Skip to content

07 impala 3 5 oil leak from front

You search PDF repair manual about 07 impala 3 5 oil leak from front, if there are search results will appear below. If search results do not exist, please search by others keyword.

FRONT WHEEL SPEED SENSOR CORROSION REPAIR MANUAL

download
1999-2002 CHEVROLET SILVERADO 2000-2002 CHEVROLET TAHOE, SUBURBAN 2002 CHEVROLET AVALANCHE 1999-2002 GMC SIERRA 2000-2002 GMC YUKON, YUKON XL LOCATED IN THE SEVERE CORROSION AREAS LISTED BELOW Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels. 3. Compress the front brake caliper pistons. 3.1. Install a large C-clamp over the top of the caliper housing and against the back of the outboard pad. 3.2. Slowly tighten the C-clamp until the pistons are pushed completely into the caliper bores. 3.3. Remove the C-clamp from the caliper. Important: It is not necessary to remove the front brake caliper from the bracket when removing the bracket in the next step. 4. Remove the two bolts that attach the front brake caliper mounting brackets to the knuckle. Notice: Support the brake caliper with heavy mechanic’s wire, or equivalent, whenever it is separated from its mount, and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak. 5. Remove the brake caliper and bracket as an assembly and support it with heavy mechanic’s wire or equivalent. DO NOT disconnect the hydraulic brake flexible hose from the caliper. 6. Mark the relationship of the rotor to the bearing hub. 7. If equipped, remove the rotor retaining push nuts from the wheel studs

2002 Chevrolet Impala Radiator Air Baffle and Deflector Replacement Manual

download
Radiator Air Baffle and Deflector Replacement – Upper Removal Procedure 1. Remove the radiator air baffle retainers. 2. Tilt the rear of air baffle upward slightly. Slide the air baffle rearward in order to disengage the upper and lower clips of the air baffle from the fascia support. 3. Remove the radiator air baffle. Installation Procedure 2002 Chevrolet Impala 1. Position the radiator air baffle to the vehicle. Tilt the rear of the air baffle upward slightly. Position the upper clip of the air baffle to the lower edge of the front fascia support C-channel. 2. Slide the baffle towards the front of the vehicle in order to completely engage the upper and lower clips of the baffle onto the fascia support. 3. Align the tabs at the rear of the air baffle to the openings in the upper radiator support. 4. Install the radiator air baffle retainers.

2003-2007 Dodge (DR/DH/D1/DC) Ram Truck Front EndShimmy On 4×4 Vehicles When Traveling Over Rough Surfaces In The Road

download
REPAIR PROCEDURE: 1. Raise the vehicle on an alignment rack (drive-on lift). 2. Verify the road tires are correctly sized and the tire tread is not excessively worn. Replace any worn tire before proceeding. Any new or old replacement tire should be equal to the original tires that came with the vehicle when it was new. Tire wear is not covered by the vehicle warranty. 3. Set the tire pressure for the FRONT TIRES to the following specification, regardless of the load being carried by the vehicle . Tire Size FRONT Tire Pressure LT235/80R17EorLT245/70R17E 448 Kpa (65 psi) LT265/70R17EorLT285/70R17E 414 Kpa (60 psi) 4. Set the tire pressure for the REAR TIRES as recommended for the vehicle configuration and load that is being carried at the time. Tire Size REAR Tire Pressure LT235/80R17EorLT245/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. LT265/70R17EorLT285/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. 5. Verify that the steering damper is operating correctly. a. Unbolt the end of the damper at the axle end. b. Cycle the damper rod by hand. c. There should be resistance to motion in both directions of the damper rod. d. Replace the damper if no resistance is present. 6. Verify both outer tie rod ends dustcovers are not worn. a. Attempt to rotate the dustcover by hand. b. If the dustcover on an outer tie rod end can be rotated, or is free and loose, then replace the tie rod (regardless of joint wear). 7. Inspect each outer tie rod end for internal wear. a. Maximum allowed wear (joint travel) fora tie rod end is 1.15 mm (0.045 in.). b. Install a dial indicator to the tie rod end (in-line with the vertical stud of the tie rod end). c. With a pry bar placed between the steering linkage and the axle tube, pry upwards while measuring the amount of joint travel (wear). d. Measure the amount of wear in the other outer tie rod end joint. e. If wear (joint travel) in either outer tie rod end is greater than 1.15 mm (0.045 in.), then replace the worn tie rod end. 8. Verify the torque on each outer tie rod end stud nut. The nut should be tightened to 122 Nm (90 ft. lbs.). 9. Make sure any worn outer tie rod ends have been replaced before proceeding further. 10. Verify all other steering linkage connections are tightened to their torque specifications.

2003 Kia Optima L4-2.4L Timing Belt Service and Repair Manual

download
3.Turn the crankshaft clockwise and align the timing marks so as to bring the No.1 cylinder to compression top-dead-center position. At this time the timing marks of the camshaft sprocket and the upper surface of the rocker cover should coincide, and the dowel pin of the camshaft sprocket should be at the upper side. Remove the auto tensioner. CAUTION: Rotate the crankshaft clockwise. 4.Remove the timing belt. NOTE: If the timing belt is reused, make an arrow mark indicating the turning direction (or the front of the engine) to make sure that the belt is reinstalled in the same direction as before 6.When the oil pump sprocket nut is removed, first remove the plug at left side of the cylinder block and insert a screwdriver to check the left counter balance shaft in position. Screwdriver used for this purpose should have a shaft 8 mm (0.3 inch) in diameter which can be inserted more than 60 mm (2.36 inch) 7.Remove the oil pump sprocket retaining nut and remove the oil pump sprocket. 8.Loosen the right counter balance shaft sprocket mounting bolt until it can be loosened by hand. 9.Next, remove tensioner “B” and remove timing belt “B”. CAUTION: After timing belt “B” has been removed, do not attempt to loosen bolt while holding sprocket with pliers, etc. 10.Remove the crankshaft sprocket “B” from crankshaft. INSPECTION Sprockets, Tensioner Pulley, and Idler Pulley 1.Check the camshaft sprocket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2.Inspect the tensioner pulley and the idler pulley for easy and smooth pulley rotation and check for play or noise. Replace as necessary. 3.Replace if there is grease leak

1994 Ford Explorer FRONT WHEEL BEARINGS MANUAL

download
FRONT WHEEL BEARINGS Dana 35-IFS & Automatic Locking Hubs 1. Raise and support vehicle. Remove front wheel assemblies. Remove retaining washers from wheel lug nut studs. See Fig. 1 . 2. Remove automatic locking hub assemblies. Remove snap ring and axle shaft spacer. Carefully pull plastic cam assembly from bearing adjusting nut. Remove 2 plastic thrust washers from adjusting nut. 3. Using magnet, remove locking key from spindle keyway. It may be necessary to rotate adjusting nut slightly to relieve pressure for locking key removal. Loosen adjusting nut with 2 3/8″ Hex Socket (T70T- 4252-B). 4. Tighten adjusting nut to 35 ft. lbs. (47 N.m) while turning hub back and forth to seat bearings. Spin hub and back off adjusting nut 90 degrees. Retighten adjusting nut to 16 INCH lbs. (1.8 N.m). 5. Align nearest hole in adjusting nut with center of spindle keyway slot. If necessary, advance nut to next lug. Install locking key in spindle keyway under adjusting nut. Install 2 thrust washers. Press plastic cam assembly onto adjusting nut while lining up key in fixed cam with spindle keyway. 6. Install axle shaft spacer. Clip snap ring onto end of spindle. Install automatic locking hub assembly with 3 legs of hub assembly inserted into 3 pockets of cam assembly. Install retaining washers and wheel assembly. Check hub and rotor assembly end play. End play should be 0-.003″ (0-.08 mm)