1996 toyota avalon transmission schematics

You search PDF repair manual about 1996 toyota avalon transmission schematics, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1996 toyota avalon transmission schematics Direct Download speed 5432 Kb/s

  1996 toyota avalon transmission schematics Full Version speed 8172 Kb/s



4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

how to replace solenoid e on a245e transmission problems, yhs-lavasoft, gm 4l60e band adjustment screws, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, 2005 explorer transmission exploded view, how to check tranmission fluid on 2012 kia sedona, 2003 trailblazer torque converter removal, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio

Toyota ISO Adapter Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 19-05-2011

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

Related Content:

2002 toytoa camry tank vent valve, toyota 4af engine repair manual, p67-y toyota vitz, 2002 toyota tundra 4 wheel drive suspencion, 1998 toyota A245E automatic transmission rebuild manual, 2009sienna v6 thermostadt extraction, 2004 toyota highlander window diagram, p1225 spill control circuit, show prado 1999 valve attached to rear brake pipe with spring, diagram of front passenger seat occupant sensors and where 2005 toyota camry located

2000 Chevy Truck S10/T10 Blazer Transfer Case Removal And Installation Manual

0

Filed Under (Chevy Manuals) by admin on 18-05-2011

download
Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case. 12. For vehicles equipped with a manual transmission, remove the six nuts securing the transfer case and bracket to the transmission 13. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 14. For vehicles equipped with a automatic transmission, remove the six nuts securing the transfer case and bracket to the transmission adapter. 15. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 16. Remove and discard the gasket. Installation Procedure 1. Install a new gasket to the transmission. Use sealer GM P/N 12346004 in order to hold the gasket in place. 2. Raise and position the transfer case to the vehicle Notice: Refer to Fastener Notice in Service Precautions. 3. For vehicles equipped with a automatic transmission, install the six nuts securing the transfer case and bracket to the transmission adapter. * Tighten the nuts to 47 Nm (35 lb ft) . 4. For vehicles equipped with a manual transmission, install the six nuts securing the transfer case and bracket to the transmission. * Tighten the nuts to 47 Nm (35 lb ft)

Related Content:

wiring for case w20 loader, How to rebuild Kia Sorento Transfer Case, case 444-75 repair manuals free, np 208 service manual, Case 1845C Manual Download, Chevy NP208 Rebuild Instructions, toyota tacoma ground wire transfer case, 2001 ford sports trac 4x4 transfer case wiring diagram, rockwell t-226 manual, f150 transfer case problems

1990 Toyota Supra Factory Repair Manual

0

Filed Under (Toyota Manuals) by admin on 04-04-2012

download
REMOVAL AND INSTALLATION OF TRANSMISSION Removal of Transmission REMOVE NEGATIVE BATTERY CABLE CAUTION: Work must be started after approx. 20 se- conds or longer from the “LOCK” position and the nega- tive (-) terminal cable is disconnected from the battery. REMOVE CENTER CLUSTER FINISH PANEL REMOVE SHIFT LEVER FROM INSIDE OF VEHICLE RAISE VEHICLE AND DRAIN TRANSMISSION OIL NOTICE: Be sure the vehicle is securely supported. REMOVE PROPELLER SHAFT Remove the propeller shaft and insert SST into the extension housing. SST 09325-2001 0 (for W58 M/T) 09325-4001 0 (for R 1 54 MIT) DISCONNECT EXHAUST FRONT PlPE FROM TAIL PlPE (a) Remove the rubber hanger. (b) Disconnect the pipe at the front side of the converter. (R154 M/T) REMOVE EXHAUST FRONT PlPE (a) Disconnect the exhaust pipe bracket from the clutch housing. (b) Remove the nuts and exhaust pipe from the exhaust manifold. DISCONNECT SPEEDOMETER CABLE DISCONNECT BACK-UP LIGHT SWITCH CONNECTOR AND REAR SPEED SENSOR CONNECTOR (wl A.B.S.) MANUAL TRANSMISSION – Removal and Installation of Transmission MT-5 10. REMOVE CLUTCH RELEASE CYLINDER 11. REMOVE STARTER Remove the mounting bolts and lay the starter alongside the engine. 12. JACK UP TRANSMISSION SLIGHTLY Raise the transmission enough to remove the weight from the rear support. 13. REMOVE ENGINE REAR MOUNTING 14. REMOVE TRANSMISSION MOUNTING BOLTS AND FLYWHEEL HOUSING UNDER COVER 15.-1 (W58 M/T) REMOVE TRANSMISSION ASSEMBLY Pull out the transmission down and toward the rear. 15.-2 (R154 M/T) REMOVE TRANSMISSION ASSEMBLY WITH CLUTCH COVER AND DISC (a) Remove the two clutch housing covers. (b) Pull out the release fork through the left clutch housing hole. (c) Place the matchmarks on the clutch cover and flywheel. (d) Remove the clutch cover set bolts while turning the crankshaft pulley. HINT: Loosen each set bolt one turn at a time until spring tension is released. (e) Remove the clutch cover and disc from the flywheel, and fully move them toward the transmission. (f) Pull out the transmission with the clutch cover and disc.

2002 Isuzu Truck Axiom Vehicle Level Transmission and Drivetrain Automatic Transmission/ Transaxle Fluid – A/ T Service and Repair

0

Filed Under (Isuzu Manuals) by admin on 09-01-2012

download
Changing Transmission Fluid There is no need to change the transmission fluid unless the transmission is used under one or more of the following heavy duty conditions. A. Repeated short trips B. Driving on rough roads C. Driving on dusty roads D. Towing a trailer If the vehicle is used under these conditions, change the fluid every 20,000 miles (32,000 km). 1. Place a large drain pan under the oil pan. 2. Remove the transmission oil drain screw (2) and drain fluid. 3. Tighten drain screw (2). Torque: 38 Nm (28 ft. lbs.) 4. Remove the transmission overfill screw (1) and fill transmission through overfill screw opening, using DEXRON-III ATF. Note: Add transmission fluid until it flows out over the overfill screw opening. 5. Let engine idle until a fluid temperature between 32°C (90°F) and 57°C (135°F) is reached. 6. Add transmission fluid until it flows out over the overfill screw opening, then close the overfill screw (1). Torque: 38 Nm (28 ft. lbs.) Note: To prevent fluid leaks, the overfill screw and oil drain screws gasket must be replaced each time these screws are removed. Note: Check transmission fluid temperature with scan tool

Related Content:

1999 ISUZU RODEO HOW TO REPLACE TORQUE CONVERTER

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, canter 4d 35 interval wiper control relay, p0753 kia rio 2004, wiring diagram for mitsubishi canter ignition, Powertrain Generator 6500 Parts Diagram, bully side ste for jeep instructions, Kia Rio 2001 DTC P0753, 2006 pontiac g6 gt code po753, what is the tcc solenoid on a 2 2 cavalier, p1860 tcc pwm solenoid circuit electrical

1999 Mercury Sable V6-3.0L DOHC A/ T-Cooler Flushing Service Manual

0

Filed Under (Mercury Manuals) by admin on 25-06-2012

download
SERVICE PROCEDURE Prior methods of cooler flushing have not obtained the level of cooler cleaning and contaminant removal that is required to prevent repeat repairs. The “Turbo-Tank Heated Cooler Line Flusher” uses heated Automatic Transmission Fluid ( ATF ) and a pulsating action to loosen system contamination. Previous equipment used solvents to clean & flush coolers, lines and torque- converters. There are 2 issues with this method: Aerosol Solvents should never be used for several reasons. NOTE YOU MUST IDENTIFY THE RETURN COOLER LINE TO START THE BACK FLUSHING PROCEDURE. A quick way to identify the return cooler line (fluid coming out of the cooler and returning to the transmission) is to locate the return cooler line fitting on the transmission case . Refer to the following lists: Rear Wheel Drive ^Residual solvent contamination can cause damage to friction bonding materials within the transmission (Clutches and Bands). ^Lack of fluid heating and agitation prevents this method from completely removing contamination from lines, in-radiator coolers and auxiliary coolers. ^They do not provide the volume necessary to remove heavy contaminants. ^They evaporate quickly and essentially leave contaminants in pockets, bends, or wherever they are as the solvent dries. ^TORQSHIFT, 4R100, E40D, C6 – The REAR transmission case filling receives the return line. ^4R70W, AODE, AOD – The TOP transmission case filling receives the return line. ^A4LD, 4R44/55E, 5R55E, 5R55N, 5R55W, 5R55S The TOP transmission case filling receives the return line. ^CD4E – The REAR or Pump End transaxle case fitting receives the return line. ^4F27E – The REAR or Cover End transaxle case fitting receives the return line. ^AXOD, AXODE, AX4S, AX4N, 4F50N – The BOTTOM transaxle cooler line fitting receives the return line. 1. Check and top off fluid level of the “Turbo-Tank Heated Cooler Line Flusher” tank with transmission fluid. 2. Allow the fluid in the flusher 15-30 minutes to heat up to 140°F (60°C) before using. 3. Install line adapters into the transmission cooler lines. 4. Attach the flusher’s blue line to the transmission return cooler line quick disconnect. 5. Attach the flusher’s red line to the transmission outlet cooler line quick disconnect. a. Follow equipment instructions, to purge cooler lines and cooler prior to starting flushing procedure (using factory installed purge valve and clear hose on “Turbo-Tank Heated Cooler Line Flusher”). 6. Allow the cooling system to back-flush for 10-15 minutes, then flush the cooler in a forward/normal flow direction for an additional 10-15 minutes

Related Content:

4f27e overhaul manual/pdf, ax4n transmission repair manual pdf, 4f27e case torque specs, 4r100 low reverse sprag rotation, 5r55eiol pump spec, 5r55s overfill symptoms, 5r55w transmission manual download, cd4e transmission pump removal, Idetnify Ax4N automatic transmission

2005 TOYOTA AVALON TVIP V4 (REMOTE ENGINE STARTER) INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 2 of 33 pages Issue: C 02/02/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Visassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool removing the cable. (b) Remove the glove box under-dash cover. (Fig. 1-2) (c) Remove the passenger’s step cover. (Fig. 1-3) Fig. 1-1 10mm Wrench Negative Battery Cable Battery Step Cover Fig. 1-3 Nylon Panel Removal Tool Fig. 1-2 Under-Dash Cover Nylon Panel Removal Tool TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 3 of 33 pages Issue: C 02/02/05 (d) Remove the passenger’s cowl cover. (Fig. 1-4) (1) Remove one nut securing the cowl cover. (e) Remove one screw and one bolt from the glove box assembly. (Fig. 1-5) (f) Remove the glove box assembly. (Fig. 1-6) (1) Open the glove box door and remove three screws securing the glove box assembly. (2) Disconnect the trunk opener cancel switch from the glove box assembly if equipped. For vehicles with Smart Entry, the disassembly process ends on Step f. Go to Section 5. For vehicles without Smart Entry, continue the disassembly process. FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Step g) NOTE: Do not perform this step if the vehicle has Smart Entry. (g) Remove the driver’s step cover. (Fig. 1-7) Screw Fig. 1-5 10mm Wrench, Phillips Screwdriver Bolt Glove Box Assembly Cowl Cover Fig. 1-4 Nut Fig. 1-6 Nylon Panel Removal Tool, Phillips Screwdriver Screws (x3) Glove Box Assembly Trunk Opener Cancel Switch Connector Fig. 1-7 Step Cover Nylon Panel Removal Tool
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 4 of 33 pages Issue: C 02/02/05 FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Steps h-l) NOTE: Do not perform this step if the vehicle has Smart Entry. (h) Remove the driver’s cowl cover. (Fig. 1-8) (1) Remove the one nut securing the cowl cover. (i) Remove the hood release cable. (Fig. 1-9) (1) Do not bend the hood release cable. (j) Open the screw cover on the lower dash cover. Insert the tip of a Nylon Panel Removal Tool in the upper slot to loosen it. (Fig. 1-9) (1) Remove one screw and one bolt securing the lower dash cover. (k) Remove the lower dash cover. (Fig. 1-10) (1) Disconnect the temperature sensor (connector and aspirator hose) from the lower dash cover if equipped. (l) Carefully remove the driver side airbag assembly. (Fig. 1-11) (1) Remove four bolts securing the driver side airbag assembly. (2) Be careful not to get cut by the sharp metal edges. (3) Do not disconnect the airbag assembly. (4) Use the empty V4 kit box to support the airbag assembly on the floor

Related Content:

Prius upper glovebox door hinge, Prius repair glovebox door, toyota venza glove compartment box, how to take the back off a blu dask 3 5, colbalt where is the strarter located, 2005 toyota tacoma airbag fuse location, 2005 toyota corolla under carriage, clicking noise by glove box 2008 chevy impala, loud clicking noise in glove box impala, PICTURE OF GLOVE BOX LOWER BRACE ON CHEVY UPLANDER

2002 Dodge Truck RAM 2500 Symptom Related Diagnostic Procedures/ Installation Manual

0

Filed Under (Dodge Manuals) by admin on 16-02-2012

download
46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING Before road testing, be sure the fluid level and control cable adjustments have been checked and adjusted if necessary. Verify that diagnostic trouble codes have been resolved.Observe engine performance during the road test. A poorly tuned engine will not allow accurate analysis of transmission operation. Operate the transmission in all gear ranges. Check for shift variations and engine flare, which indicates slippage. Note if shifts are harsh, spongy, delayed, early, or if part throttle downshifts are sensitive. Slippage indicated by engine flare, usually means clutch , band or overrunning clutch problems. If the condition is advanced, an overhaul will be necessary to restore normal operation. A slipping clutch or band can often be determined by comparing which internal units are applied in the various gear ranges. The Clutch and Band Application chart provides a basis for analyzing road test results. Note that the rear clutch is applied in all forward ranges (D, 2, 1). The transmission overrunning clutch is applied in first gear (D, 2 and 1 ranges) only. The rear band is applied in 1 and R range only. Note that the overdrive clutch is applied only in fourth gear and the overdrive direct clutch and overrunning clutch are applied in all ranges except fourth gear. For example: If slippage occurs in first gear in D and 2 range but not in 1 range, the transmission overrunning clutch is faulty. Similarly, if slippage occurs in any two forward gears, the rear clutch is slipping. Applying the same method of analysis, note that the front and rear clutches are applied simultaneously only in D range third and fourth gear . If the transmission slips in third gear, either the front clutch or the rear clutch is slipping. If the transmission slips in fourth gear but not in third gear, the overdrive clutch is slipping. By selecting another gear, which does not use these clutches, the slipping unit can be determined. For example, if the transmission also slips in Reverse, the front clutch is slipping. If the transmission does not slip in Reverse, the rear clutch is slipping. If slippage occurs during the 3-4 shift or only in fourth gear , the overdrive clutch is slipping. Similarly, if the direct clutch were to fail, the transmission would lose both reverse gear and overrun braking in 2 position (manual second gear). If the transmission will not shift to fourth gear , the control switch, overdrive solenoid or related wiring may also be the problem cause.

Related Content:

ax4n clutch and band chart, replacing a torque converter clutch solenoid on a kia, honda pilot fix no reverse, torque converter cluch selenoid on 1999 odyssey, 47 no forward gears, cd4e application chart, How to fix f150 torque converter clutch solenoid, how test overdrive 46re wiring, ford cd4e gear chart, ford cd4e automatic gear chart

Burien Toyota 5SFE Turbo Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 17-06-2011

download
The following parts are not required, but you may want to have on hand: 9 Fresh Toyota engine coolant 9 New engine oil (preferably synthetic) and new Toyota oil filter 9 New parts to perform a tune-up (spark plugs, distributor cap & rotor). If you do replace your plugs, you may want to use a colder plug to reduce the chance of detonation. 9 New Ignition wires, if your current wires are old 9 New Toyota fuel filter (since you’re replacing the expensive injectors) 9 Shorter oil filter union from Toyota (See step #11) 9 Tie-wraps to secure vacuum lines (See step #27) 9 Shielded audio cable (See step #26.b) 9 For automatic transmissions, consider replacing the transmission fluid with a good synthetic brand and installing an ATF cooler. Burien Toyota 5S-FE Turbocharger Installation Manual Page 2 of 20Kit Contents ¾ Toyomoto exhaust manifold ¾ Garrett TB0344 turbo (Exhaust manifold and turbo charger come attached) ¾ Intermediate pipe (‘S’ shaped pipe with blow off valve attached) ¾ Down pipe (‘J’ shaped pipe with 90° bend and exhaust flange, also has mount for oxygen sensor) ¾ Turbo intake pipe (Usually attached to turbo) ¾ 90º elbow with valve cover breather hose attached (Elbow used to mount air filter) ¾ K&N air filter ¾ HKS Racing Blow-off/Pop-off valve ¾ (4) 360cc Toyota Injectors ¾ Toyota Oil pan ¾ Toyota MAP Sensor ¾ All necessary hoses, clamps, nuts, bolts, fittings, studs, gaskets and such required to install the system.

Related Content:

turbo m9

Related Content:

how to replace solenoid e on a245e transmission problems, yhs-lavasoft, gm 4l60e band adjustment screws, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, 2005 explorer transmission exploded view, how to check tranmission fluid on 2012 kia sedona, 2003 trailblazer torque converter removal, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio