1989 cr125 power valve schematic

You search PDF repair manual about 1989 cr125 power valve schematic, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1989 cr125 power valve schematic Direct Download speed 5432 Kb/s

  1989 cr125 power valve schematic Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, youtube replace the hub on a meritor ff981 axle

1994 Toyota Paseo ENGINE IDENTIFICATION/ VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Toyota Manuals) by admin on 12-11-2011

download
1) Disconnect PCV hose, necessary electrical connections and spark plug wires to access valve cover. Remove nuts, seal washers, valve cover and gasket. 2) Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. Ensure timing mark on crankshaft pulley aligns with “0″ mark on timing belt cover. 3) Ensure valve lifters on cylinder No. 1 are loose and valve lifters on cylinder No. 4 are tight. If conditions are not as described, rotate crankshaft clockwise one complete revolution (360 degrees). 4) Using feeler gauge, measure valve clearance between valve lifter and camshaft on intake valves of cylinders No. 1 and 2, and exhaust valves of cylinders No. 1 and 3. Record valve clearance. Rotate crankshaft clockwise one complete revolution (360 degrees). 5) Measure and record valve clearance on intake valves of cylinders No. 3 and 4, and exhaust valves of cylinders No. 2 and 4. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. VALVE CLEARANCE SPECIFICATIONS TABLE (1) Application In. (mm) Exhaust Valve ………….. .012-.016 (.31-.41) Intake Valve …………… .006-.010 (.15-.25) (1) – Adjust valve clearance with engine cold. 6) If valve clearance requires adjustment, rotate camshaft so lobe on valve to be adjusted is facing upward, away from valve lifter. Position notch area on valve lifter toward inside of cylinder head. DO NOT align notch area with camshaft. Use Valve Clearance Adjuster (SST 09248-55040) to adjust valve clearance. 7) Using SST “A” of valve clearance adjuster, push downward on valve lifter. Place SST “B” between camshaft and valve lifter. See Fig. 2. Ensure enough clearance exists for adjusting shim removal. Remove SST “A”. Fig. 2: Adjusting Valve Clearance Courtesy of Toyota Motor Sales, U.S.A., Inc. 8) Using small screwdriver and magnet, remove adjusting shim. Measure and record thickness of removed shim. Using measured clearance and adjusting shim thickness, select proper replacement adjusting shim. See Figs. 4 and 5. 9) Install replacement adjusting shim. Recheck valve clearance. Apply sealant at indicated valve cover sealing areas on cylinder head. See Fig. 3. 10) Using NEW gasket, install valve cover and sealing washers. Install and tighten nuts to specification. See TORQUE SPECIFICATIONS. To install remaining components, reverse removal procedure. NEW SHIM THICKNESS TAB

Related Content:

toyota 4af valve clearance, how to replace the perge valve on a Saturn Vue, lifter replacement 2004 avalanche 5 3 engine, REPAIR MANUAL FOR KANCIL ENGINE PDF, yhs-ddc_bd, perodua kancil valve clearen instraction pdf, 2010 Honda Accord valve cover Torque Specs, 4m51 engine valve clearance, 2012 chevy cruze pcv valve, 2006 toyota tacoma 4 cyl valve cover gasket replacement

1984-1995 Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System Repair Manual

0

Filed Under (Honda Manuals) by admin on 22-04-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum. When servicing or repairing any part of the emissions system, it is absolutely essential to check for any obvious mechanical faults or failures. Remember, a trouble code only indicates which sensor or circuit is affected by the problem. Simple mechanical faults such as a vacuum leak or poor electrical connection can cause a fault code. The EGR valve is not simply open or closed but is modulated by controlling the amount of engine vacuum to the valve diaphragm, up to a maximum of 8 in. Hg of vacuum. The EGR valve has a sensor in the top of the valve that reports valve lift to the ECU (same as ECM, 1992-95). The ECU modulates the position of the control solenoid valve to control the EGR valve lift according to an internal program. Upstream of the control solenoid valve, the CVC provides a constant supply of vacuum so EGR control is precise under all manifold vacuum conditions

Related Content:

2004 honda purge control valve, clean egr valve lincoln, c230 2005 removing pcv valve and hoses, 2008 hyundai elantra purge valve, 2007 implala vent solenoid replacement, pvc valve for 2001 merc sable 24 valve overhead cam, where is the pcv valve on chevy cruze, where is the pvc valve located on a 2008 toyota tundra, egr valve chevy trailblaxer 2005, fuel purge valve for 2006 chevy impala

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, dodge durango 2002 suspension layout, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, zimmatic pivot wiring, 2003 s10 airbag wiring diagram, abs and Anti Theft Passive 2000 mercury cougar, 1996 silverado electrical manual, 2008 dodge Durango fuse box

Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System OPERATION MANUAL

0

Filed Under (Honda Manuals) by admin on 28-01-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines
SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum.

2008 Ford Focus A/T Main Control Valve Body Removal And Installation

0

Filed Under (Ford Manuals) by admin on 01-07-2012

download
Disassembly 12 7Z490 Separator plate and gasket assembly 1. Remove the solenoid body bolts and the 13 7A101 Body — control valve lower solenoid body. 14 7R294 Stop — main regulator valve 15 7F445 Retainer plate — main regulator valve 16 7A270 Spring — main fluid pressure regulator valve 17 7C338 Valve — main fluid pressure regulator 18 7G411 Spring — solenoid regulator valve 19 7H392 Valve — solenoid regulator valve 20 7D400 Spring — intermediate servo accumulator 21 7D398 Piston — intermediate servo 2. Remove and discard the solenoid body gaskets. accumulator 22 7G408 Valve — converter pressure relief 23 7G316 Spring — converter regulator valve 24 7M040 Valve — lock up control 25 7Z490 Gasket — solenoid body 26 7G179 Valve — low reverse shift 27 7M040 Valve — 3-4 shift 28 7H148 Shift Solenoid B (SSB) (on/off) valve 29 7H148 Shift Solenoid A (SSA) (on/off) valve ISASSEMBLY AND ASSEMBLY (Continued) 3. Remove and discard the seals. 3. Install the seals. 4. Disassemble the main control valve body. 4. Install a new solenoid body gasket. Assembly 1. Install a new separator plate and gasket assembly. 2. NOTE: Do not fully tighten the bolts at this stage. Assemble the main control valve body and loosely install the bolts. DISASSEMBLY AND ASSEMBLY (Continued) 5. Install the solenoid body and loosely install the 6. Tighten the solenoid body bolts in the sequence bolts. shown. •Tighten to 9 Nm (80 lb-in)

Related Content:

5R55E Valve Body manual, diagram for torque converter clutch for 2000 Venture, valve body torque specs chevy venture, how to chane the vent valve solenoid in 2008 gmc yukon, 2007 torqshift valvebody removal, how to change the vent valve seliod on a 2008 gmc, 2003 trailblazer valve body, exploded view toyota A650E valve body, free 5r55e valve body transmission gasket replacement instructions for 2001 ford explorer, how to remove sl2 bellhousing without removing valve body

1996 Ford Taurus Transmission and Drivetrain Automatic Transmission/Transaxle Removal and installation Manual

0

Filed Under (Ford Manuals) by admin on 20-04-2012

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve. Zoom Sized for Print Oil Pump And Valve Body Bolt Tightening Sequence

Related Content:

can a 2002 taurus transmission be removed without removing subframe, CLEAN THROTTLE BODY CHEVY ENVOY, how to replace the bumper cover on a 1998 Isuzu Rodeo, 03 Chevy impala removing valve cover, volvo xc90 2 9 rocker cover removal, valve cover gaskets on 2002 Escape V6, Removing Valvebody on 722 6, remove 2003 taurus transmission lowering only one side subframe, how to removed a valve body from volvo s 70, how to remove valve cover 5 4 32v navigator

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

mitsubishi canter (4D35) repair manual pdf, starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 19-05-2011

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

Related Content:

1981 chevrolet p30 motorhome brake replacement instructions, Honda service manual 1995 accord, 1995 accord repair manual pdf, 2003 buick lesabre lose power for instrument panel and a/c controls, 1989 corvette climate control panel, 2005 honda crv malfunction indicator lamp reset, fuse chart for 2002 chevy silverado 2500 no brake lights, honda accord 61-10 code, fuel circuit outputs on chevy s10, honda accord code 61-1

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

0

Filed Under (Chevrolet Manuals) by admin on 07-05-2012

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

Related Content:

acura mdx check charging system, 2006Chevyimpala4t65Echeckballlocations, how to drain the air conditioner on a 2003 jetta, manual seting sistem injection pord ranger, test circuit driver injector toyota hilux 2010 3 0 wiring diagram in pdf free, tranny fluid location 2010 santa fe, troubleshooting P069E, 4r100 rear carrier assembly colorado springs, chevy impala air conditioner flapper doesnt turn off, 2007 chevy trailblazer code c0161

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, youtube replace the hub on a meritor ff981 axle