1988 corvette horn troubleshooting

You search PDF repair manual about 1988 corvette horn troubleshooting, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1988 corvette horn troubleshooting Direct Download speed 5432 Kb/s

  1988 corvette horn troubleshooting Full Version speed 8172 Kb/s



2000 Volkswagen Cabrio L4-2.0L Ignition Switch: Steering column, assembly Service and Repair

0

Filed Under (Volkswagen Manuals) by admin on 14-06-2011

download
1.- Horn pad -Removing, Fig. 1 2.- Horn plate -Removing, Fig. 2 3.- 50 ±10 Nm (37 ±7 ft lb) 4.- Steering wheel -Horn contact ring, Fig. 3 -Lubricate horn ring with universal grease 5.- Steering column switch securing screws 6.- Combination switch -Turn signal switch. -E2- -Headlight dimmer/flasher switch -E4- -Emergency flasher switch -E3- -Removing, Fig. 4 7.- Windshield wiper 13.- Steering lock housing -Removing and installing, refer to Steering and Suspension, Steering, Steering Column, Service and Repair 14.- Ignition/starter switch -D- -To remove, first remove steering lock housing, then remove securing screws 15.- Lock cylinder -Removing/installing, Fig. 5 16.- Spring 17.- Clamping washer Fig. 1 Horn pad, removing WARNING!Vehicles with airbags, refer to Service Precautions Vehicles without airbag – Lift horn pad at bottom and pull from steering wheel in direction of arrow. – Remove horn wire. Fig. 2 Horn plate, removing – Remove wire connector from horn plate. – Disengage retaining lugs -arrows- and remove contact plate -A- from contact plate -B-. Note: The horn plate consists of two non insulated contact plates. Horn operates when the horn pad is pressed and plate -A- contacts plate -B- .

Related Content:

2000 volkswagen cabrio repair manual download, 1989 corvette headlight problems, 2002 cabio over heating, disassemble horn on silverado, Free 1999 vw cabrio transmission Repair Manual Online, WHAT WIRES CONTROL HORN ON A 2009 C5500

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 2000 buick century service manual free, 2000 saturn sl1 owners manual, 560sl repair 1988, 2000 buick lesabre service manual pdf, 2000 coleman tacoma owners manual, diagrama buick century 2002 pmc, 2000 chevrolet suburban haynes, 2000 Chevy Impala Passkey Bypass is there a fuse

Ford 455C 555C 655C Tractor Loader Backhoe Service Manual

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Engine Systems Chapter 1 3-Cylinder Diesel Engine 3-Cylinder Diesel Engine – Description and Operation 3-Cylinder Diesel Engine – Overhaul Chapter 2 4-Cylinder Diesel Engine 4-Cylinder Diesel Engine – Description and Operation 4-Cylinder Diesel Engine – Overhaul Chapter 3 Cooling System Cooling System – 3-Cylinder Engine Description and Operation Cooling System – 4-Cylinder Engine Description and Operation Cooling System – Overhaul Chapter 4 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 2 Fuel Systems Chapter 1 Fuel System – General Fuel System – Description and Operation Fuel System – Adjustments DPA Distributor Type Fuel Injection Pump Fuel System – Adjustments DPS Distributor Type Fuel Injection Pump Fuel System – Fuel Tanks, Filters and Fuel Lines Overhaul Chapter 2 Fuel Injection Pump – DPA Distributor Type Fuel Injection Pomp – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedures Chapter 3 Fuel Injection Pump – DPS Distributor Type Fuel Injection Pump – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedure Chapter 4 Injectors Ford 455C Injectors – Description and Operation Injectors – Overhaul Chapter 5 Injectors Ford 555C and 655C Injectors – Description and Operation Injectors – Overhaul Chapter 6 Air Cleaners Dry Type Air Cleaner – Description and Operation Dry Type Air Cleaner – Overhaul Chapter 7 Turbocharger Turbocharger – Description and Operation Turbocharger – Overhaul Chapter 8 Troubleshooting, Specifications, Test Plans and Special Tools Troubleshooting – Diesel Engines Troubleshooting – Turbocharger Specifications Special Tools Test Plans Part 3 Electrical System Chapter 1 Wiring, Lights and Controls Wiring, Lights and Controls – Description and Operation Wiring, Lights and Controls – Fault Finding and Repair Circuit Diagrams and Wiring Harness Chapter 2 Battery
Battery – Description and Operation Battery – Maintenance and Tests Chapter 3 Starting System Starting System – Description and Operation Starting Motor – Overhaul Chapter 4 Charging System – A127 55 Amp Alternator with Integral Regulator Charging System – A127 55 Amp Alternator with Integral Regulator – Description and Operation Charging System – A127 55 Amp Alternator with Integral Regulator – Service Precautions, Preliminary Checks, Initial Tests and Alternator Component Tests Charging System – A127 55 Amp Alternator with Integral Regulator – Overhaul Chapter 5 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 4 Power Reversing Transmission Chapter 1 4×4 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul Chapter 2 8X8 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit, Lockup Valves and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul

Related Content:

MERCEDES BENZ KE JETRONIC FUEL SYSTEM TROUBLE TRACER, ford 550 backhoe operator manual, procedure for overhauling a gear pump, dpa injector pump govenor spring settings, ford 555c alternator wiring diagram, Lucas feul injector pump type 908 for tractor, how to repair fuel injectors on 2003 GMC Envoy, n14 cummins troubleshooting, mack 2001 fuel system, manual service unipluse f800

1991 Honda Civic Si FUSES AND CIRCUIT BREAKERS Identification

0

Filed Under (Honda Manuals) by admin on 17-05-2011

download
IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fig. 1: Fuse Panel Identification (1988-91) Courtesy of AMERICAN HONDA MOTOR CO., INC. Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) , 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Honda 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)

Related Content:

Fuse box honda pilot cigatette lighter, honda civic 09 cigarette lighter fuse, locationof2013sonicfuselocation, 2011 honda pilot fuse identification, bmxa apply chart, inside fuse box 2005 honda civic, 2007 civic main relay locations, 2012 HONDA CRV AUX FUSE LOCATION, mirrors on 2013 rav4 not auto moving fuse location, 1990 corvette intake manual removal

1987-1988 Toyota Supra EMS P/N 30-1110 Installation Manual

0

Filed Under (Toyota Manuals) by admin on 21-03-2012

download
1) Removing the Stock Engine Control Unit a) Access the stock Engine Control Unit (ECU). The location of the ECU on the Toyota Supra is behind the Glove box. b) Remove the Phillips head screw on the bottom of the glove box hinge. Remove the glove box by tilting the box at an angle from side to side and slide it toward you. c) Carefully disconnect the wiring harness from the ECU. Avoid excessive stress or pulling on the wires, as this may damage the wiring harness. Some factory ECU’s use a bolt to retain the factory connectors, and it must be removed before the harness can be disconnected. There may be more than one connector, and they must all be removed without damage to work properly with the AEM ECU. Do not cut any of the wires in the factory wiring harness to remove them. d) Remove the fasteners securing the ECU to the car body, and set it aside. Do not destroy or discard the factory ECU, as it can be reinstalled easily for street use and troubleshooting. 2) Install the AEM Engine Management System. a) Plug the factory wiring harness into the AEM ECU, and position it so that the wires are not pulled tight or stressed. Secure it with the provided Velcro fasteners. NOTE: The fourth 6 position factory connector is not used with the AEM EMS. b) Plug the comms cable into the EMS and into your PC. c) Turn your ignition on but do not attempt to start the engine. d) Upload the base calibration file (.cal) that most closely matches your vehicle’s configuration. (These files can be found in the AEMPro/Startup Calibrations/Toyota folder on your computer’s hard drive) e) Set the throttle range: Select the Configure drop down menu, then ECU Setup | Set Throttle Range and then follow the direction given on the screen. f) Verify the ignition timing by selecting the Configure drop down menu, then ECU Setup | Set Ignition. Use a timing light and compare the physical timing numbers to the Parameter Ignition Timing displayed. Use the Advance/Retard buttons to make the timing number match

1989 Toyota 4Runner ENGINE PERFORMANCE Removal Overhaul And Installation

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.

Related Content:

yhs-mystartdefault, toyota 4k carburetor manual download, remove center peice from 2011 toyota camry, how replace alternator in 2006 honda odessey, toyota sienna grill removal, how to check windshield wiper motor and arm on a 2007 malibut, how to remove center console 2013 camry, jaguar fuel hose removal, how remove intake plenum on 1998 Toyota sienna, 2005 tundra grill removal

Chevrolets Tri-Five Steering Column to Steering Box Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 01-10-2011

download
The spline in your stock steering wheel is the same as the one on the new column, so no modifications are needed here. Turn the wheel over and find two screws that hold a metal tap to the wheel. This tab is what is used to cancel your turn signals. Remove the two screws and the tab as you will not be using them with your new column. You will have to drill a 1/2″ diameter hole in the wheel 3/4″ from the center of the splined hole in the center of the steering wheel at 45° (looking at the front of the wheel). If this can’t be done because of screw holes for a puller, try to get the hole as close as possible on either side. Do not drill out puller holes, you may need them later to pull the wheel. Install horn kit, if purchased. If the horn kit with ring is purchased, the ring is to be siliconed onto the steering wheel. If it doesn’t fit on exactly right, use a file or die grinder to trim inside. (If it’s way off, call us and we may something that will fit or we can make you something that will fit.) Next, install the wheel on the column. If it doesn’t want to go on at first, move the horn cam with your thumb and index finger a little one way or the other until the wheel drops down fully. This horn cam is what cancels the turn signals, so with this horn cam at 10:30, the steering box half way between full left and right, and the road wheels pointed straight ahead, the turn signals will cancel at the right time

1989 Chevrolet Corvette V8-350 5.7L Steering Column Service and Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 08-07-2012

download
SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined. 2. Place turn signal lever to the right turn position, then remove screw and switch actuator pivot assembly (Nos. 11 and 44 in Fig. 59 ). 3. Remove the screws and the wiring protector (Nos. 10 and 45). 4. Remove turn signal switch, then gently pull wire harness through column housing shroud, column housing and lock housing cover. 5. Reverse procedure to install, noting the following: a. Torque turn signal switch screws (No. 10 in Fig. 59 ) to 27 inch lbs. and torque screw (No. 11) to 18 inch lbs. BUZZER SWITCH ASSEMBLY & STEERING COLUMN LOCK CYLINDER SET

Related Content:

2014 tundra painted bumper, gw7 steering wheel manual, tundra 2010 transmission actuator, tundra actuator repair

1988-1996 TOYOTA PICK-UP LOWER CONTROL ARMS INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
1) Park your truck on flat level surface. Chock the rear wheels. Loosen front lug nuts. Raise the front with a floo jack. Support the frame with jack stands. Remove front wheels. NOTE : ALWAYS USE JACK STANDS – NEVER RELY ON JACKS ONLY!! 2) Starting on the drivers side, locate the height adjusting bolt at the rear of the torsion bar. Measure and record the length of the threads exposed between the end of the adjusting bolt and jam nuts (Fig. A). Now make a mark at the front of the torsion bar, where it goes into the bracket bolted the lower control arm. Mark bath the bar and the bracket (Fig. B). This will index the bar into the correct position when installing. Fig. A Fig. B Note : Step #2 assumes torsion bars are in the factory position. 3) Loosen the height adjusting bolts until there is no longer any load on the torsion bars. 4) Remove the 2 bolts that hold the tensioncompression rod and sway bar end link bolts. 5) Now remove the two bolts on each arm that holds the torsion bar receiver to the back of the control arm. Slide the torsion bar and receiver back from the control arm. There is a wide spline on the torsion bar corresponding to the double width tooth on the torsion bar receiver. The receiver will not slide back onto the bar if the splines are not aligned properly. 6) Loosen and remove the 3 nuts and bolts that hold each ball joint to the lower control arms. 7) Remove the pivot bolts holding the lower control arm to the frame and remove control arm from truck. 8) Unbolt and remove original bump stops from factory arms and bolt them to you new DJM control arm. 9) Drill out the small hole on the end of the torsion bar receiver to 7/16″on both sides. This is to accept the 7/16″ x 5- 1/2″ bolt supplied. 10) Compare the new DJM control arms with the factory ones. Carefull note the diameter of the factory ball joint mounting holes. You will find either three 10mm hole used on most earlier models or larger 13mm holes on late models. If you factory arms have the 10mm holes continue to step # 10. If factory holes are 13mm it will be necessary to enlarge the holes with a 1/2″ drill bit(Fig. C). Fig. C 11) Mount the DJM control arms to the truck. Make sure the steering stops are facing the front of the truck. Insert the pivot bolts and install the washers and nuts. DO NOT TIGHTEN YET . 12) Bolt on the tensioncompression rods to the lower control arms. It mat be necessary to loosen the large nuts that hole the tensioncompression rods to the frame in order to rotate the rods to the proper angle to align bolts into control arms.

Related Content:

arm cam download

1988 Mercedes Benz 260E KE-Jetronic (CIS-E) Injection System Description and Operation Manual

0

Filed Under (Mercedes-benz Manuals) by admin on 14-02-2012

download
A mechanical hydraulic injection system provides the basis for the Bosch KE-Jetronic (CIS-E) fuel system. The mechanical portion of the CIS-E system consists of the mixture control unit (air flow meter and fuel distributor ), primary pressure regulator, fuel accumulator , cold start valve , fuel injectors, pumps, filter, lines, tank and fuel cooler . In addition, electrical controls have been added for increased flexibility to meet todays more stringent performance and exhaust emission requirements. Refer to “COMPUTERIZED ENGINE CONTROLS” for a detailed description of electronic components. Air/Fuel Metering The basic function of the KE-Jetronic system is to meter fuel to the engine dependent upon the quantity of air drawn in by the engine (which is the main actuating variable). The stream of air drawn in by the engine deflects the sensor plate, which in turn actuates the fuel-metering plunger. Depending upon its position, the plunger opens or closes the fuel-metering slits. The metering slits supply fuel through the differential pressure valves to the individual fuel injectors. In contrast to the K-Jetronic system, the KE-Jetronic system also takes a number of additional engine operating data into account by means of sensors. The output signals from these sensors are processed by the KE-Jetronic electronic control unit which controls the electro-hydraulic actuator which adapts the injected fuel quantity to the various operating conditions. In the event of a system malfunction, the KE-Jetronic system operates solely with the basic function (CIS), and the driver then has a system at his disposal which provides a good limp-home capability when the engine is warm

Related Content:

ke jetronic service manual, bosch jetronic fuel injection for saab 99 turbo, bosch k jetronic workshop manual, bosch ke jetronic function, cis-jetronic, how to adjust air flow potential k jetronic, k jetronic service manual

Related Content:

2000 volkswagen cabrio repair manual download, 1989 corvette headlight problems, 2002 cabio over heating, disassemble horn on silverado, Free 1999 vw cabrio transmission Repair Manual Online, WHAT WIRES CONTROL HORN ON A 2009 C5500