044e82 for fusion

You search PDF repair manual about 044e82 for fusion, if there are search results will appear below. If search results do not exist, please search by others keyword.



  044e82 for fusion Direct Download speed 5432 Kb/s

  044e82 for fusion Full Version speed 8172 Kb/s



VEHICLE WITH ALL 4 WHEELS ON THE GROUND, EXPANDED GUIDELINES TO PREVENT TRANSMISSION DAMAGE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 04-01-2012

download
FORD: MERCURY: 2010 Fusion 2010 Milan 2009-2010 Escape 2009-2010 Mariner SERVICE PROCEDURE 3. Do not flat tow the vehicle for greater than 6 hours at a time. There are specific instructions listed in the Owner Guide that must be followed to recreational tow/flat 4. Start and run the engine for: tow/tow a vehicle with all 4 tires on the ground. a. 5 minutes before towing each day Advise customers of the following expanded recreational towing guidelines. b. 5 minutes every 6 hours or less. 1. Transmission fluid level must be checked at c. While running the engine at idle for 5 operating temperature of 185 °F – 200 °F (85 minutes, with foot on the brake, shift °C – 93 °C), per Workshop Manual (WSM), through all gears. Section 307-01. At this temperature, adjust fluid These guidelines are designed to prevent damage level between minimum line and the minimum to the transmission due to overheating. hole at the bottom of the hash marks on dipstick. This level is within the safe operating If setting the fluid level for a customer that will be fluid level and does not require the customer to recreational (flat) towing the vehicle, set the level have the fluid level readjusted after flat tow between minimum line and the minimum hole at the operation. (Figure 1) bottom of the hash marks on dipstick (Figure 1) per WSM Section 307-01

Related Content:

2010 ranger srvice manual, ford service manual f-150 2010, 2010 ford fusion anttifreeze replacement, ford escape 2010 service manual

1994 Ford Mustang A/ C Evaporator Housing Removal and Installation

0

Filed Under (Ford Manuals) by admin on 03-06-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01 . If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side) . 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment.

Related Content:

acadia remove center console panel, remove center console 2002 pontiac grand prix, how to remove center console 2001 ford escort, howtoremovecenterconsolefrom2007malibu, how to tighten the overhead console laredo, 2000 corolla shift knob, how to take a part 2007 toyota tundra center console, how to replace center console lid on toyota tundra, HOW TO REMOVE THE CENTER CONSOL COVER ON A 2011 HONDA ACCORD, remove 2005 rav4 console

Related Content:

2010 ranger srvice manual, ford service manual f-150 2010, 2010 ford fusion anttifreeze replacement, ford escape 2010 service manual