1991 dodge dakota wiring diagram

You search PDF repair manual about 1991 dodge dakota wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1991 dodge dakota wiring diagram Direct Download speed 5432 Kb/s

  1991 dodge dakota wiring diagram Full Version speed 8172 Kb/s



2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, zimmatic pivot wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, 2003 s10 airbag wiring diagram, dodge durango 2002 suspension layout, 97 jetta fuel pump wiring diagrams, 1996 silverado electrical manual

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

Related Content:

1983 monte carlo window wiring, 2005 ford ficm connector view, 3406e 1lw 40 pin wire, elect repair for cadillac dashboard replacement, kia besta wiring diagram, PIN DATA 2005 скачать, toyota alphard wiring diagram, vp44 9 pin connector, what pins are positve and negative on a 40 pin cat ecm

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

1991-1994 FORD TEMPO VEHICLE WIRING

0

Filed Under (Ford Manuals) by admin on 26-05-2012

download
WIRING INFORMATION: 1991 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 1992 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Doo

Related Content:

1999 CHEVY SILVERADO DRIVER MIRROR MOTOR installation Instructions, 2003 pontiac vibe installing a 2 wire push button, 2002 lincoln town car driver side door expanted view, 2008 chevy driver door switch wiring schmatic, 1999 cadillac deville drivers seat diagram, 04 impala driver side window regulator diagram, driver\s junctio nbox 2 accord 2012, drivers side front door on a 2002 mercury marquis wont close, honda cr-v drivers side armrest, drivers side window repair 2001 Dodge Dakota

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix, igt savp parts diagram

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, location of mode motor for 99 honda civic lx, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2001 DODGE RAM 2500 OWNERS MANUAL, 2005 honda pilot blend control motor, 2001 chevy malibu cruse control fuse

Hemi Chrysler 300C, Dodge Magnum and Dodge Charger Installation instructions

0

Filed Under (More Manuals) by admin on 06-12-2011

download
Installation instructions: 1. Raise and support vehicle. 2. Lubricate factory rubber hangers with penetrating oil. 3. Remove fasteners attaching driver side tailpipe/resonator assembly to rear of center-mount factory muffler. Remove tailpipe/resonator from factory hangers and from vehicle. 4. Loosen stock clamps attaching stock exhaust to converter pipe outlets near front of vehicle. 5. Remove black factory stiffener cross-brace from bottom of vehicle. 6. With a helper, remove factory hanger rods from rubber hangers and remove remaining exhaust system from vehicle. 7. Place two supplied clamps over inlets of X-pipe and install assembly over outlets of factory converter pipes. The X- pipe should be installed to position the slotted-hole brackets towards the top of the pipes. Do not fully tighten clamps at this time. 8. Using two supplied clamps, install mufflers over outlets of X-pipe assembly. Do not fully tighten clamps at this time. 9. Using two supplied clamps, install left and right tailpipes to outlets of mufflers and insert hanger rods into factory rubber hangers. Do not fully tighten clamps at this time. 10. Install tips with clamps over outlets of tailpipes. 11. Reinstall factory body stiffener brace to bottom of vehicle. 12. Starting at front of vehicle, align system and tighten clamps. You may need to push system upwards while tightening clamps to be sure system adequately clears stiffener brace. 13. Align tips and tighten clamps .

Related Content:

free owners manual for dodge intrepid 2001, 1996 Dodge Intrepid Owners Manual pdf, 1996 dodge ram 1500 owners manual free download, 1999 dodge ram wagon 1500 owner manual, dodge d50 service manual free, 97 caravan repair manual pdf download free, cadillac DTC PO622, Dodge Charger 2 7 Firing Order, 1500 dodge ram wagon 1999 owner manual, install directions for dodge 2500 ac unit

Toyota Corolla Upgrading a car radio

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

download
step 1: Preparing the wiring harness Get a wiring harness or adapter that will allow the car radio wiring to plug into the back of the new radio. These can be found at Walmart for $4.99. Make sure that the plug is compatible with your car (check the list on the back of the box). Have shown the back of the new radio – the black set of pins is where the included black plug will go to. The free wires on the black plug provided with the new audio system will be connected to an adapter that will plug into the car wiring. For the Toyota Corolla 1995 wagon, the wiring diagram is as shown below. Your car may differ substantially from this step 2: Connecting the wires Connect the wires from the plug that came with the new radio to the wiring harness adapter that you purchased separately. Twist the correct wires together and then solder them (or use wire nuts if you dot have soldering equipment). Cover the exposed wire with electricians tape or heat seal tape. Attached is another table on how you connect your Toyota wiring adapter to the radio plug. Please, do remember that your radio and car will differ a bit step 3: Removing the old radio Remove the factory installed radio (the instructions apply only for Corollas from 95-98). Remove the two screws below the panel. Have shown a picture with the location of these screws. Remove the control knobs for the AC and the fan, etc. These come off pretty easily with a gentle pull. Use a thin blade (metal spatula) to probe approximately 2/3rd of the way up and try to pry the sides out. The metal blade will disengage the clip on each side. Took a bit of gentle effort but it did pop out. The location of these clips is just below the vents. Lift the panel up, reach under it to carefully remove the plugs on the right hand side that connect the defroster, the clock and the hazard flasher. The plugs can be removed by squeezing a release tab on the plug and then gently pulling them apart. Remove the radio – two pairs of screws on each side of the radio hold it in place. Remove these (and hold onto them because you will need them later on) and then slide the radio out.

1991 Honda Civic Si FUSES AND CIRCUIT BREAKERS Identification

0

Filed Under (Honda Manuals) by admin on 17-05-2011

download
IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fig. 1: Fuse Panel Identification (1988-91) Courtesy of AMERICAN HONDA MOTOR CO., INC. Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) , 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Honda 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)

Related Content:

Fuse box honda pilot cigatette lighter, honda civic 09 cigarette lighter fuse, locationof2013sonicfuselocation, 2011 honda pilot fuse identification, bmxa apply chart, inside fuse box 2005 honda civic, 2007 civic main relay locations, 2012 HONDA CRV AUX FUSE LOCATION, mirrors on 2013 rav4 not auto moving fuse location, 1990 corvette intake manual removal

1991 Saab 9000 L4-2290cc 2.3L DOHC Turbo EFI Axle Shaft Removal And Installation Manual

0

Filed Under (Saab Manuals) by admin on 04-06-2012

download
Service and Repair Notes Removal Important: Thorough cleanliness must be observed during all work on drive shafts and drive shaft joints, to prevent dirt and dust getting into the joints. Before starting work, always clean the wheel arch, MacPherson strut and other areas around the drive shaft and joints. 1Unfasten the hub centre-nut. 2Lift the car and remove the wheel. 3Remove the hub centre-nut. Push the axle stub back approx. 2 cm (if it pushed further back it can damage the tripod). Use puller 87 91 287 and puller arms 87 91 303 together with tool 87 91 154, puller bracket, the belongs to tool collection for manual gear boxes. 4Remove the steering-swivel member from the MacPherson strut and unfasten the flexible hose from the hose mounting and, if appropriate, also unfasten the ABS sensor and cable. Important: Scrupulously clean the rubber gaiter and the universal joint driver. 5Remove the clamp securing the rubber gaiter on the inner universal joint driver. Pull the universal joint apart and fit the protective cover on the rubber gaiter and universal joint driver. 6Pull out the drive shaft from the hub. Fitting 1Remove existing grease out of the universal joint driver and carefully clean the interior. 2 Pack the universal joint driver with grease, 60 g Mobile K 575 GS. Observe great cleanliness. Motor / ALLDATA Online – 1991 Saab 9000 L4-2290cc 2.3L DOHC T… http://www.motoralldata.com/alldata/MOTOR~V71595976~C19965~… 3 of 4 3/26/2008 12:03 AM Zoom Sized for Print

Related Content:

haynes saab 9-3 pdf download

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, zimmatic pivot wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, 2003 s10 airbag wiring diagram, dodge durango 2002 suspension layout, 97 jetta fuel pump wiring diagrams, 1996 silverado electrical manual