Skip to content

1996 town and country owners manual

You search PDF repair manual about 1996 town and country owners manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly

1996 – 2000 Civic 2-door Front Windows Bind or Have Come Out of the Run Channel Repair Manual

download
REPAIR PROCEDURE 1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual. 2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator. 3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot. 4. Check the year and VIN. If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5. If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8. 5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts. 6. Disconnect the power window motor connector, and detach the harness clip (if applicable); then lift and remove the regulator through the opening in the door. 7. Install the new regulator in the door, then loosely install the two rear mounting bolts and the two roller guide bolts. Do not tighten the two front mounting bolts yet. Go to step 9. 8. Loosen the window regulator’s two rear mounting bolts, two front mounting bolts, and two roller guide bolts

1989-1996 Dodge Dakota Trucks COIL Ignition Tests Manual

download
Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: • 1989-92 engines: mounted to the firewall • 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor • 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head • 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket. Fig. 2: Ignition coil mounting-all 1989-92 models Fig. 3: Ignition coil wiring and mounting hardware-1993- 96 2.5L engine 1. Inspect the ignition coil for arcing while the engine is running. If the engine will not start, this can be performed while the engine is cranked by either an assistant or a remote starter. Look at the coil in dim or low light to aid visibility of any arcing. Fig. 4: Ignition coil mounting-1993-96 3.9L and 5.2L/5.9L LDC engines 2. Arcing at the tower will carbonize the wire boot, which, if it is connected to a new ignition coil, will cause the coil to fail. In such cases, clean all the carbonization away or replace the components as necessary. Fig. 5: Ignition coil mounting-1993-96 5.9L HDC engine 3. Using a coil tester or ohmmeter according to the manufacturer’s instructions, test the primary and secondary resistance. Replace any coil that does not meet the specifications indicated in the accompanying chart. 4. Inspect the secondary coil wire for any sign of damage. Replace if any damage is found. Carbon tracking on the old wire can cause arcing and the failure of a new ignition coil. REMOVAL & INSTALLATION 1989-92 Models See Figures 6 and 7 1. Disconnect the negative battery cable. 2. Disconnect the three wires from the coil. Mark them to identify for installation. Fig. 6: Remove the coil bracket bolt at the cowl Fig. 7: Unscrew the coil mounting hardware, then remove the coil from the vehicle 3. Unplug the condenser suppressor connector from the coil, if equipped. 4. Unbolt and remove the coil. To install: 5. Bolt down the coil with old bolts. 6. Connect wires to coil making sure that the proper wires are connected where they should be. 7. Connect the condenser suppressor, if equipped. 8. Connect the battery negative cable Removal and Installation V6 AND V8 ENGINES 1. Disconnect the negative battery cable. 2. Disconnect the primary wiring from the ignition coil. 3. Disconnect the secondary spark plug wire from the coil. 4. Remove the two bolts and withdraw the coil from its mounting bracket. To install:
5. Position the coil on its bracket and install the two bolts. Tighten them to 100 inch lbs. (11 Nm). If the bracket has been tapped for coil mounting bolts, these fasteners require less torque, so tighten them to 50 inch lbs. (5 Nm). 6. Connect all wiring to the ignition coil. TESTING See Figure 1 The only test you can perform without a DRBII scan tool, or equivalent, is a basic check of the sensor only.

1996-2000 Honda Civic Door Panel REMOVAL And INSTALLATION Manual

download
Honda Door Panel 96-00 Civic REMOVAL & INSTALLATION Remove the screw from behind the interior door handle Slide out the door handle trim as shown Removing the door panel from the passenger side door View of the inside of the door, panel removed 1. Remove the screw from the door handle trim. 2. Slide the handle assembly forward and out to access the lock rod clip. 3. Release the clip 4. Disconnect the door lock switch 5. Remove the door opener handle assembly. 6. Carefully pry at the small opening on the bottom of the speaker grill. 7. Remove the speaker grille. 8. Remove the speaker mounting screws. 9. Detach the electrical connector and remove the speaker. 10. Remove the screws in the armrest. 11. Remove the center from the trim clip at the upper front of the door panel and remove the clip. 12. Using a suitable trim panel removal tool, unsnap the door panel from the door frame. 13. Carefully lift the door panel up and away from the door frame. To install: 14. Installation is the reverse of the removal procedure. Honda Civic/Del Sol 1996-2000 Electric Window Motor REMOVAL & INSTALLATION 1. Remove the regulator from the door assembly. 2. Except for the rear doors, drill a hole through the regulator sector gear and backplate. Install the bolt and nut to lock the sector gear in position. Be careful not to drill a hole closer than 7/ 16 in. (11mm) from the edge of the sector. Also, do not drill through the lift arm attaching portion of the sector gear, or the joint integrity will be jeopardized. 3. Drill out the ends of the motor attaching rivets using a 1/ 4 in. (6mm) bit. 4. Remove the motor and the remaining portions of the rivets from the regulator. Except for the rear doors, one rivet will not be accessible until assembly. Regulator and motor assembly—except rear doors Secure the rivets by collapsing the rivet ends using a ball peen hammer To install: 5. Position the new motor to the regulator. With the aid of an assistant, install new rivets by collapsing or crushing the rivet ends using a ball peen hammer. 6. Except for the rear doors, once two of the three rivets have been installed, remove the bolt securing the sector gear to the backplate, then use an appropriate electrical source (such as the vehicle’s window motor harness) to rotate the regulator, providing access to the remaining rivet. 7. Except for the rear doors, use a flat nosed rotary file to grind off one sector gear tooth from the side which does not contact the driven gear. This is necessary to reach the remaining rivet. Remove the old rivet, then install the remaining new rivet. 8. Install the regulator to the door assembly.

1994 Ford Town Car/ Crown Victoria/ Grand Marquis Trim Panels, Door Removal And Installation Manual

download
Trim Panels, Door Front Town Car The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification. Removal CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove. 1. Snap out two door pull strap retaining screw covers. Remove screws. 2. Remove two screws on front and rear side of front door trim panel. 3. Using the Trim Pad Removing Tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent, pry the trim panel retaining clips from the door inner panel. NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins. 4. Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors. 5. Disconnect driver seat regulator control processor switch (driver door only) if equipped. 6. Twist out interior lamp wire assembly and remove the front door trim panel. Installation 1. Ensure plastic watershield is secured to door panel. 2. Position front door trim panel to door. Connect interior lamp wiring. 3. Position the window regulator control switch housing and connect switch connectors. 4. Connect driver seat regulator control processor (14C708) (driver door only) if equipped. 5. Align door lock side to its mating slide on the sheet metal (front doors only) 6. Snap in front door trim panel . Ensure all retainers fit properly. 7. Install two retaining screws on front and rear side of front door trim panel . 8. Install two retaining screws and pull strap covers. Removal 1. Remove outside rear view mirror remote control unit. 2. Remove window regulator control switch housing by gently prying up, starting at the front. 3. Disconnect all connectors from window regulator control switch housing. 4. Remove inside door handle cup (22634) by gently prying at screwdriver slot with a screwdriver. 5. Remove push pin from front door trim panel upper front extension and remove screw. 6. Remove lower self-tapping screw retaining front door trim panel to door inner panel. 7. On Grand Marquis only, pry up screw covers from door pull handle and remove screws and handle. 8. Lift front door trim panel upward and snap out trim panel. 9. Disconnect wire harnesses from door panel as required and remove front door trim panel . Installation 1. Connect wire harnesses to front door trim panel as required. 2. Install front door trim panel by pushing in and down until it snaps into place. 3. Install all self-tapping screws retaining front door trim panel to door inner panel. 4. On Grand Marquis only, install door pull handle, tighten screws and install screw covers. 5. Install push pin covering screw on trim panel upper front extension. 6. Install inside door handle cup . 7. Install window regulator control switch housing.