1990 buick century service manual

You search PDF repair manual about 1990 buick century service manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1990 buick century service manual Direct Download speed 5432 Kb/s

  1990 buick century service manual Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, how to change power steering pump 2009 acada, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, how to replace 2003 impala power steering pump

ALL INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 23-04-2012

download
SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. Groan noise during stopping: • Usually caused by glazing of the rotor’s surface as a result of heavy or frequent braking. • Refer to technical bulletins specific to the model of vehicle regarding this issue. • Replace the brake pads, then resurface the rotors and finish them with sand paper. Refer to Brake Service on page 5 for additional detail. Single clunk noise from front suspension when applying the brakes: • The noise is a result of the brake pads shifting in the direction of rotor rotation when the brakes are applied. Can be duplicated by lightly touching the brake pedal. • • If the brake pedal is pushed hard, the noise is less likely to occur. Make sure the brake pads and pad hardware (shims, springs, clips, etc) are installed correctly. Refer to ASIST for vehicle specific brake service information. Refer to Brake Service on page 5 for additional detail. Mull e he engine is started: • st er models, the self check occurs the first aches 5 mph after the engine is started. ors or drums. • WARNING: Brake dust may be hazardous if inhaled. Refer to the Service Manual (ESM) for brake • n and lubrication of brake pads, CAUTION: Do not get grease on the brake pad friction surface. A • Brake Judder is caused by rotor thickness variation and/or rotor run out.

Related Content:

Free 98 Honda Accord service Repair Manual, lexus engine 2gr-fe chirping squeak noise sb0010-09, titan 5500 generator manual, manual for 1993 bmw 325i, Honda Accord 1998-2002 Service Repair Manual free PDF, 2012 f-150 service manual, 94 nissan pickup diagnose repair, motorcraftservice com, h22a service manual, Chrysler Pacifica Service Manual PDF

Acura MDX Torque Converter Shudder or Vibration Between 35 and 40 MPH Repair Manual

0

Filed Under (Acura Manuals) by admin on 24-11-2011

download
1. To confirm the client’s complaint, test-drive the vehicle on a smooth road, preferably with a slight incline. Set the cruise control between 35 and 40 mph, and monitor the engine rpm using the vehicle’s tachometer, or use the HDS to take a snapshot of the engine rpm. 2. If the engine speed fluctuates several hundred rpm while maintaining a constant vehicle speed, disconnect the EGR valve and retest the vehicle. •If the fluctuation is gone, refer to the EGR troubleshooting in the service manual. •If the engine rpm still fluctuates, and the transmission does not have any other symptoms (shifting problems, slipping, transmission DTCs) go to step 3. 3. Drain the transmission fluid, then strain it through a paint strainer. •If you find little or no contamination in the strainer, the ATF is OK, even if it smells burnt, is discolored, and/or the magnetic drain plug has small chips, flakes, or metal fuzz on it. Go to REPAIR PROCEDURE A . •If you find large amounts of contamination (pieces of metal or friction material) in the strainer, go to REPAIR PROCEDURE B . REPAIR PROCEDURE A 1. Remove the torque converter: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Install the torque converter: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 3. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 4. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are off. •Start the engine, and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes. REPAIR PROCEDURE B Follow the IN-WARRANTY EXCHANGE steps in service bulletin 90-009, Automatic Transmission In- Warranty Exchange Program , to order a remanufactured A/T, replace the failed A/T, and return the failed A/T core. 1. Remove the transmission: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Clean the transmission cooler. Refer to service bulletin 89-015, ATF Cooler Cleaner . 3. Install a remanufactured transmission: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 4. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 5. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off. •Start the engine and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes

Related Content:

1998 mazda MPV owners manual, 2002 ford thunderbird service manual, freelander engine control module mobility module master, how much for torque converter for 2001 mdx, torque converter problems symptoms for 1999 3 2tl acura, what is a torque shudder

Honda Navigation System Information and DVD Information and Inspection Manual

0

Filed Under (Honda Manuals) by admin on 06-07-2012

download
REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system

Related Content:

manual lincoln navigator 2007, reset liftgate lincoln, exploded view 4r55e, service manual for civic 2007, 2005 odyssey service manual free, 2003 honda odyssey service manual, c1998 module calibration failure navigator 2006, invision revolution dvd manual, hubsan x4 manual pdf, lincoln navigator 1998 fuses oxygen

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

Honda Clunk or Squeak From Rear Suspension Repair Manual

0

Filed Under (Honda Manuals) by admin on 15-02-2012

download
REPAIR PROCEDURE NOTE: ISIS online service manual information is only available for vehicles 1990 and newer. 1. Remove the rear trailing arm: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword REAR SUSPENSION, then select Suspension Arms Replacement from the list. 2. Mark the trailing arm at the arrow on the bottom of the bushing 3. Place the arm on a hydraulic press, supported by the hub base, with the spindle facing up. 4. With the hub driver, press the old bushing out of the trailing arm. 5. Install the new bushing with the short end toward the outside of the vehicle. Align the arrow with the mark you made on the trailing arm. 6. Press the new bushing into the trailing arm until its edge is 10 to 12 mm above the surface of the arm. 7. Reinstall the trailing arm. 8. If necessary, repeat steps 1 thru 7 to install a new bushing in the other rear trailing arm. 9. Bleed the brake system: •Refer to the brakes section of the appropriate service manual, or •Online, enter keyword BLEED, then select Brake System Bleeding from the list. 10. Check the wheel alignment, and adjust it if needed: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword WHEEL ALIGNMENT, then select Wheel Alignment – Rear Toe Inspection/Adjustment from the list

Related Content:

how 2002 install mountaineer rear trailing arm, removing rear torque arm on 97 buick century

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 200lolds aleroraditor system, schematic for front brakes on 2005 Buick Rendezvous, w584a lincoln, 2007 Chevy Colorado Gas Tank Seal replace, pontiac 2007 g6 remove radiator cover, 4t65e service manual online, 2007 kia rio service manual

1997 Buick Century Limited 3.1/ 3.4L COLD ENGINE TICK OR RATTLE AFTER START-UP (REPLACE PISTON/ PIN ASSEMBLY)

0

Filed Under (Buick Manuals) by admin on 03-01-2012

download
Some customers may comment on a ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. CAUSE Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur. This level of noise does not affect the reliability or durability of the product. CORRECTION If piston-to-pin noise is detected and the customer desires the condition to be corrected, replace all six pistons with pin assemblies. The new piston sets have a minimal piston-to-pin clearance. Remember, piston-to-pin noise occurs in both park and drive at engine idle rpm and it varies in intensity depending on the number of pistons involved. A ticking sound means one piston is affected whereas a rattle or diesel type sound indicates more than one piston affected. The following should also be checked: 1. On W-Cars, make sure the right side engine splash shield is not contacting the engine crankshaft balancer. This condition usually happens cold and is caused by the shield curling when cold. 2. Reference Service Bulletin 57-71-06 for transmission rattle noise often confused for engine rattle noise. 3. Reference Service Bulletin 47-61-36 for Accessory Drive Belt Tensioner noise. 4. Check cylinder bore diameter and piston diameter as outlined in the Service Manual. Use the procedure in the appropriate Service Manual for piston replacement. Service Bulletin 57-61-24 (Section 6 – Engine). NOTE: Excessive cylinder bore to piston diameter clearance can cause a similar type noise. NOTE: When installing the new piston and pin assembly onto the existing rods, use extreme care to avoid damage to either the pin or piston bore. If damage to these areas occurs, the noise will return because the damage will cause wear and excessive clearance

Related Content:

toe reference diameter, 07 FUSO P0560, 08 escalade esv lifter noise, 1999 Buick Century rattleing noise, 2000 buick park ave making ratting car makes rattling, gm 3800 noises, popping niose front on 1997 buick lesabra, what could cause a ticking in an 1993 buick regal engine

2004-2005 FORD F-150 FRONT BRAKE ROUGHNESS/ SHUDDER WHILE BRAKING REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 10-06-2012

download
ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.

Related Content:

2004 dodge dakota repair manual free download, 2004 Cavalier Repair Manual PDF, change rotors 94 explorer, change rotors on 94 explorer 4x4, copy of 2004 chevy truck mannual, fender passport p 150 service manual, honda pilot 2004 repair manual, how to replace rotors on 2005 f250, MINN ROTOR THICKNESS 04 SEBRING, service manual 2004 chevrolet pdf

Single Speed Axle Service Manual

0

Filed Under (More Manuals) by admin on 27-05-2012

download
Figure 1-1 Spicer axles are identified with a manufacturing date and complete part numbers stamped on the right- hand tube. The part number may also appear on a metal tag attached to the cover plate by the cover screws, depending upon the requirements of the vehicle manufacturer. The part number, consisting of six digits reading from left to right, is the basic number for identifying the particular axle assembly. The seventh digit following the dash will identify ratio, differential, and end yoke options used in the assembly. The next group of numbers is the manufacturing date of the axle and is interpreted as follows. The first number is the month, the second number is the day of the month, the third number is the year, the fourth is the line that built the axle, and the letter is the shift. NOTE It is recommended that when referring to the axle, the complete part number and build date be obtained. To do this, it may be necessary to wipe or scrape off dirt, etc., from the axle housing. If the axle is unique on design such that the unit cannot be identified in the standard manner as described above, refer to the vehicle manufacturer’s service and/or parts manual for proper identification. SERVICING COMPONENTS NOT COVERED IN THIS MANUAL Service procedures for some components may not be covered in this manual because they are unique to the vehicle application. Refer to the vehicle manufacturer’s service manual for servicing those components. (e.g. brakes, hubs, rotors, and wheel end components). VEHICLE STORAGE OR PROLONGED INOPERATION If the vehicle has not been operated on a regular daily basis, it is recommended that the vehicle be operated at least once every two weeks. The vehicle should be moved far enough to cause the drivetrain components to make several complete revolutions. This procedure will help assure that all internal components receive adequate amount of lubrication to help reduce component deterioration caused by an undesirable environment (e.g. high humidity).

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, how to change power steering pump 2009 acada, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, how to replace 2003 impala power steering pump