Skip to content

1991 ford econoline van wiring diagram ignition

You search PDF repair manual about 1991 ford econoline van wiring diagram ignition, if there are search results will appear below. If search results do not exist, please search by others keyword.

1991-1994 FORD TEMPO VEHICLE WIRING

download
WIRING INFORMATION: 1991 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 1992 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Doo

1992 Toyota Cressida Wiring Diagram

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Toyota ISO Adapter Wiring Diagram

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

1989-1996 Dodge Dakota Trucks COIL Ignition Tests Manual

download
Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: • 1989-92 engines: mounted to the firewall • 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor • 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head • 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket. Fig. 2: Ignition coil mounting-all 1989-92 models Fig. 3: Ignition coil wiring and mounting hardware-1993- 96 2.5L engine 1. Inspect the ignition coil for arcing while the engine is running. If the engine will not start, this can be performed while the engine is cranked by either an assistant or a remote starter. Look at the coil in dim or low light to aid visibility of any arcing. Fig. 4: Ignition coil mounting-1993-96 3.9L and 5.2L/5.9L LDC engines 2. Arcing at the tower will carbonize the wire boot, which, if it is connected to a new ignition coil, will cause the coil to fail. In such cases, clean all the carbonization away or replace the components as necessary. Fig. 5: Ignition coil mounting-1993-96 5.9L HDC engine 3. Using a coil tester or ohmmeter according to the manufacturer’s instructions, test the primary and secondary resistance. Replace any coil that does not meet the specifications indicated in the accompanying chart. 4. Inspect the secondary coil wire for any sign of damage. Replace if any damage is found. Carbon tracking on the old wire can cause arcing and the failure of a new ignition coil. REMOVAL & INSTALLATION 1989-92 Models See Figures 6 and 7 1. Disconnect the negative battery cable. 2. Disconnect the three wires from the coil. Mark them to identify for installation. Fig. 6: Remove the coil bracket bolt at the cowl Fig. 7: Unscrew the coil mounting hardware, then remove the coil from the vehicle 3. Unplug the condenser suppressor connector from the coil, if equipped. 4. Unbolt and remove the coil. To install: 5. Bolt down the coil with old bolts. 6. Connect wires to coil making sure that the proper wires are connected where they should be. 7. Connect the condenser suppressor, if equipped. 8. Connect the battery negative cable Removal and Installation V6 AND V8 ENGINES 1. Disconnect the negative battery cable. 2. Disconnect the primary wiring from the ignition coil. 3. Disconnect the secondary spark plug wire from the coil. 4. Remove the two bolts and withdraw the coil from its mounting bracket. To install:
5. Position the coil on its bracket and install the two bolts. Tighten them to 100 inch lbs. (11 Nm). If the bracket has been tapped for coil mounting bolts, these fasteners require less torque, so tighten them to 50 inch lbs. (5 Nm). 6. Connect all wiring to the ignition coil. TESTING See Figure 1 The only test you can perform without a DRBII scan tool, or equivalent, is a basic check of the sensor only.