1993 dodge dakota wiring diagram

You search PDF repair manual about 1993 dodge dakota wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1993 dodge dakota wiring diagram Direct Download speed 5432 Kb/s

  1993 dodge dakota wiring diagram Full Version speed 8172 Kb/s



2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, zimmatic pivot wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, 2003 s10 airbag wiring diagram, dodge durango 2002 suspension layout, 97 jetta fuel pump wiring diagrams, 1996 silverado electrical manual

1989-1996 Dodge Dakota Trucks COIL Ignition Tests Manual

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: • 1989-92 engines: mounted to the firewall • 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor • 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head • 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket. Fig. 2: Ignition coil mounting-all 1989-92 models Fig. 3: Ignition coil wiring and mounting hardware-1993- 96 2.5L engine 1. Inspect the ignition coil for arcing while the engine is running. If the engine will not start, this can be performed while the engine is cranked by either an assistant or a remote starter. Look at the coil in dim or low light to aid visibility of any arcing. Fig. 4: Ignition coil mounting-1993-96 3.9L and 5.2L/5.9L LDC engines 2. Arcing at the tower will carbonize the wire boot, which, if it is connected to a new ignition coil, will cause the coil to fail. In such cases, clean all the carbonization away or replace the components as necessary. Fig. 5: Ignition coil mounting-1993-96 5.9L HDC engine 3. Using a coil tester or ohmmeter according to the manufacturer’s instructions, test the primary and secondary resistance. Replace any coil that does not meet the specifications indicated in the accompanying chart. 4. Inspect the secondary coil wire for any sign of damage. Replace if any damage is found. Carbon tracking on the old wire can cause arcing and the failure of a new ignition coil. REMOVAL & INSTALLATION 1989-92 Models See Figures 6 and 7 1. Disconnect the negative battery cable. 2. Disconnect the three wires from the coil. Mark them to identify for installation. Fig. 6: Remove the coil bracket bolt at the cowl Fig. 7: Unscrew the coil mounting hardware, then remove the coil from the vehicle 3. Unplug the condenser suppressor connector from the coil, if equipped. 4. Unbolt and remove the coil. To install: 5. Bolt down the coil with old bolts. 6. Connect wires to coil making sure that the proper wires are connected where they should be. 7. Connect the condenser suppressor, if equipped. 8. Connect the battery negative cable Removal and Installation V6 AND V8 ENGINES 1. Disconnect the negative battery cable. 2. Disconnect the primary wiring from the ignition coil. 3. Disconnect the secondary spark plug wire from the coil. 4. Remove the two bolts and withdraw the coil from its mounting bracket. To install:
5. Position the coil on its bracket and install the two bolts. Tighten them to 100 inch lbs. (11 Nm). If the bracket has been tapped for coil mounting bolts, these fasteners require less torque, so tighten them to 50 inch lbs. (5 Nm). 6. Connect all wiring to the ignition coil. TESTING See Figure 1 The only test you can perform without a DRBII scan tool, or equivalent, is a basic check of the sensor only.

Related Content:

ciol wire problems 2007 camry, priceofcoylepackfora2005kiasedona, chevy 230 cid primary resistor, no power to coil on 1993 dakota, test coil dodge dakota 1993, Isuzu 1997 wiring diagram between coil distibutor, Remove Evap coil from honda element, 1996 dodge dakota 2 5 temperature sensor diagram, replace individual coils on 2002 mercury mountaineer, replacing evaporator on 1999 gmc truck

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

Related Content:

1983 monte carlo window wiring, 2005 ford ficm connector view, 3406e 1lw 40 pin wire, elect repair for cadillac dashboard replacement, kia besta wiring diagram, PIN DATA 2005 скачать, vp44 9 pin connector, what pins are positve and negative on a 40 pin cat ecm

1993 Dodge Dakota FUSE PANEL IDENTIFICATION

0

Filed Under (Dodge Manuals) by admin on 24-05-2011

download
3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights. 9 – 15 Amp (Lt. Blue) Cigarette Lighter. 10 – 20 Amp (Yellow) Windshield Washers & Wipers. 11 – 20 Amp (Yellow) Turn Signals, Rear Wheel Anti-Lock Module. 12 – 10 Amp (Red) Radio. 13 – 4 Amp (Pink) Cluster Lights, A/C & Heater Controls, Cigarette Lighter Light & Ash Receiver Light, Radio Lights & Overdrive Switch Light. 14 – Not Used (1992-93); 15 Amp (Lt. Blue) (1994-95 Airbag Module, Speedometer, Gauges, Telltales. 15 – 2 Amp (Gray) Speed Control. 16 – 5 Amp (Tan) Gauges & Indicator Lights: Low Oil Light, Low Washer Light, Service Reminder Light, Transmission Oil Light, Brake Warning Light, Anti-Lock Brake Warning Light, Fuel Pacer Light, 4WD Indicator Light, Malfunction Indicator Light, Warning Buzzer, Overdrive Switch (1992-93); Transmission Oil Temperature Lamp, 4WD Lamp, Overdrive Module Seat Belt Warning Buzzer (1994-95). 17 – (Blank) Not Used. 18 – (Blank) Not Used. 19 – (Blank) Not Used. 20 – Not Used (1992-93); 25 Amp (Natural) (1994-95) Fog Lamps and Off Road Lamps. 21 – Turn Signal Flasher No additional definition. 22 – Time-Delay Relay No additional definition. 23 – Horn Relay No additional definition. 24 – Hazard Flasher No additional definition. 25 – Warning Buzzer

Related Content:

emission light on impala, 86 ford ranger emission sensors, 2011 dodge durango not charging, 1992 CHEVrolet silverado idle air control assembly calibration specifications, 1992 Grand Marquis Manual, mazda 3 transmission gear indicator light, service 4wd light on silverado, Isuzu NPR Warning Light Icons, slip light on nissan titan, how to reset washer fluid malibu 06

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix, igt savp parts diagram

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, location of mode motor for 99 honda civic lx, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram, Hino 268 2013 fuse box for heater location

1994 Cadillac DeVille Concours Procedure to Disable Illumination of Service Indicator AFTER the Installation of Passive Struts/Shocks

0

Filed Under (Cadillac Manuals) by admin on 11-06-2011

download
Run a wire from a switched ignition (hot in Run) source to relay pin 85. 1992-1993 Oldsmobile Achieva with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1992-1994 Buick Skylark with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1993-1996 Buick Park Avenue with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1991-1995 Oldsmobile Ninety Eight with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1994-1999 Pontiac Bonneville with Computer Command Ride (CCR) The feedback strut/shock assemblies are still available for these vehicles. However, if the customer desires to reduce the repair expense, the following steps may be taken to allow installation of non-feedback assemblies and the disabling of the malfunction indicator lamps. This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. Parts Information The following parts are required to make the correction on the 1993 Eldorado/Seville and the 1994-1995 DeVille. Parts are currently available from GMSPO

Related Content:

1993 cadallic deveal service manuel, 1992 park avenue repair manual, 1993 cadillac deville no pressure, 1994 buick century repair manual pdf, 1999 buick park avenue repair manual free pdf, buick park avenue 1992 repair manual, fix ac in 1995 sudan deville, program vin to computer 1999 cadillac deville, where is the vats computer on a 1994 cadillac deville

Hemi Chrysler 300C, Dodge Magnum and Dodge Charger Installation instructions

0

Filed Under (More Manuals) by admin on 06-12-2011

download
Installation instructions: 1. Raise and support vehicle. 2. Lubricate factory rubber hangers with penetrating oil. 3. Remove fasteners attaching driver side tailpipe/resonator assembly to rear of center-mount factory muffler. Remove tailpipe/resonator from factory hangers and from vehicle. 4. Loosen stock clamps attaching stock exhaust to converter pipe outlets near front of vehicle. 5. Remove black factory stiffener cross-brace from bottom of vehicle. 6. With a helper, remove factory hanger rods from rubber hangers and remove remaining exhaust system from vehicle. 7. Place two supplied clamps over inlets of X-pipe and install assembly over outlets of factory converter pipes. The X- pipe should be installed to position the slotted-hole brackets towards the top of the pipes. Do not fully tighten clamps at this time. 8. Using two supplied clamps, install mufflers over outlets of X-pipe assembly. Do not fully tighten clamps at this time. 9. Using two supplied clamps, install left and right tailpipes to outlets of mufflers and insert hanger rods into factory rubber hangers. Do not fully tighten clamps at this time. 10. Install tips with clamps over outlets of tailpipes. 11. Reinstall factory body stiffener brace to bottom of vehicle. 12. Starting at front of vehicle, align system and tighten clamps. You may need to push system upwards while tightening clamps to be sure system adequately clears stiffener brace. 13. Align tips and tighten clamps .

Related Content:

free owners manual for dodge intrepid 2001, 1996 Dodge Intrepid Owners Manual pdf, 1996 dodge ram 1500 owners manual free download, 1999 dodge ram wagon 1500 owner manual, dodge d50 service manual free, 97 caravan repair manual pdf download free, cadillac DTC PO622, Dodge Charger 2 7 Firing Order, 1500 dodge ram wagon 1999 owner manual, install directions for dodge 2500 ac unit

1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Timing Belt: Service and Repair Manual

0

Filed Under (Mitsubishi Manuals) by admin on 23-01-2011

download
.Removal of crankshaft pulley. Using special tools remove the crankshaft pulley from the crankshaft. CAUTION: -Use only the specified special tools, or a damaged pulley damper could result. 10.Removal of engine support bracket. Remove the engine support bracket in the numbered sequence shown in the illustration. Spraying lubricant, slowly remove the bolt (reamer bolt) indicated by the arrow. CAUTION: -Keep in mind that the reamer bolt is sometimes heat seized on the engine support bracket. 12.Removal of timing belt. (a)Align the timing marks.
1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 8.80 Page 3 (b)Make a mark on the back of the timing belt indicating the direction of rotation so it may be reassembled in the same direction it it is to be reused. (c)Loosen the center bolt on the tensioner pulley to remove the timing belt. CAUTION: -Water or oil on the belt shorten its life drastically, so the removed timing belt, sprocket, and tensioner must be free from oil and water. These parts should not be washed. Replace parts if seriously contaminated. If there is oil or water on each part check the front case oil seals, camshaft oil seal and water pump for leaks. 1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 13.Installation of auto tensioner. (a)If the auto tensioner rod is in its fully extended position, reset it as follows:1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 8.80 Page 5 1)Keep the auto tensioner level and, in that position. clamp it in the vise with soft jaws. 2)Push in the rod little by little with the vise until the set hole (A) in the rod is aligned with that (B) in the cylinder. CAUTION: -Push in the rod slowly to prevent the push rod from being damaged. 3)Insert a wire [1.4 mm (0.055 in.) in diameter] into the set holes. 4)Unclamp the auto tensioner from the vise. (b)Install the auto tensioner. CAUTION: -Leave the wire installed in the auto tensioner. 12.Installation of timing belt. (a)Align the timing marks on the respective sprockets. In case of the camshaft sprockets in the front bank, proceed as follows: 1)Install the crankshaft pulley. Shift the timing mark on the crankshaft sprocket by three teeth to lower the piston in No. 1 cylinder slightly from the top dead center on compression stroke. CAUTION: -Turning the camshaft sprocket with the piston in No.1 cylinder located at TDC on compression stroke may cause the valves to interfere with the piston

Related Content:

case 446 repair manual, 1993 bmw 525i owners manual, 1993 corvette vats, 1993 infiniti g20 repair manual, Free Mitsubishi 3000GT Repair Manual, remove optic park in 93 vette, removing camshaft sprocket 3000 gt, renew vss sensor, video of oil pump install for 3000gt

1993-1998 Toyota Supra TT EMS P/N 30-1100 Installation Manual

0

Filed Under (Toyota Manuals) by admin on 20-03-2012

download
Read and understand these instructions BEFORE attempting to install this product. 1) Removing the Stock Engine Control Unit a) Access the stock Engine Control Unit (ECU). The location of the ECU on the Toyota Supra is under the passenger firewall carpet and has a black cover that is removed by 4 10 mm nuts. b) Carefully disconnect the wiring harness from the ECU. Avoid excessive stress or pulling on the wires, as this may damage the wiring harness. Some factory ECU’s use a bolt to retain the factory connectors, and it must be removed before the harness can be disconnected. There may be more than one connector, and they must all be removed without damage to work properly with the AEM ECU. Do not cut any of the wires in the factory wiring harness to remove them. c) Remove the fasteners securing the ECU to the car body, and set it aside. Do not destroy or discard the factory ECU, as it can be reinstalled easily for street use and troubleshooting. d) Make sure any aftermarket electronics are COMPLETELY and properly removed before starting the vehicle. 2) Install the AEM Engine Management System. a) Plug the factory wiring harness into the AEM ECU, and position it so that the wires are not pulled tight or stressed. Secure it with the provided Velcro fasteners. b) Plug the comms cable into the EMS and into your PC. c) Turn your ignition on but do not attempt to start the engine. d) Upload the base calibration file (.cal) that most closely matches your vehicle’s configuration. (These files can be found in the AEMPro/Calibrations/Toyota folder on your computer’s hard drive) e) Set the throttle range: Select the Configure drop down menu, then ECU Setup | Set Throttle Range and then follow the direction given on the screen f) Verify the ignition timing by selecting the Configure drop down menu, then ECU Setup | Set Ignition . Use a timing light and compare the physical timing numbers to the Parameter Ignition Timing displayed. Use the Advance/Retard buttons to make the timing number match. 3) You are now ready to begin tuning your vehicle. a) Note: This calibration needs to be properly tuned and is not recommended for street use. NEVER TUNE YOUR VEHICLE WHILE DRIVING.

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, zimmatic pivot wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, 2003 s10 airbag wiring diagram, dodge durango 2002 suspension layout, 97 jetta fuel pump wiring diagrams, 1996 silverado electrical manual