailing arms with a spherical ball on one end and polyurethane bushings on the other, Edelbrock (#5204) trailing arms with polyurethane bushings on both ends, or other high quality trailing arms that use high quality polyurethane bushings. We also recommend the use of an Edelbrock or other high quality panhard rod to replace the stock OE piece that uses sponge rubber bushings. The lower trailing arms and panhard rod secure the rear axle under the car. Upgrading to stronger high quality tubular trailing arms and panhard rod with polyurethane bushings will increase the overall strength, eliminate the sponge feel of rubber bushings and further increase the function potential of the torque arm. Worn out trailing arm or panhard rod bushings can contribute to or cause torque arm or other suspension component failures. Remember each suspension component

Related Content:

2008 CHEVY UPLANDER TRAIL ARM BUSHINGS, how to change rear bushing in 06 chevy uplander, mistubishi fuso 4d34 idle linkage, torque on pitman arm 99 crown vic

1996-2004 TOYOTA TACOMA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 96-04 Tacoma 11/07 5. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the provided strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 6. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the provided spacer the strut will be rotated 180° when reinstalled. 7. Place strut back into the upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 8. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. HINT: It may be helpful to use a pry bar to press down on the steering knuckle for reinstalling the mounting bolt. 9. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 10. Repeat Steps 2 through 9 on the opposite side of the vehicle. 11. Reattach the wheels. Torque to OEM specs. 12. Lower vehicle to the ground and torque strut mounts to OEM specs. 13. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2013 TACOMA OEM SUBWOOFER, how to use oem ball joint press, OEM Ball Joint Press Instructions, 1996 Isuzu NPR Specs

FORD E450 CUTAWAY OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the front and rear bolts from the leaf spring. 2. Remove existing U-bolts and U-bolt plate that attach the axle to the leaf spring . Remove the leaf spring from the axle. 3. Remove the front spring hanger bracket , rear leaf spring hanger bracket, and any overload spring brackets . See Figure 2-1. These can be removed by grinding, or air chiseling, the heads off the factory-installed rivets, and using a hammer and punch to remove remainder of the rivet. See Figure 2-2. 3. Remove the OEM shock absorbers and retain the lower mounting fastener for later use. 4. Cut the exhaust as it bends downward after the axle, at its most vertical and straight section. See Figures 2-3 & 2-4. Save the cut-off portion for use in Section 9. Remove the rear exhaust hanger from the frame. CAUTION: Be careful that the leaf spring does not spring out of its hanger, or off the frame. FIG. 2-4 FIG. 2-1 FRONT HANGER BRACKET FIG. 2-2 LEAF SPRING REAR HANGER BRACKET FIG. 2-3 CUT HERE FOR EXHAUST MODIFICATION 6 3. DRIVER SIDE ASSEMBLY 1. Review Figure 3-1 & Figure 11-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using the (4) 7/16 x 1 1/4 UNC FLANGE BOLTS and (4) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . 3. Loosely secure the suspension Arm to the axle using (2) 5/8 UNF, 4.0 X 10.50 U-bolts, (4) 5/8 WASHERS, (4) 5/8 UNF HIGH NUTS, and the Arm Mount Plate. Make sure the locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. Note : Install the axle tube spacer between the U-bolts and Axle when installing on an E350. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the Arm to the Front Hangar using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Using the enclosed bolt hole template for the Upper Air Spring Mount, align the template to the frame using the appropriate rear spring hanger holes. Mark and drill three (3) new frame holes to 0.47″ on each side of the frame. Bolt the air spring bracket assembly to the frame using (5) 7/16 x 1 1/4 UNC CAPTIVE BOLTS and (5) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . Note : Use the correct holes designated for either the E350 or E450 chassis. See Figure 3-2. 6. Bolt the air spring to the suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut. (See Table 11-1 for appropriate Torque) . FIG. 3-2 E450 HOLE PATTERN E350 HOLE PATTERN TEMPLATE OE REAR HANGER MOUNT HOLES FRAME FIG. 3-1 AIR SPRING ARM MOUNT PLATE AXLE TUBE SPACER WEAR WASHER TRAILING ARM U-BOLT FRONT HANGER BRACKET AIR SPRING MOUNT BRACKET 7 AFTER BOTH SIDES HAVE BEEN INSTALLED (Sections 4, 5, 6) FINISH THE FOLLOWING STEPS: 7. Tighten the Arm bushing bolts and the Arm U-bolts AFTER the suspension has been installed and brought to Design Height, in Section 9.5. (See Table 11-1 for appropriate Torque) . 8. Install the new shock absorbers using the same orientation as factory, with factory and enclosed hardware. 9. IMPORTANT: Route the brake cable away from the air spring and any other moving components. It may need to be tied, or slightly repositioned in order to accommodate this. 4. PASSENGER SIDE DISASSEMBLY 1. Repeat Section 2 for the passenger’s side of the truck. 5. PASSENGER SIDE ASSEMBLY 1. Repeat Section 3 for the passenger’s side of the truck. Double-check all fasteners for proper torque. Check all clearance points and all alignments. See Figure 5-1 for details.

Related Content:

2002 rondevious change rear spring, f150 1995 changing front leaf spring brackets, head bolts torque on 2001 2 5 ford ranger, how to replace 2000 chevy cavalier exhaust bracket, how to replace mazda 3 rear coil springs, is there a metal washer before e clip on pitman arm seal gearbox on a 1997 ford f150, tie rod end at pitman armnut torque 2000 f350 7 3l 4wd, Trailing Arm bracket for 2000 Buick Century

1992 Cadillac Deville 4.9L Windshield Wiper Blade and Arm REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Cadillac Manuals) by admin on 22-05-2011

download
REMOVAL & INSTALLATION Catera Open the hood. 1. Remove the windshield wiper arm stud cap that conceals the nut. 2. Remove the windshield wiper arm nut. 3. Grasp the windshield wiper arm with both hands. 4. Use a rocking motion to loosen the windshield wiper arm from the pivots. 5. Remove the windshield wiper arm and blade. 6. To install: Installation is the reversal of the removal procedure. 7. Deville and Fleetwood WIPER ARM Raise the hood as needed for access to the wiper arms. 1. Operate the wipers and turn the ignition OFF when the wipers are at the mid-wipe position. 2. Lift the wiper arm from the windshield. 3. On 1990 vehicles, pull the retaining latch and remove the arm from the transmission shaft. 4. On 1991-93 vehicles, disengage the retaining latch using a suitable tool and remove the arm from the transmission shaft. 5. To install: Install the wiper arm onto the transmission shaft. 6. Push the retaining latch in and return the arm assembly to the windshield. 7. Park the wipers. If adjustment is necessary, proceed as follows: Remove the right wiper arm. a. Open the small door to access the wiper linkage; refer to the illustration for details. b.

Related Content:

1992 cadillac seville manual free download, how to remove wiper arm assembly chevy impala recalls, 1992 Cadillac Deville Owners Manual, 2007 chevy tahoe rear windshield wiper arm remove, cad 1992 seville horn low volume ?, how to replace a windshield wiper motor on a 2004 impala, remove wiper arm 04 ompala, video of how to install a windshield wiper arm on a rv

2007-2008 TOYOTA FJ CRUISER 2WD AND 4WD 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 12-11-2011

download
4Runner/FJ Cruiser Installation Instructions 08/28/08 INST-431.DOC Page 2 of 5 FRONT OF 4RUNNER/FJ CRUISER 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Before lifting vehicle, remove rear shock absorbers and discard. 5. Jack up the vehicle from the lift point in Figure A. 6. Support the vehicle with jack stands from the points in Figure A. 7. Remove the front wheels. 8. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 9. Remove front skid plate using 12mm socket. 10. Remove sway bar from frame using 14mm socket. See Figure C. 11. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 12. Remove cotter key and 19mm nut from outer tie rod end, rack & pinion utilizing a tie rod end puller (or pickle fork). 13. Remove the three nuts (14mm) from the top of the strut. See Figure D. 14. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 15. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft. 16. Release the compressor. 17. Remove the spring top plate from the strut. 18. Remove and discard the rubber spacer FRONT OF 4RUNNER/FJ CRUISER (continued) 19. Remove (hammer) the studs from the spring top plate. See Figure “F.” 20. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 21. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring and the Revtek Industries logo facing outward. See Figure H. 22. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Torque specs can be found on page 1.) 23. Install the TOP OUT EXTENDER over the STUDS (Figure H). 24. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 25. When properly installed, Revtek Industries logo will be centered between preload spacer reliefs. 26. Reinstall tie rod ends, torque to spec. 27. Reinstall sway bar to frame. 28. Reinstall sway bar end links into spindles. Torque to spec. 29. Reinstall front skid plate. 30. Replace the wheels; torque to spec.

Related Content:

Volvo D13 engine bolt torques, 2002 PT Cruiser jacking points, 92 toyota pinion nut torque spec, dtc molykote, how to remove torque converter bolts from a Volvo D13, removal of front struts Toyota FJ cruiser

EDELBROCK ROLLER ROCKER ARMS INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 21-02-2012

download
INSTALLATION: Rotate the main trunnion of the rocker arm so that the flat machined surface is facing up, then lower the rocker arm onto the rocker stud so that the roller tip is contacting the valve and the pushrod is seated into the cup. Rotate the engine by hand until cylinder #1 is at TDC on the compression stroke (the rotor on the distributor should be lined up with cylinder #1′s spark tower). If you are using hydraulic lifters, rotate the pushrod between your fingers as you tighten the rocker arm adjustment nut, once you start to feel drag in the pushrod you are at zero lash. Continue tightening the adjustment to set the lifter preload according to your camshaft installation instructions, then use an allen wrench to tighten the posi-lock. If you are using mechanical lifters, use a feeler gauge while tightening the adjustment nut to set your valve lash to the clearance listed in the camshaft installation instructions, then use an allen tool to tighten down the posi-lock. Complete this procedure for both the intake and exhaust rockers, then rotate the crankshaft 90° and repeat this procedure on the next cylinder in the firing order. Continue doing so until all 16 rocker arms have been properly installed and adjusted. Proper operation can be verified by rotating the crank by hand and observing the motion of the pushrod and the position of the roller on the valve tip. The pushrods must never contact the cylinder head walls and the roller tip must maintain at least 50% contact with the valve tip during a full rotation of the camshaft. If the pushrod contacts the cylinder head or the roller fails to maintain sufficient contact with the valve tip you will need to loosen your rocker stud and adjust your pushrod guideplate until proper valvetrain alignment is achieved.

Honda Clunk or Squeak From Rear Suspension Repair Manual

0

Filed Under (Honda Manuals) by admin on 15-02-2012

download
REPAIR PROCEDURE NOTE: ISIS online service manual information is only available for vehicles 1990 and newer. 1. Remove the rear trailing arm: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword REAR SUSPENSION, then select Suspension Arms Replacement from the list. 2. Mark the trailing arm at the arrow on the bottom of the bushing 3. Place the arm on a hydraulic press, supported by the hub base, with the spindle facing up. 4. With the hub driver, press the old bushing out of the trailing arm. 5. Install the new bushing with the short end toward the outside of the vehicle. Align the arrow with the mark you made on the trailing arm. 6. Press the new bushing into the trailing arm until its edge is 10 to 12 mm above the surface of the arm. 7. Reinstall the trailing arm. 8. If necessary, repeat steps 1 thru 7 to install a new bushing in the other rear trailing arm. 9. Bleed the brake system: •Refer to the brakes section of the appropriate service manual, or •Online, enter keyword BLEED, then select Brake System Bleeding from the list. 10. Check the wheel alignment, and adjust it if needed: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword WHEEL ALIGNMENT, then select Wheel Alignment – Rear Toe Inspection/Adjustment from the list

Related Content:

how 2002 install mountaineer rear trailing arm, removing rear torque arm on 97 buick century

Related Content:

solenoid 2007 honda, saturn ion shift handle micro switch, causes of low oil pump presure on 4l60e, serviceing cooling system for lincoln ls, replacing oil pressure switch on gmc sierra, injection actuation pressure sensor no c7 cat, location of oil pressure switch 2005 Honda cr-v, dt466e hard start no start diagnostics pdf, dt466 injection control pressure, chevrolet silverado oil pressure sensor repair