Skip to content

1991 mercedes r129 driver seat control switch mounting clips

You search PDF repair manual about 1991 mercedes r129 driver seat control switch mounting clips, if there are search results will appear below. If search results do not exist, please search by others keyword.

1994 Ford Town Car/ Crown Victoria/ Grand Marquis Trim Panels, Door Removal And Installation Manual

download
Trim Panels, Door Front Town Car The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification. Removal CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove. 1. Snap out two door pull strap retaining screw covers. Remove screws. 2. Remove two screws on front and rear side of front door trim panel. 3. Using the Trim Pad Removing Tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent, pry the trim panel retaining clips from the door inner panel. NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins. 4. Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors. 5. Disconnect driver seat regulator control processor switch (driver door only) if equipped. 6. Twist out interior lamp wire assembly and remove the front door trim panel. Installation 1. Ensure plastic watershield is secured to door panel. 2. Position front door trim panel to door. Connect interior lamp wiring. 3. Position the window regulator control switch housing and connect switch connectors. 4. Connect driver seat regulator control processor (14C708) (driver door only) if equipped. 5. Align door lock side to its mating slide on the sheet metal (front doors only) 6. Snap in front door trim panel . Ensure all retainers fit properly. 7. Install two retaining screws on front and rear side of front door trim panel . 8. Install two retaining screws and pull strap covers. Removal 1. Remove outside rear view mirror remote control unit. 2. Remove window regulator control switch housing by gently prying up, starting at the front. 3. Disconnect all connectors from window regulator control switch housing. 4. Remove inside door handle cup (22634) by gently prying at screwdriver slot with a screwdriver. 5. Remove push pin from front door trim panel upper front extension and remove screw. 6. Remove lower self-tapping screw retaining front door trim panel to door inner panel. 7. On Grand Marquis only, pry up screw covers from door pull handle and remove screws and handle. 8. Lift front door trim panel upward and snap out trim panel. 9. Disconnect wire harnesses from door panel as required and remove front door trim panel . Installation 1. Connect wire harnesses to front door trim panel as required. 2. Install front door trim panel by pushing in and down until it snaps into place. 3. Install all self-tapping screws retaining front door trim panel to door inner panel. 4. On Grand Marquis only, install door pull handle, tighten screws and install screw covers. 5. Install push pin covering screw on trim panel upper front extension. 6. Install inside door handle cup . 7. Install window regulator control switch housing.

1998 Ford F 150/250 Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

download
Instrument Panel Removal 1. If equipped with power seats, move the seat fully rearward. 2. Remove the passenger air bag. For additional information, refer to Section 501-20B . 3. Remove the driver air bag. For additional information, refer to Section 501-20B . 4. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal. Carefully pry to release the (A) clips and remove the (B) steering column opening cover. 5. Position the electrical connector aside. * Release the push clip from the lower instrument panel steering column cover (044F08). 6. Pull to release the three (A) clips and remove the (B) fuse door. 7. Position the hood latch release handle aside. 1. Remove the screws. 2. Position the hood latch release handle aside. 8. Position the parking brake release handle aside. 1. Remove the screws. 2. Position the parking brake release handle aside. 9. If equipped, remove the instrument panel floor duct panel. * Remove the two push clips and release the expander clip. 10. Remove the lower instrument panel steering column cover (04459). 1. Remove the bolts. 2. Remove the lower instrument panel steering column cover. 11. Remove the LH and RH scuff plates. 12. Remove the LH and RH cowl side trim panels. 13. Disconnect the brake pedal position (BPP) switch electrical connector. 14. Remove the (A) radio ground and the (B) GEM/CTM ground bolts. 15. Disconnect the LH instrument panel main harness connectors. 16. Remove the bulkhead wiring harness electrical connectors from inside the engine compartment. 1. Loosen the bolts. 2. Disconnect the bulkhead electrical connectors. 17. Remove the bulkhead electrical connector from the dash panel. 1. Release the six locking tabs. 2. Remove the bulkhead connector from the dash panel. 18. Disconnect the air bag diagnostic monitor electrical connectors. 19. Disconnect the inertia fuel shutoff switch electrical connector. 20. Remove the RH ground bolts. 21. Disconnect the RH instrument panel main harness connectors. 22. Disconnect the electronic blend door actuator electrical connector. 23. Disconnect the climate control head vacuum harness connector. 24. Remove the instrument panel steering column opening cover reinforcement (04502). 1. Remove the nuts. 2. Remove the instrument panel steering column opening cover reinforcement. 25. Disconnect the air bag sliding contact electrical connectors and the anti-theft sensor electrical connector.

Wiring Toyota Switch to SH-R-00 Carbon Fiber Seat Heater

download
Wiring Toyota Switch to SH-R-00 Carbon Fiber Seat Heater (Switch is ready to use with FWSH-U-00 FlexWire Seat Heater) SH-R-EXT (rev 0) Harness plug: Black, White, Red, Green Toyota Switch Pigtail CarbonFiber Harness Extn To use the Toyota Switch with SH-R-00 Carbon Fiber Seat Heater kit, you will need to direct connect the wires, eliminating the modular plugs on both the harness extension and switch. 1. Cut the plug end off the Toyota switch pigtail harness. 2. Cut the end plug off the wire harness extension. 3. Attach spade connectors to each wire. 4. Cross connect the wires as shown. 5. Test switch before mounting

Renault Laguna II A195 Door function control module driver

download
Battery – 30 Battery + A195 Door function control module, driver A196 Door function control module, passenger M27 Door mirror adjustment motor, driver M28 Door mirror adjustment motor, passenger S98 Door mirror adjustment switch EP10Earth point location 10 EP4 Earth point location 4 EP5 Earth point location 5 EP9 Earth point location 9 M14 Electric window motor, driver M15 Electric window motor, passenger S64 Electric window switch, driver’s door S65 Electric window switch, passenger door F Fuse X28-IIFuse box/relay plate, engine bay X28-IFuse box/relay plate, fascia 1 K79 Ignition main circuits relay 15 Ignition switch – ignition ON A11 Multifunction control module X92 Shorting link connector bl = blue br = brown el = cream ge = yellow gn = green gr = grey nf = neutral og = orange rs = pink rt = red sw = black vi = violet ws = white hbl = light bluehgn = light green rbr = maroon x = braided cabley = high tensionz = non-cable connection NOTE: In certain diagrams (Citroen, Peugeot & Renault), colour codes are replaced by numbers which are used to identify a particular cable and not the colour. In this instance, the cables will be numbered at each end close to the harness connector.

1991 Honda Civic Si FUSES AND CIRCUIT BREAKERS Identification

download
IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fig. 1: Fuse Panel Identification (1988-91) Courtesy of AMERICAN HONDA MOTOR CO., INC. Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) , 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Honda 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)