Skip to content

1993 mercedes 190e repair manual free download

You search PDF repair manual about 1993 mercedes 190e repair manual free download, if there are search results will appear below. If search results do not exist, please search by others keyword.

1993 Mercedes Benz 190E Drive Belt Tensioner Service and Repair Manual

download
Service and Repair Notes NOTE : The belt tensioning device has been modified during production, tensioner version may vary from one vehicle to another. Early engines may be retrofit with later tensioners but requires additional parts. PROCEDURE Remove Poly V-Belt . On Tensioning Devices Without Shock Absorber NOTE : The 1st design of the tensioning device was without a shock absorber. Unbolt fixing bolt (25). Tightening torque: With 19mm hex head 75 Nm (55 ft lbs) . With 17mm hex head 80 Nm (59 ft lbs) . Remove belt tensioner.

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly

1990 TOYOTA SUPRA REPAIR MANUAL DOWNLOAD

download
INTRODUCTION MAINTENANCE ENGINE MECHANICAL wi EXHAUST SYSTEM TURBOCHARGER SYSTEM EMISSION CONTROL SYSTEMS EFI SYSTEM COOLING SYSTEM LUBRICATION SYSTEM IGNITION SYSTEM STARTING SYSTEM CHARGING SYSTEM CLUTCH MANUAL TRANSMISSION AUTOMATIC TRANSMISSION PROPELLER SHAFT FRONT AXLE AND SUSPENSION REAR AXLE AND SUSPENSION BRAKE SYSTEM STEERING SRS AIRBAG BODY ELECTRICAL SYSTEM BODY AIR CONDITIONING SYSTEM he procedures are presented in a step-by-step format: 0 The illustration shows what to do and where to do it. 0 The task heading tells what to do. 0 The detailed text tells how to perform the task and gives other information such as specifications and warnings. Example: , Task heading: what to do r’ 21. CHECK PISTON STROKE OF OVERDRIVE BRAKE (a) Place SST and a dial indicator onto the overdrive brake piston as shown in the figure. SST 09350-30020 (09350-06 1 20) Set pah No. Component part No. I I /’ Detailed text: how to do task I I (b) Measure the stroke applying and releasing the compressed air (4 – 8 kg/cm2, 57 – 114 psi or 392 – 785 kPa) as shown in the figure. Piston stroke: 1.40 – 1.70 mm (0.0551 – 0.0669 in.) Specification This format provides the experienced technician with a FAST TRACK to the information needed. The upper case task heading can be read at a glance when necessary, and the text below it provides detailed information. Important specifications and warnings always stand out in bold type. REFERENCES References have been kept to a minimum. However, when they are required you are given the page to refer to. SPECIFICATIONS Specifications are presented in bold type throughout the text where needed. You never have to leave the procedure to look up your specifications. They are also found in Appendex A, for quick reference. CAUTIONS, NOTICES, HINTS: CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other people. NOTICES are also presented in bold type, and indicate the possibility of damage to the components being repaired. HINTS are separated from the text but do not appear in bold. They provide additional information to help you efficiently perform the repair

1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Timing Belt: Service and Repair Manual

download
.Removal of crankshaft pulley. Using special tools remove the crankshaft pulley from the crankshaft. CAUTION: -Use only the specified special tools, or a damaged pulley damper could result. 10.Removal of engine support bracket. Remove the engine support bracket in the numbered sequence shown in the illustration. Spraying lubricant, slowly remove the bolt (reamer bolt) indicated by the arrow. CAUTION: -Keep in mind that the reamer bolt is sometimes heat seized on the engine support bracket. 12.Removal of timing belt. (a)Align the timing marks.
1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 8.80 Page 3 (b)Make a mark on the back of the timing belt indicating the direction of rotation so it may be reassembled in the same direction it it is to be reused. (c)Loosen the center bolt on the tensioner pulley to remove the timing belt. CAUTION: -Water or oil on the belt shorten its life drastically, so the removed timing belt, sprocket, and tensioner must be free from oil and water. These parts should not be washed. Replace parts if seriously contaminated. If there is oil or water on each part check the front case oil seals, camshaft oil seal and water pump for leaks. 1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 13.Installation of auto tensioner. (a)If the auto tensioner rod is in its fully extended position, reset it as follows:1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 8.80 Page 5 1)Keep the auto tensioner level and, in that position. clamp it in the vise with soft jaws. 2)Push in the rod little by little with the vise until the set hole (A) in the rod is aligned with that (B) in the cylinder. CAUTION: -Push in the rod slowly to prevent the push rod from being damaged. 3)Insert a wire [1.4 mm (0.055 in.) in diameter] into the set holes. 4)Unclamp the auto tensioner from the vise. (b)Install the auto tensioner. CAUTION: -Leave the wire installed in the auto tensioner. 12.Installation of timing belt. (a)Align the timing marks on the respective sprockets. In case of the camshaft sprockets in the front bank, proceed as follows: 1)Install the crankshaft pulley. Shift the timing mark on the crankshaft sprocket by three teeth to lower the piston in No. 1 cylinder slightly from the top dead center on compression stroke. CAUTION: -Turning the camshaft sprocket with the piston in No.1 cylinder located at TDC on compression stroke may cause the valves to interfere with the piston