Skip to content

1990 chevy 3500 wiring diagram

You search PDF repair manual about 1990 chevy 3500 wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

1992 Toyota Cressida Wiring Diagram

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

REV / SPEED METER Vehicle Specific Wiring Diagram Installation

download
Installation Precautions ?Do not use electro taps in the installation of this product. Electro taps can become loose over time causing the unit to malfunction. This can also lead to vehicle and product damage. Be sure to use wire crimpers and the included splices for a secure connection. ?Be sure that the harness is not exposed to metal. Always wrap all connections with electrical tape. ?How to use the Fittings Strip 5mm from wire Insert sleeve over wire Bend back exposed wire Place male fitting over This ECU terminal arrangement diagram is viewed from the direction of the arrow. The direction of the ECU varies depending upon the vehicle. Perform the installation work after confirming the connector shape and the number of pins. ?If any abnormal noise or abnormal smell is sensed during the installation work of this product stop the work immediately and contact the distributor or your nearest A*PEX business office Continuing the installation under such conditions may cause an electric shock or fire causing damage to electric devices.

Toyota ISO Adapter Wiring Diagram

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

1998 Chevrolet Chevy K Pickup DTC P1626 Theft Deterrent Fuel Enable Signal Not Received Repair Manual

download
An intermittent may be caused by any of the following conditions: Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems. Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This test checks if communication can be established between the scan tool and the VTD. If the scan tool cannot communicate with the VTD, refer to Diagnostic System Check – Theft Deterrent in Theft Deterrent. 3. This test checks for any opens in the serial data circuit between the VCM and the VTD. This also checks for any intermittent malfunctions associated with the serial data circuit. 4. This step is to determine if the condition that set the DTC is still present. The engine must be cranked in order to set this DTC. If the condition is present, the engine will start and then stall, indicating the VCM is disabling fuel. 7. Use a scan tool to clear and check for any DTCs in all the modules connected to the Class 2 Serial Data circuit (VCM, VTD, ATC, and BCM). the module itself. After repairing the cause of DTC P1626, clear all DTCs from the systems capable of storing this DTC and DTC U1192. 1 Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module’s data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the scan tool. 2. Turn ON the ignition leaving the engine OFF. 3. Attempt to establish communications with the VTD (Passlock) Control Module. Does the scan tool communicate with the VTD (Passlock) Control Module? — Go to Step 3 Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent 3 Check the Class 2 Serial Data circuit for the following intermittent conditions: Did you find a problem? • An open in the Class 2 Serial Data circuit between the VCM and the VTD (Passlock) Control Module. • A short to ground. • A short to voltage. • Loose or damaged terminals at the DLC, VCM or the VTD (Passlock) Control Module. — Go to Step 6 Go to Step 4 4 1. Turn OFF the ignition. 2. Connect or install any connectors or components that were disconnected or removed. 3. Clear all DTCs using a scan tool. 4. Turn OFF the ignition for 15 seconds. 5. Attempt to start the engine. Does DTC P1626 reset? — Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent Go to Step 5 5 This DTC is intermittent. Are any additional DTCs stored? — Go to the applicable DTC table Go to Diagnostic Aids 6 Repair the circuit as necessary. Refer to Wiring Repairs or Connector Repairs in Wiring Systems. Is the action complete?