1979 ford f250 owners manual

You search PDF repair manual about 1979 ford f250 owners manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1979 ford f250 owners manual Direct Download speed 5432 Kb/s

  1979 ford f250 owners manual Full Version speed 8172 Kb/s



1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

How to Fix Po446 Code ford escape xls, 555 ford backhoe repair manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, Ford E 450 Cutaway Manual, ford 9 inch repair manual, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, Ford OBD1 Codes and Fixes for Them, how many quarts of transmission fluid does 2012 ford e450 take?

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

0

Filed Under (Ford Manuals) by admin on 15-05-2012

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

Related Content:

0761 emission code ford, 2004 ford ranger owners manual pdf, 86 ford ranger repair manual, ford five hundred repair manual 2007 pdf, ford ranger transmission repair manual, free download jo8c parts book, manual lever position sensor troubleshooting, repair manuel 91 suburu loyle, wiring for a zemmadic 410 pivot

1994 Ford Truck F 350 2WD Pickup A/T – E40D No Upshifts or Harsh Upshifts/ 4th Gear Starts

0

Filed Under (Ford Manuals) by admin on 07-01-2012

download
All of these concerns can be the result of an inappropriate Manual Lever Position (MLP) sensor signal. The MLP sensor consists of six resistors connected in series (ganged). The resistance of the MLP sensor will vary based on which range the transmission is in. The MLP circuit can be checked using the following steps. (Step 1) Check the MLPS ground: Turn the ignition on. The voltage on pin 46 (sensor ground ) should not exceed .1v. If the voltage is excessive, add an additional ground to the existing ground wire (figure 2). Figure 2 Splice an additional ground from the existing ground wire to a known good ground.The negative post of the battery is the best. This view is of the pins of the MLP connector pins. (Step 2) Check the MLPS voltage: The voltage at pin 30 should vary-in increments- according to the position of the manual lever (figure 3). MLP voltage (ignition on) should be within 20% of these specifications Note It is recommended that you use a break-out box. If a break-out box is not available, you will need to pierce the wires to pins 30 and 46 for these tests. (Step 3) Check the resistance of the MLPS: The resistance of the MLPS (pins 30 and 46) should change-in increments-with the position of the manual lever (figure 4). Note If this test is being done with a break-out box, disconnect the computer first (make sure the ignition is off). If this test is being done without a break-out box, disconnect the MLPS from the vehicle harness. REVISED This is a revised bulletin. Remove bulletin 230 from your files. Note Testing beyond this point will include tests of the harness. Consult the appropriate repair manual for this.

Related Content:

Ruff and Tuff Parts Manual, 1994 f-350 owners manual DOWNLOAD, atsg 4r70w pdf, Agility CNG Fuel System troubleshoot, 91 4l80e rebuild manual download, Hubsan X4 Owners Manual, technifor x-range uc500, jo8c engine workshop manual, JO8C PDF, pdftown manuals

Ford SVT Contour/ Mercury 2.5L V-6 Cougar (5 Speed Manual Transmission Only) Supercharger System Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-05-2012

download
1998-2000 FORD SVT CONTOUR/ MERCURY 2.5L V-6 COUGAR Installation Instructions For best performance and continued durability, please take note of the following key points: 1. Use only premium grade fuel 92 octane or higher (R+M/2). 2. The engine must have stock compression ratio. 3. If the engine has been modified in any way, check with Vortech prior to using this product. 4. Always listen for any sign of detonation (pinging) and discontinue hard use (no boost) until problem is resolved. 5. Perform an oil and filter change upon completion of this installation and prior to test driving your vehicle. Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and filter every 3,000 miles or less. Never attempt to extend the oil change interval beyond 3,000 miles, regardless of oil manufacturer’s claims as potential damage to the supercharger may result. 6. Before beginning installation, replace all spark plugs that are older than 1 year or 10,000 miles with original heat range plugs as specified by the manufacturer and reset timing to factory specifications (follow the procedures indicated within the factory repair manual and/or as indicated on the factory underhood emissions tag). Do not use platinum spark plugs unless they are original equipment. Change spark plugs at least every 20,000 miles and spark plug wires at least every 50,000 miles. TOOL & SUPPLY REQUIREMENTS: •Factory Repair Manual •3/8″ Socket and Drive Set: SAE & Metric •1/2″ Socket and Drive Set: SAE & Metric •3/8″ NPT Tap and Handle •Adjustable Wrench •Open End Wrenches: 3/8″, 7/16″, 1/2″, 9/16″ •Center Punch •Ford Springlock 3/8″ Fuel Fitting Disconnect Tool •5 Quarts SH/CF Rated Quality Engine Oil •Oil Filter and Wrench •Flat #2 Screwdriver •Phillips #2 Screwdriver •Heavy Grease •Silicone Sealer •Drill Motor •1/8″, 3/16″, 27/64″ Drill Bits •9/16″ Rota Broach Tool (also available from Vortech) •Molylube •Wire Strippers and Crimpers •Utility Knife If your vehicle has in excess of 10,000 miles since its last spark plug change, then you will also need: •Spark Plug Socket •NEW Spark Plugs

Related Content:

free repair manual for 1998 Ford Contour SVT, repair manual for 1998 Ford Contour SVT, 97 Ford Thunderbird Repair Manual, 98 contour svt 2 5 alternator diagram, downloadable owners manual 1998 ford contour, Ford five hundred spark plug change, how to change thermostat on a 1998 ford contour, ou change the antifreeze in a 2008 G6 3 9

2008 Ford F-250/350/450 6.4L Powerstroke diesel aft-filter system Installation Manual

0

Filed Under (Ford Manuals) by admin on 08-12-2011

download
Installation instructions: 1.) Raise and support vehicle. 2.) Lubricate all factory rubber hangers and pipe slip-connectors with penetrating oil. 3.) Loosen clamp, attaching inlet of stock muffler to inlet pipe. 4.) Remove muffler/tailpipe assembly from inlet pipe and rubber hangers; remove from vehicle. Removal of muffler/tailpipe can be made easier by first cutting the tailpipe from the muffler with a reciprocating saw. 5.) Remove hanger rod on inlet pipe from rubber frame hanger. 6.) Loosen clamp attaching inlet pipe to outlet of converter and remove pipe from vehicle. 7.) Place supplied 3.5? clamp with hole over small end of supplied adapter and install onto outlet of converter. Engage slot in adapter with index bump on converter outlet and place hole in clamp over bump. Tighten clamp fully. 8.) Place one supplied 4? clamp over inlet pipe slip-connector and install pipe onto adapter. Insert hanger rod on pipe into corresponding rubber hanger on frame. 9.) Rotate inlet pipe as needed to orient end of hanger rod, which is inserted into rubber hanger, in a horizontal position and tighten clamp at slip-connector fully 10.) Place one supplied 4? clamp over muffler inlet and install muffler onto inlet pipe. 11.) Place one supplied 4? clamp over inlet of tailpipe section “A” and install pipe onto muffler and into corresponding factory rubber hangers just above muffler. 12.) Place one supplied 4? clamp over inlet of tailpipe section “B” and install pipe into rear-most rubber frame hanger and onto outlet of tailpipe section “A”. 13.) Place remaining 4? clamp over tip inlet and install tip onto outlet of tailpipe section “B”. 14.) Align all components for desired fit and tighten all clamps fully

Related Content:

6 0work shop manual pdf, 1957 ford o matic transmission torque convertor torque spec, 1995 Ford Mustang conv owners manual, 2003 windstar exhaust hanger rubber, 99 ford windstar rubber exhaust support, 99 ford windstar tail pipe rubber hanger, Muffler hanging silencer hanger exhaust hanger auto shock absorber, replacing the exhaust grommet 2000 windstar

2006 Ford F-SUPER DUTY Class A Motorhome Chassis INCOMPLETE VEHICLE MANUAL

0

Filed Under (Ford Manuals) by admin on 26-05-2012

download
Certain exhaust system components, including exhaust heat shielding systems, have been installed on some vehicles in our assembly plants in an effort to provide protection against engine compartment and exhaust system temperatures. Subsequent aftermarket installers/manufacturers are responsible for providing thermal protection (e.g. underbody heat shields) for any structure and/or equipment added to the vehicle and should not remove any components or exhaust heat shielding installed on the vehicle by Ford Motor Company. All exposed interior sheet metal of closed structures (e.g. fl oor pan of cab and/or secondary structure, tool boxes, etc.) should be covered with an insulating material capable of protecting vehicle occupants and contents from temperatures potentially up to 700°F. OZONE DEPLETING SUBSTANCE (ODS) OZONE DEPLETING SUBSTANCE (ODS) The Clean Air Act of 1990, Section 611 requires any product (i.e., completed vehicle) containing or manufactured with any Class I Ozone Depleting Substance on, or after May 15,1993 must be identifi ed with a “clearly and conspicuously attached label.” Ford Motor Company has eliminated Class I ODS from its manufacturing processes. All 2006 Ford Truck incomplete vehicles will not have Class I ODS content. Manufacturers, including subsequent stage manufacturers, are required to label their products if the product, including any component (whether manufactured by that manufacturer or not), contains a Class I ODS or if the manufacturer used a Class I ODS in the manufacturing of the product. In the case where Ford Motor Company provides a label saying the incomplete vehicle contains a Class I ODS that information must be placed on the product warning label. (See EPA regulation on wording, placement, size, and combining labels.) In Canada consult the appropriate Provincial or Territorial Ministry of Environment. EMISSION CONTROL INFORMATION LABEL To meet United States Environmental Protection Agency regulations, the Important Vehicle Information (tune-up and fuel tank capacity) labels must be affi xed in a location that is readily visible after installation and in such a manner that it cannot be removed without destroying or defacing the label. The label shall not be affi xed to any equipment that is easily detached from the vehicle. When emission control labels are supplied but not attached to the vehicle (i.e., tune-up label or fuel tank label), they must be permanently mounted in a readily visible location to meet the preceding requirements. In addition, whether the label is already affi xed or to be affi xed, no components shall be installed which visibly obscure the label in any way that fails to satisfy the visibility requirements described in the California Emission Control Label Specifications. For Canadian requirements consult Section 1100 8 (1) (d) (i), (ii), & (iii). CALIFORNIA FUEL VAPOR RECOVERY California regulations require that the vehicle fuel systems be designed to accommodate a vapor recovery fueling nozzle including unobstructed access to the fi ll pipe. Fuel fi ller pipes installed per the Figure B on page 15 will comply with the “Specifi cations For Fill Pipes and Openings of Motor Vehicle Fuel Tanks” referenced in Title 13 California Administrative Code provided no part of the aftermarket body, as installed, intrudes within a 254mm [10 in] radius cylinder which has its axis parallel to the ground at point “Z” and extends outward from the Ford Motor Company supplied fuel pipe housing component. The fuel pipe housing component is shown on the referenced fi gures and is attached to the aftermarket body via 4.76 mm [.188 in.] diameter rivets. Fuel fi ller pipes installed using the alternative bracket shown in Figure B, will comply with the above California vapor recovery regulations provided the aftermarket body does not interfere with the access zone as defi ned by the California Air Resources Board, and the areas adjacent to this opening cannot foreseeably damage the nozzle bellows or face plate of nozzles during insertion, latching, disposing or removal

Related Content:

ford class c chassis cruise control operation manual, 1990 Ford Class B motor home how to manual, 1996 ford e super duty motorhome specifications, 1998 F-Series Super Duty Class A Motorhome Chassis Manual, 1999 Ford F-250 Truck OBD II Powertrain Control & Emissions Diagnosis Manual, 2006 Ford F-53 motorhome chassis wheel bearing part numbers, how to replace a blend door actuator in a 2002 fourwinds class c motorhome, u2023 code ford explorer

1996 Ford Taurus Transmission and Drivetrain Automatic Transmission/Transaxle Removal and installation Manual

0

Filed Under (Ford Manuals) by admin on 20-04-2012

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve. Zoom Sized for Print Oil Pump And Valve Body Bolt Tightening Sequence

Related Content:

can a 2002 taurus transmission be removed without removing subframe, CLEAN THROTTLE BODY CHEVY ENVOY, how to replace the bumper cover on a 1998 Isuzu Rodeo, 03 Chevy impala removing valve cover, volvo xc90 2 9 rocker cover removal, valve cover gaskets on 2002 Escape V6, Removing Valvebody on 722 6, remove 2003 taurus transmission lowering only one side subframe, how to removed a valve body from volvo s 70, how to remove valve cover 5 4 32v navigator

K40016 ADD-A-LEAF SPRING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 19-04-2012

download
CHEVY 1982-98 S Series all 2WD/4WD 1972-82 LUV PU 2 WD DODGE 1994-99 Ram 1500 2WD 1994-00 Ram 1500 4WD FORD 1990-96 F 150 std or ext cab 2WD 1982-89 F 150 std or ext cab 2WD 1983-1996 Ford Bronco II 4WD 1983-1996 Ford Bronco II 2WD 1983-1997 Ford Ranger 2WD/4WD 1990-00 Ford Ranger 2WD 1983-97 Ford Explorer 2WD/4WD 1972-84 Ford Courier 2WD K40016 ADD-A-LEAF SPRING KIT JEEP 1984-01 Jeep Cherokee 1974-86 CJ-5/CJ-7/CJ-8 4WD 1967-73 Jeepster/C101/C101 w multileaf Jeep Wrangler 1987-96 Front and Rear LAND ROVER 1959-1981 All 4wd MITSUBISHI 1986-91 Montero 1982-84 PU 2WD/4WD NISSAN 1968-1997 PU/Pathfinder 2WD/4WD TOYOTA 1963-98 Toyota PU/4 Runner with 2.5″ rear springs The K40016 Add-A-Leaf Spring Kit retrofits onto the following vehicles: The kit consists of two each 28″ Leaf Springs and two sets of two each longer bolts and nuts of different diameters. The same diameter bolt currently on the vehicle should be used and the other set discarded. • PLEASE READ ALL INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION • You must use 2-large “C-clamps” or a large vise to contain the elastic potential energy stored in a leaf spring when the center bolt is removed. • The new leaf spring will be placed in the existing spring assembly in a progressive pyramid shape. Example – if your number 1 Spring is 32″ long and the next one is 25″ long, the new Add-A-Leaf Spring should be place between them. • Some vehicles will have a flat helper stack. SEE ILLUSTRATION – DO NOT INSTALL THE NEW ADD-A-LEAF SPRING IN OR BELOW THE HELPER SPRIN(S). Helper spring assembly. Do not install Add-A-Leaf in or below this assembly Lowest allowable position for Add-A-Leaf

Related Content:

1969 ford truck ranger 390 overheating did not start till change water pump, fluid spec for 2004 ford ranger, f53 96 manual, 83 ranger wiring diagram, 1996 Ford RV specifications, 1996 Ford Explorer Repair Manual, 1996 ford explorer manual, 1996 f53 manifold exhaust repair, 1986 555b ford backhoe injector pump, ford ranger 2 3 engine diagram

2003 Ford F-Super Duty 250-550/ Excursion Rear Drive Axle/Differential/ Ford 10.50-Inch Ring Gear Installation Manual

0

Filed Under (Ford Manuals) by admin on 30-06-2012

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 2003 F-Super Duty 250-550/Excursion Workshop Manual 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plat 2003 F-Super Duty 250-550/Excursion Workshop Manual 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim

Related Content:

ford e450 super duty manual, Sub Zero 550 Troubleshooting Guide, Ford 550 Backhoe Manual

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia