1992 buick lesabre manual pdf

You search PDF repair manual about 1992 buick lesabre manual pdf, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1992 buick lesabre manual pdf Direct Download speed 5432 Kb/s

  1992 buick lesabre manual pdf Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, how to replace 2003 impala power steering pump, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

0

Filed Under (Buick Manuals) by admin on 04-02-2012

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

Related Content:

buick terraza hub removal, 2005 buick century code p0455, hunter 9700 user manual, 2000 buick lesabre custom manual, how to change the lower control arms on a 2005 Titan pdf, hunter lift L401, integrated wheel end FOR F150, location of fuses and relays 2003 buick park avenue, Rear Tire wear Mecury Mariner, repair manual on 2001 cadi deville on motor mount

1993 Dodge Dakota FUSE PANEL IDENTIFICATION

0

Filed Under (Dodge Manuals) by admin on 24-05-2011

download
3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights. 9 – 15 Amp (Lt. Blue) Cigarette Lighter. 10 – 20 Amp (Yellow) Windshield Washers & Wipers. 11 – 20 Amp (Yellow) Turn Signals, Rear Wheel Anti-Lock Module. 12 – 10 Amp (Red) Radio. 13 – 4 Amp (Pink) Cluster Lights, A/C & Heater Controls, Cigarette Lighter Light & Ash Receiver Light, Radio Lights & Overdrive Switch Light. 14 – Not Used (1992-93); 15 Amp (Lt. Blue) (1994-95 Airbag Module, Speedometer, Gauges, Telltales. 15 – 2 Amp (Gray) Speed Control. 16 – 5 Amp (Tan) Gauges & Indicator Lights: Low Oil Light, Low Washer Light, Service Reminder Light, Transmission Oil Light, Brake Warning Light, Anti-Lock Brake Warning Light, Fuel Pacer Light, 4WD Indicator Light, Malfunction Indicator Light, Warning Buzzer, Overdrive Switch (1992-93); Transmission Oil Temperature Lamp, 4WD Lamp, Overdrive Module Seat Belt Warning Buzzer (1994-95). 17 – (Blank) Not Used. 18 – (Blank) Not Used. 19 – (Blank) Not Used. 20 – Not Used (1992-93); 25 Amp (Natural) (1994-95) Fog Lamps and Off Road Lamps. 21 – Turn Signal Flasher No additional definition. 22 – Time-Delay Relay No additional definition. 23 – Horn Relay No additional definition. 24 – Hazard Flasher No additional definition. 25 – Warning Buzzer

Related Content:

emission light on impala, 86 ford ranger emission sensors, 2011 dodge durango not charging, 1992 CHEVrolet silverado idle air control assembly calibration specifications, 1992 Grand Marquis Manual, mazda 3 transmission gear indicator light, service 4wd light on silverado, Isuzu NPR Warning Light Icons, slip light on nissan titan, how to reset washer fluid malibu 06

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

0

Filed Under (Ford Manuals) by admin on 15-05-2012

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

Related Content:

0761 emission code ford, repair manuel 91 suburu loyle, manual webasto pdf, manual lever position sensor troubleshooting, free download jo8c parts book, ford ranger transmission repair manual, ford five hundred repair manual 2007 pdf, 86 ford ranger repair manual, 2004 ford ranger owners manual pdf, wiring for a zemmadic 410 pivot

Honda Navigation System Information and DVD Information and Inspection Manual

0

Filed Under (Honda Manuals) by admin on 06-07-2012

download
REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system

Related Content:

manual lincoln navigator 2007, reset liftgate lincoln, exploded view 4r55e, service manual for civic 2007, 2005 odyssey service manual free, 2003 honda odyssey service manual, c1998 module calibration failure navigator 2006, invision revolution dvd manual, hubsan x4 manual pdf, lincoln navigator 1998 fuses oxygen

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 2006 ford focus ses repair manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, cft30 scan codes, 1999 chevy S10 - manual, 95 ford Windstar 3 8 change transmission shifter cable, 1999 cavalier A/C instructions, 95 ford ranger owners mqnual, 1998 ford escort auto repair manual free

1996 Ford Taurus Transmission and Drivetrain Automatic Transmission/Transaxle Removal and installation Manual

0

Filed Under (Ford Manuals) by admin on 20-04-2012

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve. Zoom Sized for Print Oil Pump And Valve Body Bolt Tightening Sequence

Related Content:

can a 2002 taurus transmission be removed without removing subframe, CLEAN THROTTLE BODY CHEVY ENVOY, how to replace the bumper cover on a 1998 Isuzu Rodeo, 03 Chevy impala removing valve cover, volvo xc90 2 9 rocker cover removal, valve cover gaskets on 2002 Escape V6, Removing Valvebody on 722 6, remove 2003 taurus transmission lowering only one side subframe, how to removed a valve body from volvo s 70, how to remove valve cover 5 4 32v navigator

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

Related Content:

free download Service Manual for a 1992 Toyota Truck, Toyota 5K ignition, _1987_Nissan_pickup_v6 destributer timing marks

How to bypass the VATS (PASSKey II) system in a late model GM vehicle

0

Filed Under (More Manuals) by admin on 16-09-2011

download
Pontiac 1994-1996 Grand Prix 1992-1999 Bonneville 1993-2002 Firebird/Trans Am/Firehawk Buick 1994-1996 Regal 1992-1999 LeSabre 1991-1996 Park Avenue 1991-1996 Roadmaster Oldsmobile 1994-1997 Cutlass Supreme 1992-1999 Eighty Eight/LSS/Ninety Eight/Regency 1991-1996 Custom Cruiser Wagon Chevrolet 1995-1999 Monte Carlo 1995-2001 Lumina 1993-2002 Camaro 1986(?)-1996 Corvette (C4) Cadillac How to bypass the VATS system in a late model GM vehicle Bullet-Style” solderless connectors Heat Shrink Tubing Resistors of varying values (totalling the resistance measured across the key’s “pellet”) Alright, let’s begin the madness: 1. Take your DMM, set it to measure Ohms (use the 20k setting.) Measure the resistance across the pellet of the ignition key. Place one probe on the silver part of one side of the pellet, and the other probe on the other side. Write this value down. 2. Purchase a resistor or resistors that add up to the value measured in step 1. Radio Shack is a great place to go for the resistors, heat shrink tubing, and the “bullet-style” solderless connectors. 3. Take the 16 ga. wire and cut into 2 four-inch pieces. 4. Strip off approx 1/16″ of insulation off each side of both wire pieces. 5. Put your resistors together in series (or if you’re lucky and have a chip that has a resistance that matches a single resistor) and solder one wire to one end of the resistor(s) and the other wire to the other side. Example: You measure 11.72 on the 20k (k meaning kilo or 1,000) scale. The closest match is 11.801 which is a #15 “chip.” Always remember that resistors have a tolerance of 2%, meaning the resistance value of the “pellet” can be either 2% higher or 2% lower than 11.801 k ohms (11.72 falls in tolerance range.) You will want to aim for 11,801 ohms. So when you go to Radio Shack you want to pick up a 10,000 ohm (10k,) a 1,000 ohm (1k,) and an 800 ohm resistors to wire together in series to achieve the 11.801k ohm value.

Related Content:

07 colorado passlock, vats key modgler location 1996 pontiac bonneville, vat for 1996 park avenue, pics of vat\s wire on 1994 corvette, p1349 bmw 530i 2003, how do I replace the VATS module on a 1997 buick lesabre, bypass vats on a 1997 buick lesabre, 99 lesabre vats bypass resistor, 1993 corvette vats bypass, 1993 corvett icm bypass

2000 Chevy Truck S10/T10 Blazer Transfer Case Removal And Installation Manual

0

Filed Under (Chevy Manuals) by admin on 18-05-2011

download
Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case. 12. For vehicles equipped with a manual transmission, remove the six nuts securing the transfer case and bracket to the transmission 13. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 14. For vehicles equipped with a automatic transmission, remove the six nuts securing the transfer case and bracket to the transmission adapter. 15. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 16. Remove and discard the gasket. Installation Procedure 1. Install a new gasket to the transmission. Use sealer GM P/N 12346004 in order to hold the gasket in place. 2. Raise and position the transfer case to the vehicle Notice: Refer to Fastener Notice in Service Precautions. 3. For vehicles equipped with a automatic transmission, install the six nuts securing the transfer case and bracket to the transmission adapter. * Tighten the nuts to 47 Nm (35 lb ft) . 4. For vehicles equipped with a manual transmission, install the six nuts securing the transfer case and bracket to the transmission. * Tighten the nuts to 47 Nm (35 lb ft)

Related Content:

wiring for case w20 loader, case 444-75 repair manuals free, How to rebuild Kia Sorento Transfer Case, Case 1845C Manual Download, np 208 service manual, toyota tacoma ground wire transfer case, Chevy NP208 Rebuild Instructions, 2001 ford sports trac 4x4 transfer case wiring diagram, f150 transfer case problems, ford 2003 ford explorer how transfer case works

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, how to replace 2003 impala power steering pump, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle