1996 chevy truck k1500 heater diagram

You search PDF repair manual about 1996 chevy truck k1500 heater diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1996 chevy truck k1500 heater diagram Direct Download speed 5432 Kb/s

  1996 chevy truck k1500 heater diagram Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, location of mode motor for 99 honda civic lx, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram, Hino 268 2013 fuse box for heater location

2000 Chevrolet Blazer HEATER CORE Removal And Installation Procedure

0

Filed Under (Chevrolet Manuals) by admin on 20-05-2011

download
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE . 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws Courtesy of GENERAL MOTORS CORP. 3. Remove the heater core access cover. 4. Remove the heater core from the heater/vent module. Fig. 15: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the heater core to the heater/vent module Fig. 16: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. 2. Install the heater core access cover. Tighten Tighten the heater core access cover screws to 1.9 N.m (17 lb in). NOTE: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre

TOYOTA TACOMA DC XSB RETRACTABLE HARD TRUCK BED COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
STEP 1: POSITIONING CANISTER Remove the top cover from the canister box and set it aside for later installation. Perform a quick inventory to insure all parts are there. Be sure to check inside the small cardboard box for parts. Remove the Canister from the box and set it in the truck bed against the cab. The canister should be resting on the canister end plates and be centered in the truck bed. DO NOT USE A KNIFE TO OPEN THE RAIL BOX. OPEN THE RAIL BOX ALONG THE LENGTH OF THE BOX AND LIFT RAILS OUT TO AVOID SCRATCHING THE SURFACE OF THE RAILS ON THE PACKAGE STAPLES. CAUTION! Canister End Plates INSTALLATION INSTRUCTIONS Slide the four (4) Inner Rail Clamps (2 on each side) through the Tie Down Bars of the truck. (Figure 2B) Place the Outer Angled Rail Clamps on the Inner Rail Clamps (MAKE SURE THE NARROWER EDGE IS DOWN ON THE OUTER ANGLED RAIL CLAMPS) loosely fasten the clamps in place with the 1/4″ Washer, 1/4″ Lock Washer and Rail Clamp Nut on both sides of the truck bed. The fi rst clamp should be placed about 6 inches from the canister (closest to truck cab). The second clamp assembly should be about 4 inches from the end of the Tie Down Bar (closest to the tailgate). Open the rail box along the length of the box, lift rails out to avoid scratching the rail surface on the package staples. The side rails are marked “left” and “right” (left is the driver’s side of the truck). Then Slide Rail Clamp Bracket A on each Rail followed by Rail Clamp Bracket B. Rail Clamp Bracket A should be closest to the Cab of the truck. At this time you will need to install the taligate end of the pull strap to the underside of the drivers side rail using the #8-32 x 3/4 machine screw that is already located at the tailgate end on the underside of the rail. (Figure 2A) Now, with the tailgate closed, place the side rails in position on the truck bed with the Rail Clamp Brackets A & B resting on the Outer Angled Rail Clamps. Loosely assemble the Rail Clamp Brackets to the Outer Angled Rail Clamps with the 1/4″ Washer, 1/4″ Lock Washer and 1/4-20 x 1/2″ Bolt on each side of the truck bed. Center the Rails in the Truck bed. Check spacing in the truck bed between the Left and Right Rails. Spacing should be 51 3/4″. Once correct spacing is achieved tighten the Rail Clamp Brackets A & B only in place Correct spacing to the tailgate should be 1/16″ to prevent the tailgate from striking the side rails when closing. Tighten the Set Screws on both Rail Clamp Bracket A to hold rails in position. ( Adjust spacing from the tailgate by moving rails forward or backward as needed prior to fi nal tightening of set screws .) Apply downward pressure while tightening the Outer Angled Rail Clamp to the Inner Rail Clamp, especially on the tailgate end. This will ensure a tight seal, fi rm seat, and good fi t on the truck bed

Related Content:

Tail Gate mounting Instructions on A25 Volvo Truck, 1954 f100 owners manual, hino truck repair manual, how to install cross rails on buick enclave, instructions on how to install roof rack cross rails on a 2014 Buick Enclave, isuzu npr dashboard guide, Isuzu NPR PRNDL inoperative, kia sedona frame structure, manual 1993 s10 truck, repair Evap soleniod for 2006 chevy 1500

1996 – 2000 Civic 2-door Front Windows Bind or Have Come Out of the Run Channel Repair Manual

0

Filed Under (Honda Manuals) by admin on 10-02-2012

download
REPAIR PROCEDURE 1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual. 2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator. 3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot. 4. Check the year and VIN. If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5. If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8. 5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts. 6. Disconnect the power window motor connector, and detach the harness clip (if applicable); then lift and remove the regulator through the opening in the door. 7. Install the new regulator in the door, then loosely install the two rear mounting bolts and the two roller guide bolts. Do not tighten the two front mounting bolts yet. Go to step 9. 8. Loosen the window regulator’s two rear mounting bolts, two front mounting bolts, and two roller guide bolts

Related Content:

1996 4l60e transmission manual, 1996 suburban alarm problem, Installing Window Guide Clips, 92 crownline manuals, 1996 suburban alarm bypass, 1996 sl2 help, 1996 SL1 manaul, 1996 saturn instlation, 1996 nissan pickup ac digram, 1996 coleman crank

FORD 4-PANEL With New Automatic Latch System Truck WITH Factory Tailgate Lock CLASS 3 Installation Manual

0

Filed Under (Toyota Manuals) by admin on 10-04-2012

download
1) Clean rail surfaces really well with denatured alcohol and make sure they are dry. 2) Press Gasket down firmly the entire length of the gasket 1) Use thin foam double stick tape to hold the clamped hardware in place on inside side rails. The reason we suggest you use this foam is that it is just an extra added protection to keep your clamped hardware from shifting on the sometimes slick surface of some sprayed-in bedliners. • ALL HARDWARE PROVIDED: Stainless steel nuts (18) Part # 9723 or 9723-A – Low Profile Cast aluminum “C” Clamps (16 of them) The only difference with 9723 and 9723-A is that A is a little deeper “C” clamp which is required on some trucks because of the way the inside rail is made. These cast aluminum “C” clamps uninstalled are about the size of a 1 dollar coin and about ¾ inch thick. Part # 9724-T : Latch Installation Tape – (4 pcs.) Part # 9724 – Latch Catch Bracket (4) – These are angled pieces of metal that give your cover’s latches something to “latch to” and are installed with “C” clamps. Part # 9731 – Center Latch Catches (2) Part # 9736 – D Shaped Seals (2) – Described Above Part # 9714 or 9758 – Stainless Steel Screws (18) (Depending on “C” clamps required above) Part # ST-114 – Keyhole Bracket (2) (Mounted at the Hinge closest to the cab of the truck on the inside of the side rail of the truck at that hinge point). Part # 9727 – Box Seal (2) – Described above INSTALLATION OVERVIEW: 1) Measure and make your marks for your masking tape to put your gaskets on each side. 2) Put down masking tape the entire length of the truck 3) Follow masking tape and install peel and stick gaskets (don’t trim in the rear just yet). 4) Place cover onto truck (you will use the measurements provided to make sure the cover is located exactly in the right position 5) Install Keyhole Bracket (holds the 3rd Leg Hinge) Explanation of 3rd Leg Hinge : • 3rd Leg hinge is a flap of metal that is integrated into the hinge • This flap is on the first hinge right behind the cab of the truck • When you mount the cover, this flap hangs straight down, and slides right into the keyhole bracket 6) Install two “C” Clamps to each Keyhole bracket to secure to the truck 7) Install your stainless steel bolt with lock nut that secures the 3rd Leg Hinge (the flap) into the keyhole bracket on each side. That is “your” permanent point of attachment. (THESE ARE THE SAME TWO BOLTS THAT YOU REMOVE TO TAKE OFF THE COVER) *Remember, the cover is now “installed” and cannot slide around – so you MOUNT ALL THE HARDWARE TO FIT THE COVER from here on out 8) Attach center latch catch on inside of side rails using “C” Clamps. *Center Latch Catch: holds center hinge and the 2 panels in the middle down when the cover is closed. When you close the last panel flat onto the tailgate, a stainless steel “button” along each side of the cover is depressed between the 2 panels at the hinge. When this button is squeezed, it actually pushes a stainless steel latch towards the front of the truck catching the center latch on each side rail. 9) Attach Rear Latch Catch Brackets* using “C” Clamps * These are angled pieces of metal that give your cover’s latches something to “latch to” and are installed with “C” clamps. 10) Install Front Latch Catch Brackets using “C” clamps 11) THIS STEP IS ONLY FOR THE Ford F250/F350 SuperDuty Installations ONLY: The outer seal that comes with your cover and is attached on this rail is called a “Side Box Seal” Because the plastic Ford rails on the SuperDuty are ridged/grooved a little deeper and wider than those on the other Ford trucks, a set of small matte black screws are used in addition to the adhesive on the seal to ensure a snug fit. These screws only slightly penetrate the plastic side rail cover and do not come in contact with the underlying metal side rail

Related Content:

2001 toyota tundra tailgate piano hinge installation, liftgate latch stuck how to change spark plugs on ford expedition, remove outer handle 2014 ford fusion, stuck hood latch 2002 ford f150

1988-1996 TOYOTA PICK-UP LOWER CONTROL ARMS INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
1) Park your truck on flat level surface. Chock the rear wheels. Loosen front lug nuts. Raise the front with a floo jack. Support the frame with jack stands. Remove front wheels. NOTE : ALWAYS USE JACK STANDS – NEVER RELY ON JACKS ONLY!! 2) Starting on the drivers side, locate the height adjusting bolt at the rear of the torsion bar. Measure and record the length of the threads exposed between the end of the adjusting bolt and jam nuts (Fig. A). Now make a mark at the front of the torsion bar, where it goes into the bracket bolted the lower control arm. Mark bath the bar and the bracket (Fig. B). This will index the bar into the correct position when installing. Fig. A Fig. B Note : Step #2 assumes torsion bars are in the factory position. 3) Loosen the height adjusting bolts until there is no longer any load on the torsion bars. 4) Remove the 2 bolts that hold the tensioncompression rod and sway bar end link bolts. 5) Now remove the two bolts on each arm that holds the torsion bar receiver to the back of the control arm. Slide the torsion bar and receiver back from the control arm. There is a wide spline on the torsion bar corresponding to the double width tooth on the torsion bar receiver. The receiver will not slide back onto the bar if the splines are not aligned properly. 6) Loosen and remove the 3 nuts and bolts that hold each ball joint to the lower control arms. 7) Remove the pivot bolts holding the lower control arm to the frame and remove control arm from truck. 8) Unbolt and remove original bump stops from factory arms and bolt them to you new DJM control arm. 9) Drill out the small hole on the end of the torsion bar receiver to 7/16″on both sides. This is to accept the 7/16″ x 5- 1/2″ bolt supplied. 10) Compare the new DJM control arms with the factory ones. Carefull note the diameter of the factory ball joint mounting holes. You will find either three 10mm hole used on most earlier models or larger 13mm holes on late models. If you factory arms have the 10mm holes continue to step # 10. If factory holes are 13mm it will be necessary to enlarge the holes with a 1/2″ drill bit(Fig. C). Fig. C 11) Mount the DJM control arms to the truck. Make sure the steering stops are facing the front of the truck. Insert the pivot bolts and install the washers and nuts. DO NOT TIGHTEN YET . 12) Bolt on the tensioncompression rods to the lower control arms. It mat be necessary to loosen the large nuts that hole the tensioncompression rods to the frame in order to rotate the rods to the proper angle to align bolts into control arms.

Related Content:

arm cam download

TOYOTA TACOMA RETRACTABLE HARD TRUCK BED COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

download
STEP 1: REMOVE CONTENTS FROM THE BOX Remove canister and top cover from the large box. Remove rails and Guide strips from the Rail box. Perform a quick inventory to insure all parts are there. (If any parts are missing call Pace Edwards Technical Support for replacement, INSTALLATION INSTRUCTIONS 3 STEP 2: PLACE CANISTER Use a soft rag or some packing materials from the box to wedge between the fabric roll and handle to temporarily keep the fabric roll from winding into the canister. Remove the screw and metal clip holding the handle to the canister. Place the canister in the front of the truck bed, cab side forward against the truck sill, in the position required for unrolling. Center side to side. Do not attach the canister yet. CAUTION! CAUTION! PERMANENT DAMAGE MAY BE CAUSED IF THE HANDLE ASSEMBLY IS ALLOWED TO RETRACT INTO THE CANISTER WITHOUT PROTECTION ON THE UNDERSIDE OF THE FABRIC PANEL! STEP 3: INSTALL & FASTEN THE RAILS HARDWARE USED: INNER RAIL CLAMP BRACKET x 4 1/4″ FLAT WASHER x 4 1/4″-20 NUT X 4 Slide the four (4) Inner Rail Clamps (2 on each side) through the Tie Down Bars of the truck. Open the rail box along the length of the box; lift rails out to avoid scratching the rail surface on the package staples. The side rails are marked “left” and “right” (left is the driver’s side of the truck). With the tailgate closed, place the side rails in position on the truck bed with the Rail Clamp Brackets resting on the Inner Rail Clamps. Loosely assemble the Rail Clamp Brackets to the Inner Rail Clamps with the 1/4″ Washer, 1/4″ Lock Washer and 1/4-20 Nut on each side of the truck bed. Correct spacing to the tailgate should be 1/16″ to prevent the tailgate from striking the side rails when closing. Apply downward pressure while tightening the Rail Clamp to the Inner Rail Clamp, especially on the tailgate end. This will ensure a tight seal, fi rm seat, and good fi t on the truck bed.

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette, 2002 silverado remove front driveshaft, 2003 mitsubishi eclipse replace evapulator, how to remove malibu 2008 instrument gauge cluster cover, Redezvous Dash Removal, how to remove the heater core on 2000 VW Beetle, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, 2004 Buick lesabre inrument cluster removeal

Toyota Tundra Quad Cab TONNEAU INSTALL ATION GUIDE Warranty Care And Maintenance

0

Filed Under (Toyota Manuals) by admin on 09-11-2011

download
UNDERCOVER INSTALLATION INSTRUCTIONS EASY AS 1-2-3 S T E P 1 R e a r M o u n t i n g B r a c k e t Model 4040 Toyota Tundra Quad Cab Short Bed 2004 – Current Page 3 FORM # IG4040 Modified July 2005 Place the rear bracket against the truck stake pocket or tail light well Page 4, Figure 1, Pictures A & B. Use two of the holes in rear bracket which are unobstructed by the truck bed, (there will be three to choose from), one hole as far forward as possible and one hole as far back as possible (this will vary depending upon truck model) Page 4, Figure 2. Place a 5/16Óx 1 1/4″bolt with a 5/16″lock washer and a 5/16″washer through the hole in bracket Page 4, Figure 3. Place clamp on backside of bracket behind the bed lip of the truck. Thread the bold into the clamp and tighten being careful to not let the clamp twist while tightening. Make sure bracket is held down tightly against truck bed rail before tightening. Repeat procedure for second clamp. Mounting bracket bolts must be tightened down without bending the bracket. Keep the clamps straight and do not let them turn while tightening Page 4, Figure 3, Picture C & D. WARNING! Bolts must be tightened to the correct torque to prevent any movement of the bracket on the truck bed. Bolts must be re-checked for tightness periodically. Failure to do so could cause serious damage to both the truck and/or your Undercover. Repeat Steps A through C for opposite side of the truck bed. D C B A Footnote: Normal installation does not require the use of a torque wrench. But it is a good idea to compare how tight you are currently tightening the bolts with the tool you are using with a torque wrench just so you can get “the feel”of how tight 15-ft./lbs. or 180-in./lbs. of torque actually is

How to bypass the VATS (PASSKey II) system in a late model GM vehicle

0

Filed Under (More Manuals) by admin on 16-09-2011

download
Pontiac 1994-1996 Grand Prix 1992-1999 Bonneville 1993-2002 Firebird/Trans Am/Firehawk Buick 1994-1996 Regal 1992-1999 LeSabre 1991-1996 Park Avenue 1991-1996 Roadmaster Oldsmobile 1994-1997 Cutlass Supreme 1992-1999 Eighty Eight/LSS/Ninety Eight/Regency 1991-1996 Custom Cruiser Wagon Chevrolet 1995-1999 Monte Carlo 1995-2001 Lumina 1993-2002 Camaro 1986(?)-1996 Corvette (C4) Cadillac How to bypass the VATS system in a late model GM vehicle Bullet-Style” solderless connectors Heat Shrink Tubing Resistors of varying values (totalling the resistance measured across the key’s “pellet”) Alright, let’s begin the madness: 1. Take your DMM, set it to measure Ohms (use the 20k setting.) Measure the resistance across the pellet of the ignition key. Place one probe on the silver part of one side of the pellet, and the other probe on the other side. Write this value down. 2. Purchase a resistor or resistors that add up to the value measured in step 1. Radio Shack is a great place to go for the resistors, heat shrink tubing, and the “bullet-style” solderless connectors. 3. Take the 16 ga. wire and cut into 2 four-inch pieces. 4. Strip off approx 1/16″ of insulation off each side of both wire pieces. 5. Put your resistors together in series (or if you’re lucky and have a chip that has a resistance that matches a single resistor) and solder one wire to one end of the resistor(s) and the other wire to the other side. Example: You measure 11.72 on the 20k (k meaning kilo or 1,000) scale. The closest match is 11.801 which is a #15 “chip.” Always remember that resistors have a tolerance of 2%, meaning the resistance value of the “pellet” can be either 2% higher or 2% lower than 11.801 k ohms (11.72 falls in tolerance range.) You will want to aim for 11,801 ohms. So when you go to Radio Shack you want to pick up a 10,000 ohm (10k,) a 1,000 ohm (1k,) and an 800 ohm resistors to wire together in series to achieve the 11.801k ohm value.

Related Content:

07 colorado passlock, vats key modgler location 1996 pontiac bonneville, vat for 1996 park avenue, pics of vat\s wire on 1994 corvette, p1349 bmw 530i 2003, how do I replace the VATS module on a 1997 buick lesabre, bypass vats on a 1997 buick lesabre, 99 lesabre vats bypass resistor, 1993 corvette vats bypass, 1993 corvett icm bypass

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, location of mode motor for 99 honda civic lx, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram, Hino 268 2013 fuse box for heater location