Skip to content

06 kia rio clutch removal

You search PDF repair manual about 06 kia rio clutch removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

1996 Ford Bronco/F-Series Clutch Hydraulic Line REMOVAL AND INSTALLATION MANUAL

download
Clutch Hydraulic Line Removal 1. Note the routing of the clutch slave cylinder to clutch master cylinder tube (7A512) line from clutch master cylinder (7A543) to the clutch slave cylinder. 2. Remove retainer pin from clutch master cylinder holding clutch slave cylinder to clutch master cylinder tube in place. 3. Raise the vehicle and install suitable safety stands. 4. Disconnect clutch slave cylinder to clutch master cylinder tube from external clutch slave cylinder. On vehicles equipped with concentric clutch slave cylinders, remove tube using Clutch Coupling Tool T88T-70522-A. Installation 1. Follow the removal procedures in reverse order. 2. Bleed system. Refer to appropriate clutch hydraulic system bleeding procedure in the Adjustments portion of this section.

1996 Ford Bronco/ F-Series Clutch Hydraulic Line REMOVAL AND INSTALLATION MANUAL

download
Clutch Hydraulic Line Removal 1. Note the routing of the clutch slave cylinder to clutch master cylinder tube (7A512) line from clutch master cylinder (7A543) to the clutch slave cylinder. 2. Remove retainer pin from clutch master cylinder holding clutch slave cylinder to clutch master cylinder tube in place. 3. Raise the vehicle and install suitable safety stands. 4. Disconnect clutch slave cylinder to clutch master cylinder tube from external clutch slave cylinder. On vehicles equipped with concentric clutch slave cylinders, remove tube using Clutch Coupling Tool T88T-70522-A. Installation 1. Follow the removal procedures in reverse order. 2. Bleed system. Refer to appropriate clutch hydraulic system bleeding procedure in the Adjustments portion of this section. Hydraulic Clutch Control System, 4.9L, 5.0L and 5.8L Gasoline Engines with Mazda R2 and S5-47 ZF Light-Duty and 7.3L and 7.5L S5-47 ZF Heavy-Duty Transmissions

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

2001 Chevy Truck S10/ T10 Blazer Intake Manifold Replacement (Upper) Removal And Installation Manual

download
Intake Manifold Replacement (Upper) Notes Intake Manifold Replacement – Upper Removal Procedure Important: The upper intake does not have to be removed to remove the lower intake manifold. 1. Disconnect the breather tube at the air cleaner outlet duct 2. Remove the air cleaner outlet duct retaining wingnut. 3. Disconnect the IAT sensor harness connector 4. Remove the air cleaner outlet duct from the throttle body. 5. Disconnect the accelerator cable from the throttle body 6. Remove the accelerator cable from the accelerator control cable bracket. 7. Disconnect the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. 8. Disconnect the vacuum hose from the intake manifold for the vacuum tank. 9. Remove the power brake booster vacuum hose. 10. Disconnect the following electrical connectors: * The A/C compressor clutch (1) * The A/C compressor cutoff switch (5), if equipped * The Throttle Position (TP) sensor (2) * The Idle Air Control (IAC) motor (3) 11. Disconnect the following electrical connectors: * The fuel meter body assembly (1) * The Manifold Absolute Pressure (MAP) sensor(3) * The EVAP canister purge solenoid valve (2) 12. Remove the engine wire harness clip from the accelerator cable bracket. 13. Move the engine wiring harness aside. 14. Remove the accelerator cable bracket from the throttle body and the intake manifold. 15. Remove the accelerator and cruise control cable bracket from the throttle body. Leave the accelerator and cruise control cables on the bracket16. Remove the PCV valve hose assembly from the intake manifold and the valve rocker arm cover. 17. Remove the bracket for the engine wiring harness from the intake manifold stud. 18. Remove the fuel lines from the fuel meter body assembly. 19. Remove the EVAP canister purge solenoid valve.

2002 Ford F Super Duty 250 550/ Excursion Engine Removal And Installation Manual

download
Removal All vehicles 1. Disconnect both battery ground cables. For additional information, refer to Section 414-01 . 2. Loosen the clamps and remove the air cleaner outlet tube. 3. Remove the air intake tube and adapter. 1. Loosen the clamp. 2. Remove the bolts. 3. Lift the tube and adapter, disconnect the wastegate pressure hose, and remove the tube and adapter from the vehicle 4. Remove the degas bottle. For additional information, refer to Section 303-03 . Vehicles equipped with A/C 5. Recover the refrigerant. For additional information, refer to Section 412-00 . All vehicles 6. Remove the radiator grille, and the radiator grille opening panel. For additional information, refer to Section 501-02 . 7. Remove the bolts and position the hood latch aside. 8. Remove the three right side air deflector pushpins. 9. NOTE: Left side shown, right side similar. Remove the air charge cooler retainers. 10. Remove the radiator brackets and position the battery cable aside. 1. Remove the bolts and the brackets. 2. Detach the retainers and position the battery cables aside. 11. NOTE: Right side shown, left side similar. Remove the eight bolts and the radiator upper support. 12. Remove the radiator sight shield. Vehicles equipped with A/C 13. Disconnect the A/C condenser core inlet and outlet tubes. 14. Remove the A/C condenser. All vehicles 15. NOTE: Both the inlet and outlet ducts are removed the same way. Only the outlet duct is shown. Remove the inlet and outlet ducts from the charge air cooler. 1. Loosen the clamp. 2. Detach the ducts from the charge air cooler. 16. Remove the charge air cooler. 17. Disconnect the upper radiator hose from the radiator. 18. Remove the bolts and position the fan shroud on the fan. 19. Raise the vehicle. For additional information, refer to Section 100-02 . 20. Disconnect the degas supply and lower radiator hoses from the radiator. 21. Lower the vehicle. 22. Remove the radiator. 23. Remove the fan shroud. 24. CAUTION: The large clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it. Using the special tools, remove the fan and the fan clutch from the water pump pulley. 25. Rotate the belt tensioner counterclockwise and remove the drive belt. 26. Disconnect the manifold absolute pressure (MAP) sensor hose from the turbocharger compressor manifold.