Skip to content

1986 mercedes 190 e shop manual pdf free

You search PDF repair manual about 1986 mercedes 190 e shop manual pdf free, if there are search results will appear below. If search results do not exist, please search by others keyword.

1984 Mercedes Benz 190E Fuel Delivery and Air Induction Engine Testing And Adjustment Manual

download
Note: Test and adjust lambda control with a lambda control tester. The lambda control and the idle speed emissions level must not be tested when the engine is very hot, e.g. immediately after driving sharply or after measuring engine output on the dynamometer. Testing, adjusting 1 Complete measurement sheet. 2 Switch off air conditioning or automatic climate control. Move selector lever into position “P”. 3 Read out DTC memory. Note: Not available on model year 1984-1986. 4 Connect testers: oil remote thermometer (018)124 589 07 21 00 lambda control tester (012) twin socket (031) trigger clamp (011) exhaust probe (005)126 589 11 63 00 CO measuring instrument (006) engine tester with oscilloscope (030) multimeter (003) test cable (033)102 589 04 63 00. 5 Position extraction device (014) at exhaust tail pipe. 6 Check engine coolant level, adjust to correct level. 7 Check engine oil level, pay attention to condition of oil (visual inspection). 8 Take off air cleaner. 9 Check ease of movement and condition of throttle control linkage and throttle valve. Grease all bearing points and ball sockets. 10 Check fulcrum lever, adjust. Check whether the roller (15) in the fulcrum lever (13) is resting free of tension against end stop. Adjust fulcrum lever (13) with the connecting rod (2), if necessary, so that the roller (15) is resting free of tension against end stop. 11 Idle stop. Check whether the throttle valve is resting against idle stop. Disconnect connecting rod (2) for this step. Adjust throttle control. Engines with cruise control only. Check whether the actuator is resting against idle stop of cruise control by pressing the lever of the actuator clockwise against idle stop at cruise control. When attaching the connecting rod (21), ensure that the lever of the actuator is lifted approx. 1 mm off the idle stop at the cruise control. Adjust tie rod, if necessary. Adjust throttle control. 12 Check wide open throttle stop from the accelerator pedal , adjust. 13 Voltages Test (battery and ignition coil ): No-load voltage Connect voltmeter to the battery, paying attention to the polarity, and take reading of voltage. Specification: 12.2 volts . Ignition coil Switch on ignition with engine not running. Test the voltage terminal 15 to ground at contact 5 of diagnostic connector. Specification: battery voltage Test difference in voltage between terminal 15 and terminal 1 at contacts 5 and 4 of diagnostic connector. Specification: 0 volts If the specified values are not reached, test

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly

1986 Ford Truck F 150 2WD Pickup Emission Maintenance Warning Module-Service Manual

download
EMISSION MAINTENANCE WARNING MODULE SERVICE INFORMATION ^LAMP – “EMISSIONS/CHECK ENGINE” – EMISSION MAINTENANCE WARNING MODULE – SERVICE INFORMATION LIGHT TRUCK: 1985-89 BRONCO 1985-87 BRONCO II 1985-89 ECONOLINE, F- 150, F-250, F-350 1985-88 RANGER 1986-87 AEROSTAR ISSUE: The Emission Maintenance Warning “EMW” module operates a light that is located on the instrument panel. For 1985-87 model year vehicles, the light will display the word “EMISSIONS”. For 1988-89 model year vehicles, the light will display the words “CHECK ENGINE”. When the light is lit, it is indicating that the 60,000 mile emission maintenance should be performed. After the maintenance is performed the EMW module must be reset to zero time. Another type of module is the “IMS” module. This module is not part of the light circuit and does not require maintenance. At a predetermined time, the IMS module directs the EEC IV processor to make a strategy change. A third type of module is the “COMBO” module. This module combines the functions of the IMS and the EMW modules. ACTION: Refer to the following module application charts for the specific vehicle application and location of the different types of modules. NOTE: FOR APPLICATIONS NOT LOSTED IN THE FOLLOWING MODULE APPLICATION CHARTS, THE “CHECK ENGINE” LIGHT IS CONTROLLED BY THE EEC IV PROCESSOR. THESE VEHICLES DO NOT USE THE “EMW” MODULE

Jaguar Electronic Parking Brake Diagnostic Aid/ Repair Manual

download
INITIAL VISUAL INSPECTION 1. Place the vehicle on a suitable lift. 2. Visually inspect the parking brake cable installation, parking brake caliper levers and general condition of the brakes. • Ensure the caliper levers are returning fully to their stops. • Confirm the cable routing is correct • Confirm that the cable is securely fixed at all abutment points and is free to move within the C-clip. • Where cable routing goes over the top of the stabilizer bar drop links, confirm that the stabilizer bar rubber deflector blocks are fitted, and that the brake cables have not been getting trapped behind the stabilizer bar drop links (look for tell-tale marks on the links and/or cables). NOTE: Global Technical Reference (GTR) lookup sequence is as follows: GTR Home > NAS > Model > Service Information > Model Year > Workshop Manual > 2: Chassis — Section 206: Brake System NOTE: Refer to the correct section by reference to VIN and based on whether the vehicle is fitted with high performance brakes or not. 3. Rectify any obvious faults. 4. If no obvious faults are found or further guidance is needed to rectify faults, please proceed to the next stage of this bulletin. Refer to GTR Sections 206-05 (parking Brake and Actuation) and GTR Section 206-04 (Rear Disc Brake). 5. If any faults were found and rectified, it will be necessary to re-calibrate the parking brake after rectification. See ‘Parking Brake Calibration’ procedure. PREPARE THE PARKING BRAKE FOR DETAILED INSPECTION CAUTION: Jaguar IDS DVD 111 or later and Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during diagnosis. 1. Install the Midtronics PSC-550 Vehicle Power Supply to the vehicle. 2. Connect the IDS to the vehicle and begin a new diagnostic session by entering the correct VIN for the current vehicle. 3. Follow the IDS prompts to read the vehicle configuration. 4. Select ‘YES’ when prompted ‘Do you wish to read diagnostic trouble codes?’. 5. Follow all on-screen instructions to complete this task. 6. Select ‘Vehicle Configuration’ tab when the ‘Content Model’ is displayed. 7. Select ‘Electronic Parking Brake’. 8. Select ‘Release to Service Position’ (S-TYPE/XJ) or ‘Parking Brake Unjam Procedure’(XK) ‘. CAUTION: When using the special service tool, take care to operate in the ‘release’ direction. Actuator motor damage may result if the tool is operated in the ‘apply’ direction for any length of time). 9. If the parking brake will not release using IDS, use the special service tool to fully release the parking brake. Refer to GTR Section ‘Parking Brake Cable Tension Release’ (in Section 206-05) for details of using the special service tool.