Skip to content

1997 7 3 powerstroke manual

You search PDF repair manual about 1997 7 3 powerstroke manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.

1997-2006 Ford Explorer Sport 2-dr Overhead Console Modification Service Manual

download
Technical Service Bulletin Overhead Console Modification 1997-06 Explorer Sport 2-dr, 2001-06 SportTrac, 1996-01 Explorer 4-dr: Most moonroof and popup sunroof applications require no console modification. Spoiler sunroofs without flush motors require shortening the console. Simply cut the console at the last flip down pocket for a clean vertical wall (no cap required). The entire console is then easily covered in new cloth. Optional – make a cover plate and wrap just the plate in matching headliner cloth. Most full size sunroofs fit the flat spots between the ribs.

1996 – 2000 Civic 2-door Front Windows Bind or Have Come Out of the Run Channel Repair Manual

download
REPAIR PROCEDURE 1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual. 2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator. 3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot. 4. Check the year and VIN. If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5. If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8. 5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts. 6. Disconnect the power window motor connector, and detach the harness clip (if applicable); then lift and remove the regulator through the opening in the door. 7. Install the new regulator in the door, then loosely install the two rear mounting bolts and the two roller guide bolts. Do not tighten the two front mounting bolts yet. Go to step 9. 8. Loosen the window regulator’s two rear mounting bolts, two front mounting bolts, and two roller guide bolts

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP

download
TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL. 4 High and 4 Low, but not in 4 Auto. The 4 PLEASE REFER TO THE APPROPRIATE YEAR High mode is intended for severe winter EXPLORER SERVICE MANUAL FOR COMPLETE weather or off-road driving only. It is not LISTING AND EXPLANATION. intended for use on dry or merely wet pavement. 3. If any of the DTCs in the above Step 2 are set, remove the corresponding speed sensor and 2. Verify the instrument panel has the proper 4X4 replace accordingly. Drive the vehicle to verify if selection label (Figure 1). Proceed to 1995-97 the shudder/binding has been eliminated. Send Explorer heading, Step 1. replaced speed sensor to the Ford Warranty 1995-97 EXPLORER Parts Return Center, Canton, MI. NOTE 4. Using NGS Tester, monitor the Parameter 4 AUTO IS THE FAR LEFT SWITCH POSITION Identification Display (PID) on the transfer case ON 1997 MODELS AND IS THE MIDDLE clutch duty cycle. If the 4 Auto mode reads POSITION ON 1996 MODELS. something higher than one (1), verify speed sensors have not set any Generic Electronic 1. If during test driving, the vehicle shudders or Module (GEM) DTCs and follow the speed binds in 4 Auto during slow forward or reverse sensor diagnostic procedure in the above Step parking lot maneuvers, proceed to Step 2. 2. Verify the following while checking PID: Mode Duty Cycle Indicator 4 Auto 0 or 1 4 High 13 4 Low 38 at 5 MPH 5. If the speed sensor circuits are functional, inspect for water contamination in the transfer case oil

1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.