1996 pontiac grand am repair manual pdf

You search PDF repair manual about 1996 pontiac grand am repair manual pdf, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1996 pontiac grand am repair manual pdf Direct Download speed 5432 Kb/s

  1996 pontiac grand am repair manual pdf Full Version speed 8172 Kb/s



1997 Mitsubishi Diamante LS Sedan Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 10-04-2012

download
REMOVAL 1. Remove the crankshaft pulley with pulley holding pins and end yolk holder tool Nos. MD998715 and MB990767, or equivalents. 2. Refer to the illustration for the service procedures, noting the following: 3. Before removing the timing belt, align the timing marks and loosen the center bolt on the tension pulley to remove the timing belt. 4. If the auto tensioner rod is in its fully extended position, reset it as follows: a. Keep the auto tensioner level and, in that position, clamp it in the vise with soft jaws. NOTE: Make a mark on the back of the timing belt, indicating the direction of rotation, so it may be reassembled in the same direction if it is to be reused. Zoom Sized for Print Zoom Sized for Print b. Push in the rod little by little with the vise until the set hole A in the rod is aligned with that B in the cylinder. c. Insert a wire, 1.4 mm (0.055 inch) in diameter, into the set holes. d. Unclamp the auto tensioner from the vise. e. Install the auto tensioner. INSTALLATION 1. Align the timing marks of the camshaft sprockets and crankshaft sprocket. 2. Install the timing belt by the following procedure so that there is no defection in the timing belt between each sprocket and pulley. a. Crankshaft sprocket b. Idler pulley c. Camshaft sprocket (front side) d. Water pump pulley e. Camshaft sprocket (rear side) f. Tension pulley 3. Turn the camshaft sprocket (right side) counterclockwise until the tension side of the timing belt is firmly stretched, and then check again that all timing marks are aligned. 4. Use the tension pulley socket wrench tool No. MD998769, or equivalent, to push the tension pulley into the timing belt, and then temporarily tighten the center bolt. 5. Use the crankshaft sprocket spacer tool No. MD998769, or equivalent, to turn the crankshaft 1/4 of a turn counterclockwise and then turn it again clockwise until the timing marks are aligned.

2008 TOYOTA RAV4 DOOR SILL ENHANCEMENT REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 27-02-2012

download
1. Check Kit Content. (a) Check kit for content and damage. (Fig. 1-1) 2. Apply tape. (a) Using the factory door sill plate as a guide, apply tape to the door sill surface at each end of the sill plate as shown. (Fig. 2-1) 3. Remove Factory Door Sill Plates. (a) Using an NRT, Lift the edge of the factory sill plate. (Fig. 3-1) (b) Once the edge of the sill plate has been lifted the plate may be removed by hand by pulling firmly upward. Be sure not to damage the weather strip in the process. (c) Discard the factory door sill plate. Fig. 2-1 Fig. TOYOTA RAV4 2008 – DOOR SILL ENHANCEMENT Procedure Page 3 of 5 pages Issue: A 12/3/07 4. Installation Preparation. (a) Thoroughly clean all installation surfaces. (i) Use a clean lint free cloth. (ii) Clean surface thoroughly using VDC approved cleaner and wipe dry Do allow cleaner to air dry. (Fig. 4-1) (b) Ensure door sill enhancement to be between 70 F and 110 F at time of installation. (c) Ensure vehicle surfaces to be between 70 F and 110 F at time of installation. (d) Do not touch or allow debris or contaminates to come in contact with the adhesive backing before installation. (e) Inspect parts prior to installation. Dry fit parts for alignment reference. 5. Install Front Door Sill Enhancements. (a) Check Part Number label on back of door sill enhancement for applicable side of vehicle, Right Hand or Left Hand and Front or Rear. (b) Position part over vehicle door sill area to check for proper fit and orientation prior to installation. NOTE: The vehicle name logo on the door sill enhancement must be oriented as to be read from the outside of the vehicle. (c) Remove the tape liner from the door sill enhancement. Do not touch the adhesive

Related Content:

2014 rv4 sills, vdc cleaner

1995 Ford Truck F 150 2WD Pickup New Cylinder Head Bolt Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-02-2012

download
ORQUE SPECIFICATIONS FOR THE NON-FLANGED STANDARD HEX HEAD BOLTS, TIGHTEN IN TWO (2) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 75-88 N-m (55-65 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 88-98 N-m (65-72 lb.ft.). FOR ALL TORQUE TO YIELD HEX HEAD BOLTS, TIGHTEN IN THREE (3) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 34-47 N-m (25-35 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 61-75 N-m 45-55 lb.ft.). 3. Tighten all bolts in sequence (Figure 2) an additional 1/4 turn (85-95 degrees). NOTE: WHEN THE CYLINDER HEAD BOLTS HAVE BEEN TIGHTENED FOLLOWING THESE PROCEDURES, IT IS NOT NECESSARY TO RETIGHTEN THE BOLTS AFTER EXTENDED OPERATION. CAUTION: TORQUE-TO-YIELD CYLINDER HEAD BOLTS MUST BE REPLACED WITH NEW BOLTS. DO NOT REUSE TORQUE-TO-YIELD BOLTS. TORQUE-TO-YIELD BOLTS MAY ONLY BE USED ONE (1) TIME. PART NUMBER PART NAME F3ZZ-6065-E Cylinder Head Bolt

Related Content:

1999 2 5 ford ranger head bolt torque, D-17 manfold bolt torqe, ranger 1999 3 0 head torque diagram, torque angle specs 3100 1998 buick, torque sequence 300m 3 5 heads

1997 Dodge Grand Caravan POWERTRAIN CONTROL MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 06-02-2012

download
POWERTRAIN CONTROL MODULE (PCM) Removal & Installation 1. The PCM is located between driver’s side front fender and power distribution center, near battery. See Fig. 1 . Disconnect negative battery cable and then positive battery cable from battery. 2. Remove bolts on side of power distribution center that secure power distribution center to mounting bracket. Remove heat shield from outside of battery. Remove battery. 3. Rotate power distribution center toward the engine to disengage power distribution center from rear mounting bracket. Pull power distribution center toward rear of vehicle to disengage power distribution center from front mounting bracket. 4. Allow power distribution center to lay aside for access to PCM. Remove electrical connectors from PCM. Electrical connectors may be removed by squeezing tabs on electrical connector together and pulling electrical connector from PCM. Remove bolts and PCM. To install, reverse removal procedure. Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. Default data is used until new data from each key start is stored. As the computer restores its memory from each new key start, driveability is restored. Driveability problems may occur during the relearn stage. Depending on the vehicle and how it is equipped, the following driveability problems may exist: z Rough or unstable idle. z Hesitation or stumble. z Rich or lean running. z Poor fuel mileage. z Harsh or poor transmission shift quality. To accelerate relearn process after battery removal and installation, vehicle should be road tested in the following manner: z Vehicle at normal operating temperature (cooling fan cycles). z Accelerate at normal throttle position (20-50%). z Cruise at light to medium throttle. z Decelerate to a stop, downshifting and using brakes normally. Manufacturers identify specific relearn procedures. See RELEARN PROCEDURES. Always complete the procedure before returning the vehicle to the owner. RELEARN PROCEDURES Theft Alarm Relearn Procedure 1. Theft alarm relearn is necessary whenever battery is disconnected or dead battery is boosted. If battery is connected or boosted without conducting relearn procedure, alarm system will enter power-up mode and vehicle will not start. 2. Before reconnecting battery or connecting booster, insert door key into driver side door lock

Related Content:

IDLE RELEARN 02 CAMRY, 04 rav4 idle at 6000 rpm after battry change, 2001 malibu throttle position sensor relearn procedure, 2006 cheverolet impala will not idle, 2008 dodge grand caravan coolant fan runs continuasly, dodge caravan1997 transm autom 3 3l how connected with radiator, Dodge Cruise Control Repair 2012 caravan, IRRATIC IDLING 87 2 8 V6 BLAZER

2002 BMW 325I 2.5L Air Pump Repair manual

0

Filed Under (Bmw Manuals) by admin on 05-02-2012

download
Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible. 4. Check valve on front right of cylinder head can be supplied with vacuum and visually checked for opening of valve. 5. Vacuum line from check valve to operating solenoid should also be inspected for cracks or being disconnected. Vacuum line follows right side of cylinder head to back of cylinder head to the secondary air solenoid located under left rear side of intake manifold. 6. The solenoid should allow vacuum flow to the check valve during vacuum pump operation. The solenoid is controlled directly by the engine control module and receives power during key-on-engine-off. Potential Causes: A.I.R. Check Valve Engine Control Module (ECM) Codes — Engine control module fault. Defective Secondary Air Pump Secondary Air Pump Relay Secondary Air Supply Hose Broken Vacuum Line

Related Content:

where is the secondary air pump located a 2002 rendezvouz, 2008 trailblazer air pump install, how to test a secondary air check valve on a 2002 bmw 325i, where is the air pump on a 2002 rendezvouz, where should a check valve be located

2002 Daewoo Leganza SE Dashboard / Instrument Panel Service and Repair Manual

0

Filed Under (Daewoo Manuals) by admin on 02-02-2012

download
Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the floor console. 3. Remove the sun sensor and the automatic temperature controls assembly. 4. Remove the tweeter speakers and the stereo cassette AM/FM radio. Refer to Section 9F, Audio Systems. 5. Remove the screws and the instrument panel storage compartment. 6. Remove the instrument cluster dimmer switch assembly. 7. Remove the instrument cluster. 8. Remove the chime module. 9. Remove the kick panels. 10. Remove the glove box. 11. Remove the screws and the glove box housing. 12. Disconnect the glove box housing electrical connectors. 13. Remove the knee bolster. 14. Remove the nuts and the bolts securing the steering column. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 2 15. Disconnect the steering column electrical connectors. 16. Lower the steering column. 17. Remove the screw behind the stereo cassette AM/FM radio. 18. Remove the screw securing the instrument panel to the heater air distributor case. 19. Remove the bolts and the glove box brace. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 3 20. Remove the instrument panel screw behind the glove box brace. 21. Remove the instrument panel bolts below the windshield. 22. Remove the bolts securing the bottom of the instrument panel to the floor. 23. Remove the bolts securing the sides of the instrument panel to the body. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 4 24. Disconnect the instrument panel electrical connectors. 25. Remove the instrument panel. Installation Procedure 1. Position the instrument panel in the vehicle. 2. Connect the instrument panel electrical connectors. NOTE: Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion. 3. Install the bolts securing the sides of the instrument panel to the body. Tighten Tighten the instrument panel-to-body bolts to 22 N.m (16 lb-ft) . 4. Install the bolts securing the bottom of the instrument panel to the floor. Tighten Tighten the instrument panel-to-floor bolts to 22 N.m (16 lb-ft) .

Related Content:

toyota matrix 2003 evaporator removal, take dashbord daewoo leganza, how to remove headliner from cadillac escalade ext 03, daewoo 1760xl service manual, diy brass instrument repair tools, 2002 saturn sl2 owners manual, nissan sentra 02 2 5 cam torque, p1627 daewoo, 2002 daewoo lanos code, 2 2 dtec deewoo engine timing marks

1988 Cadillac DeVille Steering Column Service and Repair Manual

0

Filed Under (Cadillac Manuals) by admin on 30-01-2012

download
Disassembly 1. Remove dash panel bracket and store bracket in a safe place to prevent damage to mounting capsules. 2. Place column in a vise using both weld nuts of either set A or B, Fig. 29. The vise jaws must clamp onto the sides of weld nuts indicated by arrows shown on set B. Do not place column in vise by clamping onto only one weld nut, by clamping on one weld nut of both sets A and B or by clamping onto the sides not indicated by arrows, as damage to column could result. 3. Inspect steering shaft to determine type of thread used for steering shaft nut. Metric type shafts can be identified by a groove located in area of steering wheel locating splines, while shafts with American type threads do not have this groove. If shaft has metric type threads, the forcing screw of Lock Plate Compressor Tool J-23653 must be removed and replaced with the metric forcing screw J-23653-4 before installing lock plate compressor tool on steering shaft. Compress lock plate using lock plate compressor tool, then pry snap ring from shaft groove and discard wing. Remove lock plate compressor tool and lock plate. 4. Remove directional signal switch, lock cylinder and ignition key warning switch, then remove steering shaft from lower end of column. 5. On power steering columns, remove steering shaft lower bearing from plastic adapter at lower end of column. 6. Remove four turn signal housing to column jacket retaining screws and remove housing and shroud assembly. 7. Remove three shroud to signal housing retaining screws and remove shroud. 8. Using hand as shield to prevent lock inhibitor lever spring wire from flying out, remove lock inhibitor lever and spring wire. 9. Lift ignition switch actuating rod, rack assembly, shaft lock bolt and spring assembly from housing, then if necessary, remove rack preload spring. 10. Remove ignition switch actuator sector through lock cylinder hole by pushing firmly on block tooth of sector with a blunt punch or screwdriver.

Related Content:

ignition switch rack spring, cadillac 2004 deville front panel below steering wheel, cadillac 2004 deville front steering wheel panel

2004-2007 Ford Explorer MIL ON WITH DTC P0463 OR ERRATIC FUEL GAUGE OPERATION SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 24-01-2012

download
ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. For vehicles with customer symptom of erratic fuel gauge operation (with no MIL on), proceed to Step 1a. For vehicles with a customer symptom including the MIL on, proceed to Step 1b. If unable to verify the concern, do not continue with this TSB. a. Follow the appropriate pinpoint test (PPT) for “Fuel Gauge Inaccurate” in Workshop Manual (WSM), Section 413-01. If PPT test results lead to fuel pump module replacement, proceed to Step 2. If PPT test results isolate any problem other than fuel pump module replacement, repair as indicated and do not continue with this TSB. b. Install diagnostic scan tool to retrieve DTCs. If DTC P0463 is retrieved, proceed to Step 2. If DTC P0463 is not retrieved, this TSB does not apply, follow normal WSM diagnostics. 2. Remove fuel tank per WSM, Section 310-01 3. Remove fuel pump assembly from fuel tank per WSM, Section 310-01. See Figure 1 (Chart) to determine if a kit (contains a fuel level sensor assembly, a wire harness and heat shrink tube) or fuel pump assembly is required for repair. For vehicles that can be serviced with a kit go to Step 4. For vehicles that require fuel pump assembly replacement, go to Step 12. 4. Remove the fuel level sensor assembly (sender card/float rod assembly) from the fuel pump assembly per WSM, Section 310-01

Related Content:

2007 ford explorer fuel fill problem

2006 Dodge Truck RAM 2500 DENSO A/C COMPRESSOR Service and Repair Manual

0

Filed Under (Dodge Manuals) by admin on 23-01-2012

download
DENSO A/C COMPRESSOR REMOVAL NOTE: * The compressor clutch assembly can be serviced with the refrigerant system fully-charged. * Typical A/C compressor shown in illustrations. 1. Disconnect and isolate the negative battery cable. 2. Remove the accessory drive belt. 3. Disconnect the engine wire harness from the compressor clutch field coil connector (1) located on the top of the A/C compressor (5) . Remove the bolts that secure the A/C compressor to the engine and support the A/C compressor. 5. Carefully remove the compressor clutch field coil connector and wire lead from the connector bracket (2). 6. Remove the compressor shaft bolt (3). A band-type oil filter wrench or a strap wrench may be used to hold the clutch plate (4) from rotating during bolt removal. CAUTION: Do not pry between the clutch plate and the pulley and bearing assembly to remove the clutch plate from the compressor shaft as this may damage the clutch plate. NOTE: Use care not to lose any clutch shim(s) during removal of the clutch plate, as they may be reused during the clutch plate installation process. 7. Tap the clutch plate (2) lightly with a plastic mallet to release it from the splines on the compressor shaft (1) and remove the clutch plate and shim(s) (3). 8. Using snap ring pliers (2), remove the snap ring (1) that secures the pulley and bearing assembly (3) to the front of the A/C compressor and remove the pulley and bearing assembly. 9. Using snap ring pliers (Special Tool C-4574 or equivalent) (1), remove the snap ring (4) that secures the compressor clutch field coil (2) to the front of the A/C compressor (3) and remove the field coil. INSTALLATION NOTE: Typical A/C compressor shown in illustrations. 1. Align the dowel pin on the back of the compressor clutch field coil (2) with the hole in the front of the A/C compressor (3) and position the field coil onto the compressor. Be certain that the compressor clutch field coil wire lead is properly routed so that it is not pinched between the A/C compressor and the field coil. CAUTION: The snap ring must be fully and properly seated in the groove or it will vibrate out, resulting in a clutch failure and severe damage to the A/C compressor. NOTE: A new snap ring must be used to secure the compressor clutch field coil to the A/C compressor. The bevel side of the snap ring must face outward and both snap ring eyelets must be oriented to the right or to the left of the field coil dowel pin location on the A/C compressor. 2. Using snap ring pliers (Special Tool C-4574 or equivalent) (1), install the snap ring (4) that secures the compressor clutch field coil to the front of the A/C compressor. Be certain that the snap ring is fully and properly seated in the groove and oriented correctly. CAUTION: * Be certain to position the compressor clutch field coil wire lead so that

Related Content:

1994 mazda b3000 how to replace clutch and slave free download, 2004 f250 ac compressor replacement, changing Saab 93 clutch 2003, hummer h1 ac compressor wiring, air compressor for 2003 pontiac bonneville ssei, 87devillebrakelightswitchcausingona/c, scion xb compressor control solenoid problems, 2004 chevy cavalier torque specs clutch, starter clutch cvt trans mission honda rebuilt, how to replace a clutch on 2003 chevrolet cavalier

2002 Ford Crown Victoria/ Grand Marquis Fuel Injection Supply Manifold Workshop Manual

0

Filed Under (Ford Manuals) by admin on 21-01-2012

download
Removal All vehicles WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in personal injury. WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved. Failure to follow these instructions may result in personal injury. 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 2. Relieve the fuel pressure. For additional information, refer to Section 310-00A (Gasoline) or Section 310-00B (Natural Gas). 3. Disconnect the fuel lines. For additional information, refer to Section 310-00A (Gasoline) or Section 310-00B (Natural Gas). 4. Remove the throttle body (9E926). For additional information, refer to Throttle Body in this section. 5. On gasoline engines, remove the EGR valve to exhaust manifold tube (9D477). For additional information, refer to Section 303-08 . 6. Remove the drive belt (8620). For additional information, refer to Section 303-05 . Vehicles equipped with natural gas engines 7. Disconnect the fuel temperature sensor connector. 8. Disconnect the fuel pressure sensor connector. All vehicles 9. Disconnect the main fuel shut-off solenoid connector. 10. Disconnect the generator cable, electrical connector, and harness pin-type retainer. 11. Remove the bolts and the generator mounting bracket (10153). 12. Remove the bolts. 13. Unclip the accelerator cable (9A758) and the speed control actuator cable (9A825) from the two crash brackets and position out of the way. 14. Separate the LH heated oxygen sensor and the transmission electrical connector from the bracket at the rear of the cylinder head. 15. Separate the fuel charging wiring pin-type retainer from the crash bracket. 16. Remove the wiring bracket. * Disconnect the wiring connectors. * Separate the transmission harness from the stud. * Remove the nut and the bolt and remove the bracket 17. NOTE: On natural gas vehicles, there are no EGR vacuum connections. Disconnect the vacuum lines and position out of the way. 18. Remove bolt and stud and remove the crash bracket. 19. Disconnect the ground connector from the RH rear stud. 20. Disconnect generator harness locator retainer from LH front stud. 21. Disconnect the eight fuel injector electrical connectors