Skip to content

1970 cadillac deville tilt steering column horn parts

You search PDF repair manual about 1970 cadillac deville tilt steering column horn parts, if there are search results will appear below. If search results do not exist, please search by others keyword.

1988 Cadillac DeVille Steering Column Service and Repair Manual

download
Disassembly 1. Remove dash panel bracket and store bracket in a safe place to prevent damage to mounting capsules. 2. Place column in a vise using both weld nuts of either set A or B, Fig. 29. The vise jaws must clamp onto the sides of weld nuts indicated by arrows shown on set B. Do not place column in vise by clamping onto only one weld nut, by clamping on one weld nut of both sets A and B or by clamping onto the sides not indicated by arrows, as damage to column could result. 3. Inspect steering shaft to determine type of thread used for steering shaft nut. Metric type shafts can be identified by a groove located in area of steering wheel locating splines, while shafts with American type threads do not have this groove. If shaft has metric type threads, the forcing screw of Lock Plate Compressor Tool J-23653 must be removed and replaced with the metric forcing screw J-23653-4 before installing lock plate compressor tool on steering shaft. Compress lock plate using lock plate compressor tool, then pry snap ring from shaft groove and discard wing. Remove lock plate compressor tool and lock plate. 4. Remove directional signal switch, lock cylinder and ignition key warning switch, then remove steering shaft from lower end of column. 5. On power steering columns, remove steering shaft lower bearing from plastic adapter at lower end of column. 6. Remove four turn signal housing to column jacket retaining screws and remove housing and shroud assembly. 7. Remove three shroud to signal housing retaining screws and remove shroud. 8. Using hand as shield to prevent lock inhibitor lever spring wire from flying out, remove lock inhibitor lever and spring wire. 9. Lift ignition switch actuating rod, rack assembly, shaft lock bolt and spring assembly from housing, then if necessary, remove rack preload spring. 10. Remove ignition switch actuator sector through lock cylinder hole by pushing firmly on block tooth of sector with a blunt punch or screwdriver.

1989 Chevrolet Corvette V8-350 5.7L Steering Column Service and Repair Manual

download
SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined. 2. Place turn signal lever to the right turn position, then remove screw and switch actuator pivot assembly (Nos. 11 and 44 in Fig. 59 ). 3. Remove the screws and the wiring protector (Nos. 10 and 45). 4. Remove turn signal switch, then gently pull wire harness through column housing shroud, column housing and lock housing cover. 5. Reverse procedure to install, noting the following: a. Torque turn signal switch screws (No. 10 in Fig. 59 ) to 27 inch lbs. and torque screw (No. 11) to 18 inch lbs. BUZZER SWITCH ASSEMBLY & STEERING COLUMN LOCK CYLINDER SET

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

1989 Toyota 4Runner STEERING COLUMN REMOVAL AND INSTALLATION INSTRUCTIONS

download
REMOVAL & INSTALLATION STEERING COLUMN Removal 1) Disconnect battery ground cable. Remove steering wheel. On Cressida, Corolla, MR2 and Tercel models, remove fuse box cover, lower instrument trim panel and air duct from under steering column. 2) On all models, remove upper and lower steering column covers. Remove combination switch. Mark position of “U” joints and shaft for reassembly. 3) On models with “U” joints, remove “U” joint retaining bolt. On models with flexible joint, remove flexible joint retaining bolt. NOTE: On 2WD Pickup models, remove steering column with intermediate shaft attached. 4) On all models, mark position of joint and pinion shaft for reassembly. Remove intermediate steering shaft. 5) Remove floor pan cover bolts. Remove tilt bracket-to- dashboard mounting bolts. Remove steering column toward inside of vehicle. Fig. 1: Exploded View of Camry, Corolla, MR2 & Tercel Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Celica, Cressida & Supra Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 3: Exploded View of Land Cruiser, Pickup, Van & 4Runner Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Installation 1) To install steering columns, reverse disassembly procedure. Grease main steering shaft and all bearings. 2) Ensure marks made to flexible couplings and to “U” joints are aligned. Ensure steering column and shafts do not bind after installation. STEERING COLUMN OVERHAUL NOTE: Camry, Corolla, MR2 and Tercel steering columns are similar. Some of the following procedures will not pertain to all models. Disassembly (Camry, Corolla, MR2 & Tercel) 1) Remove tension springs, grommets and screws from tilt bracket. Remove tilt lever left-hand set bolt. Remove column upper support lock bolt. 2) Remove tilt steering support bolts and pawl set bolts. Place bushings and “O” rings aside and keep them clean. Remove ignition lock cylinder. 3) Using a screwdriver, push 2 thrust stoppers into bearing retainers. Pull out shaft from column. Remove the No. 1 column ring, bearing retainer, thrust stoppers and No. 2 column ring from shaft. 4) Remove snap ring and lower bearing from shaft. Remove bearing inner snap ring. Remove upper bracket retaining bolts and ground strap. Separate upper bracket from column. Inspection 1) Check that steering lock mechanism operates properly. Check upper bearing for smooth rotation or excessive noise. Replace upper bearing (if necessary). 2) Using Drift (09631-00020) and Adapter (09627-30010), drive bearing from upper bracket. Pack new bearing with grease. Using the same drift and adapter used in removal, drive new bearing into upper bracket. 3) Inspect lower bearing for smooth rotation or excessive noise. If lower bearing shows signs of wear or damage, replace with a new one. Reassembly 1) Install upper bracket onto column. Install ground strap. Tighten retaining bolts to 14 ft. lbs. (19 N.m). Install inner snap ring on shaft groove nearest to center of shaft. 2) Install lower bearing and lower bearing snap ring. Place No. 2 column ring into position next to bearing on side nearest center of shaft. See Fig. 4.

Chevrolets Tri-Five Steering Column to Steering Box Installation Instructions

download
The spline in your stock steering wheel is the same as the one on the new column, so no modifications are needed here. Turn the wheel over and find two screws that hold a metal tap to the wheel. This tab is what is used to cancel your turn signals. Remove the two screws and the tab as you will not be using them with your new column. You will have to drill a 1/2″ diameter hole in the wheel 3/4″ from the center of the splined hole in the center of the steering wheel at 45° (looking at the front of the wheel). If this can’t be done because of screw holes for a puller, try to get the hole as close as possible on either side. Do not drill out puller holes, you may need them later to pull the wheel. Install horn kit, if purchased. If the horn kit with ring is purchased, the ring is to be siliconed onto the steering wheel. If it doesn’t fit on exactly right, use a file or die grinder to trim inside. (If it’s way off, call us and we may something that will fit or we can make you something that will fit.) Next, install the wheel on the column. If it doesn’t want to go on at first, move the horn cam with your thumb and index finger a little one way or the other until the wheel drops down fully. This horn cam is what cancels the turn signals, so with this horn cam at 10:30, the steering box half way between full left and right, and the road wheels pointed straight ahead, the turn signals will cancel at the right time