Skip to content

05 dodge dakota door lock relay location

You search PDF repair manual about 05 dodge dakota door lock relay location, if there are search results will appear below. If search results do not exist, please search by others keyword.

1995 Volvo 850 L5-2.3L Turbo Relay Identification and Location

download
Relay Identification and Location Relays Inside the Central Electrical Unit 101-102Control module, cruise control (4/3) 103 Fuel pump relay (2/23) 104,108Main headlight relay with bulb malfunction indicator (2/1) 105 Overload relay +X supply (2/30) 106 Overload relay +15 supply (2/31) 107 Overload relay +X supply (2/60) 201 Fog light relay (2/2) 202 Relay, deadlock setting (2/47) 203 Relay, windshield intermittent wiper (2/4) 204 Relay, tailgate intermittent wiper (2/16) 205-206Relay, central lock and delayed inside lighting (2/7) 207 Speed warning (2/51) or exhaust temp. sensor relay (2/15) 208 Relay, heated rear window and door mirrors (2/44) 210-211Relay, anti-theft alarm (2/28) 212 Relay, seat belt reminder/key warning (2/5) 213 Front fog lights, bridge (25/9) 214 Relay, heated rear seat (2/43) If the car is not equipped with a theft alarm, position 210 is bridged and 211 is unconnected. Relays Outside the Central Electrical Unit

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

1998 Volvo S70 T5 L5-2.3L Turbo Fuse/ Relay Identification and Location Manual

download
11C/1-40 Fuses 1/1 Battery 2/35 Starter motor relay 2/76 Central locking/anti theft alarm (lock/alarm) control module 3/1 Ignition switch 3/71 Gear position sensor 4/9 SRS Supplemental Restraint System Crash Sensor 4/30 ECC climate control module 5/1 Combined instrument panel 6/25 Starter motor 6/26 Generator 24/2 Connector Firewall cable harness – Engine compartment harness 24/13 Connector Dashboard harness – Engine compartment harness 24/14 Connector Left door sill harness – Engine compartment harness 24/15 14-pin connector Engine compartment harness – engine harness 24/43 8-pin connector Engine compartment harness – engine harness 24/53 26-pin connector Engine harness – AW 50-42 31/4 Engine ground point (ground terminal – battery -engine) 31/7 Ground terminal driver’s side A post 31/44 Engine compartment ground point ( battery ground terminal – body)

1993 Dodge Dakota FUSE PANEL IDENTIFICATION

download
3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights. 9 – 15 Amp (Lt. Blue) Cigarette Lighter. 10 – 20 Amp (Yellow) Windshield Washers & Wipers. 11 – 20 Amp (Yellow) Turn Signals, Rear Wheel Anti-Lock Module. 12 – 10 Amp (Red) Radio. 13 – 4 Amp (Pink) Cluster Lights, A/C & Heater Controls, Cigarette Lighter Light & Ash Receiver Light, Radio Lights & Overdrive Switch Light. 14 – Not Used (1992-93); 15 Amp (Lt. Blue) (1994-95 Airbag Module, Speedometer, Gauges, Telltales. 15 – 2 Amp (Gray) Speed Control. 16 – 5 Amp (Tan) Gauges & Indicator Lights: Low Oil Light, Low Washer Light, Service Reminder Light, Transmission Oil Light, Brake Warning Light, Anti-Lock Brake Warning Light, Fuel Pacer Light, 4WD Indicator Light, Malfunction Indicator Light, Warning Buzzer, Overdrive Switch (1992-93); Transmission Oil Temperature Lamp, 4WD Lamp, Overdrive Module Seat Belt Warning Buzzer (1994-95). 17 – (Blank) Not Used. 18 – (Blank) Not Used. 19 – (Blank) Not Used. 20 – Not Used (1992-93); 25 Amp (Natural) (1994-95) Fog Lamps and Off Road Lamps. 21 – Turn Signal Flasher No additional definition. 22 – Time-Delay Relay No additional definition. 23 – Horn Relay No additional definition. 24 – Hazard Flasher No additional definition. 25 – Warning Buzzer

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.