Skip to content

1995 nissan maxima repair manual free

You search PDF repair manual about 1995 nissan maxima repair manual free, if there are search results will appear below. If search results do not exist, please search by others keyword.

NISSAN Altima, Quest, Maxima MIL ON WITH P0340 / P0345 (CMP SENSOR) AND/ OR ENGINE IS HARD TO START WHEN WARM REPAIR MANUAL

download
ACTIONS: • If you only have DTC P0340, replace only Bank 1 CMP (Camshaft Position) Sensor. • If you only have DTC P0345, replace only Bank 2 CMP (Camshaft Position) Sensor. • If you have both codes, replace both sensors. • For a “hard to start warm” incident, replace both sensors, even if you have no codes. Refer to sections EC and EM in the correct Service Manual for sensor replacement information. If replacement of the sensors does not solve your incident, go back to ASIST for further diagnostic and repair information. PARTS INFORMATION DESCRIPTION PART # QUANTITY Camshaft Position Sensor- Bank 1 23731-6J906 1 Camshaft Position Sensor- Bank 2 23731-AL616 1 CLAIMS INFORMATION Submit a Primary Failed Part (PP) line claim using the following claims coding: DESCRIPTION PFP OP-CODESYSDIAFRT RPL One Camshaft Position Sensor (Bank 1 or Bank 2) (1) DE64AA AA 32 (2) RPL Both Camshaft Position Sensors (Banks 1 and 2) (1) DE67AA AA 32 0.3 hrs. (1) Reference the Parts Information table and use the indicated sensor P/N’s as the PFP. (2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT

NISSAN ALTIMA OR SENTRA W /QR25 ENGINE NO-START AFTER COLD SOAK REPAIR MANUAL

download
SERVICE PROCEDURE Replace Starter, Add Cleaner 1. Replace the starter motor. • Use the part number from the Parts Information section of this bulletin. • Refer to section SC, “STARTING SYSTEM, Removal and Installation” in the applicable Nissan Electronic Service Manual (ESM). 2. Add one full can of Nissan In-Tank Fuel System Cleaner to the fuel. NOTE: If the fuel tank is less than ¾ full, instruct the customer to fill the tank as soon as it is convenient after the repair. Driving with the Cleaner installed and low fuel level will not harm the fuel system or engine, but will reduce the effectiveness of the cleaning process. 3. Continue to ECM Part Number Check (next page). 1. With CONSULT-II “ON”, print the Self-DIAG Results as follows: START (Nissan) >> ENGINE >> Self-DIAG Results >> PRINT SELF-DIAG RESULTS SYSTEM ENGINE DATE XX/XX/XXXX* 11:07:11 P/N 23710-XXXXX TP020389h DTC RESULTS TIME NO DTC IS DETECTED Current ECM Part Number * Example, your screen may differ. 3. Using the printout from Step 1: • Compare the vehicle’s current ECM P/N to those shown under Current ECM P/N in Chart 1, below: • This comparison will allow you to determine if the ECM needs to be reprogrammed. Chart 1, Current ECM P/N’s: VEHICLE PACKAGE NATS? CURRENT ECM P/N A/T, ASCD YES 23710-9J305, -9J003, -9J002, -9J001, -9J000, -8J001, -8J000 M/T, ASCD YES 23710-9J315, -9J013, -9J012, -9J011, -9J010, -8J061, -8J060 A/T, no ASCD YES 23710-9J300, -9J008, -9J007, -9J006, -9J005, -8J011, -8J010 02-04 Altima M/T, no ASCD YES 23710-9J310, -9J018, -9J017, -9J016, -9J015, -8J071, -8J070 YES 23710-8U542, -8U541, -8U540, -8U041, 8U040 A/T NO 23710-8U502, -8U501, -8U500, -8U001, 8U000 YES 23710-8U562, -8U561, -8U560, -8U061, -8U060 02-03 Sentra 5 M/T NO 23710-8U512, -8U511, -8U510, -8U011, -8U010 YES 23710-8U072, -8U071, -8U070 02 Sentra 6 M/T NO 23710-8U022, -8U021, -8U020 YES 23710-8U572, -8U571, -8U570 03 Sentra 6 M/T NO 23710-8U522, -8U521, -8U520 NOTE: The 2004 Sentra ECM does not need to be reprogrammed for this bulletin. A. If your vehicle’s ECM P/N matches a P/N in the chart above: • Perform ECM Reprogramming (page 4). B. If your vehicle’s ECM P/N does not match a P/N in the chart above: • ECM Reprogramming is not necessary, bulletin complete / end here

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

1999 NISSAN MAXIMA NO START AND SECURITY LAMP ON WITH NATS DTC “ID DISCORD, IMM-ECM” REPAIR MANUAL

download
SERVICE PROCEDURE NOTE: This procedure is described using CONSULT-II. CONSULT may also be used to perform the diagnostic procedures outlined below. However, the screens and steps will differ slightly from those shown here. 1. Install the NATS card (purple) into slot 1 of CONSULT-II (see Figure 1). Figure 1 2/9 2. Connect CONSULT-II to the vehicle (see Figure 2). Figure 2 3. Turn the ignition switch to “ON” (do not start the engine). CONSULT-II will then turn on automatically (see Figure 3). Now touch “START”. Figure 3 4. Select “NATS V2.0″ (see Figure 4). Figure 4
3/9 5. Select “SELF DIAGNOSIS” (see Figure 5). Figure 5 6. Confirm Self Diagnosis Result “ID DISCORD, IMM-ECM” displayed on the CONSULT-II screen (see Figure 6). Figure 6 7. Press “COPY” to print the Self-Diagnosis screen (see Figure 6). Attach this printout to the repair order. Then press “BACK” (see Figure 6) to return to the CONSULT-II main menu. 4/9 8. Turn the vehicle’s ignition switch “OFF” and CONSULT-II “OFF” (see Figure 7). Figure 7 9. Remove the NATS (purple) card from CONSULT-II and install the Diagnostics (blue) card (see Figure 8). Figure 8 5/9 10.Turn the ignition switch to “ON” (do not start the engine). CONSULT-II will then turn on automatically (see Figure 9). Now touch “START”. Figure 9 11.Select “ENGINE” (see Figure 10). Figure 10 6/9 12.Select “ECM PART NUMBER” (see Figure 11). Figure 11 13.Press “COPY” to print the ECM PART NUMBER screen (see Figure 12). Attach this printout to the repair order . Then press “BACK” to return to the CONSULT-II main menu. Figure 12 7/9 14.Turn the vehicle’s ignition switch “OFF” and CONSULT-II “OFF”. 15.Compare the vehicle’s ECM PART NUMBER as printed from CONSULT-II in step 13 to the ECM # in the chart below.

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly