Skip to content

1972 ford courier repairs

You search PDF repair manual about 1972 ford courier repairs, if there are search results will appear below. If search results do not exist, please search by others keyword.

Ford F-Series Column Shift Repairs Manual

download
It’s a simple system. To remove the assembly, start by removing the column shift lever. This is super easy; just use two small punches to depress the two spring-loaded pivot pins on the lever, then pull the lever out. Be aware: the pivot pins and spring will shoot out. Next go under the hood, and undo the two bolts holding the clamp piece just above the steering box. The lower half of the clamp will come free. The upper half is locked to the “shoe” plate under it, and to the steering column, with a round peg cast into it. So you need to pry the shoe up away from the steering column to get the peg clear of the column. Once you do that, you need to pry the upper half of the clamp away from the shoe, so the peg is clear of the shoe. Once it is clear, you can slide the end piece off the shifter tube. Then slide the wave washer and 2-3 lever off. To get the 1-R lever off, you’ll need to pull a steel pin out of the shifter tube. It should just drop out. Then slide the lever, wave washer, and shoe off the tube. Push the shifter tube up to get the clearance needed for the shoe. The shifter tube is a hollow steel tube, with a hole drilled thru it near the bottom. In this hole there is a steel pin (the one just removed). The steel pin engages into slots in the 1-2 and 3-4 levers, to move them. As you can see, there isn’t a lot of wear in my shift levers’ slots. The pin shows some wear, where the tube contacts it. The pin is hardened steel and the shifter tube is mild steel, so the tube will be worse than the pin. The pins are available from Obsolete Ford Parts and others, P/N 01A-7337, only a couple of bucks. Getting the shifter tube out is pretty easy; just drop the column support (remove the bolts to instrument panel and loosen the pinch bolt) down to the floor, and you’ll be able to swing the shift tube to the side to clear the steering wheel, and pull it out. My pin wasn’t that worn, it’s the hole in the tube. The tube is hollow but actually has a steel plug inside it with a hole for the pin. It is pushed inside the tube and then peened in two places thru the outer tube (they punched the outer tube to lock the inner plug). inner plug had gotten loose inside the tube, too. If this is your situation, you could just drill and pin the plug to the outer tube, and get a good improvement. I wanted “like new”, so I took my shifter tube to my favorite machinist (Gene at Noor Mfg. in Albuquerque, a super guy). He made up a whole new lower end for the tube out of 1018 carbon steel. It’s got a spigot on the upper end that was pressed into the remaining tube, welded, then turned down. It is better than new! Look at the difference in the shape of the hole. Price for the work was very reasonable

2001 Ford Truck F 150 Engine – Spark Plug Hole Thread Repair Procedure

download
SERVICE PROCEDURE Ford Motor Company now authorizes LOCK-N-STITCH aluminum insert and tool kit as a proper repair procedure. Follow the procedure included in the tool kit for using the tools and inserts. Tool kits and inserts can be ordered from Rotunda by calling 1-800-Rotunda (768- 8632). Choose option two (2), part number 302-00001. NOTE FORD MOTOR COMPANY HAS DETERMINED THAT REPAIRS MADE WITH THESE ALUMINUM INSERTS AND LOCK-N-STITCH TOOLS DO NOT AFFECT THE HEAT TRANSFER FUNCTION BETWEEN THE SPARK PLUG AND THE CYLINDER HEAD. NOTE THIS PROCEDURE IS NOT AUTHORIZED AS A FORD WARRANTY REPAIR. FOR VEHICLES WITHIN WARRANTY, REPLACEMENT OF THE CYLINDER HEAD IS RECOMMENDED. NOTE THIS IS THE ONLY FORD AUTHORIZED PROCEDURE FOR SPARK PLUG THREAD REPAIRS. NOTE THIS PROCEDURE IS AUTHORIZED FOR ESP REPAIRS AND RETAIL REPAIRS. WARRANTY STATUS: Information Only – Not Warrantable

K40016 ADD-A-LEAF SPRING KIT INSTALLATION INSTRUCTIONS

download
CHEVY 1982-98 S Series all 2WD/4WD 1972-82 LUV PU 2 WD DODGE 1994-99 Ram 1500 2WD 1994-00 Ram 1500 4WD FORD 1990-96 F 150 std or ext cab 2WD 1982-89 F 150 std or ext cab 2WD 1983-1996 Ford Bronco II 4WD 1983-1996 Ford Bronco II 2WD 1983-1997 Ford Ranger 2WD/4WD 1990-00 Ford Ranger 2WD 1983-97 Ford Explorer 2WD/4WD 1972-84 Ford Courier 2WD K40016 ADD-A-LEAF SPRING KIT JEEP 1984-01 Jeep Cherokee 1974-86 CJ-5/CJ-7/CJ-8 4WD 1967-73 Jeepster/C101/C101 w multileaf Jeep Wrangler 1987-96 Front and Rear LAND ROVER 1959-1981 All 4wd MITSUBISHI 1986-91 Montero 1982-84 PU 2WD/4WD NISSAN 1968-1997 PU/Pathfinder 2WD/4WD TOYOTA 1963-98 Toyota PU/4 Runner with 2.5″ rear springs The K40016 Add-A-Leaf Spring Kit retrofits onto the following vehicles: The kit consists of two each 28″ Leaf Springs and two sets of two each longer bolts and nuts of different diameters. The same diameter bolt currently on the vehicle should be used and the other set discarded. • PLEASE READ ALL INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION • You must use 2-large “C-clamps” or a large vise to contain the elastic potential energy stored in a leaf spring when the center bolt is removed. • The new leaf spring will be placed in the existing spring assembly in a progressive pyramid shape. Example – if your number 1 Spring is 32″ long and the next one is 25″ long, the new Add-A-Leaf Spring should be place between them. • Some vehicles will have a flat helper stack. SEE ILLUSTRATION – DO NOT INSTALL THE NEW ADD-A-LEAF SPRING IN OR BELOW THE HELPER SPRIN(S). Helper spring assembly. Do not install Add-A-Leaf in or below this assembly Lowest allowable position for Add-A-Leaf

2000 Ford Ranger Cooling System Draining Filling and Bleeding Repair Manual

download
NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle, For additional information, refer to Section 100-02 . 3. Remove the lower radiator cover. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant such as VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants can degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, or brine, or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolants unless they meet the requirements of Ford specification ESE-M97B44-A or WSS-M97B51-A1. Not all coolant recycling processes meet these Ford specifications. Use of such coolants can harm the engine and cooling system components. All engines 1. Install the lower radiator cover.

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5