1997 ford explorer service manual torrent

You search PDF repair manual about 1997 ford explorer service manual torrent, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1997 ford explorer service manual torrent Direct Download speed 5432 Kb/s

  1997 ford explorer service manual torrent Full Version speed 8172 Kb/s



1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP

0

Filed Under (Ford Manuals) by admin on 20-01-2012

download
TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL. 4 High and 4 Low, but not in 4 Auto. The 4 PLEASE REFER TO THE APPROPRIATE YEAR High mode is intended for severe winter EXPLORER SERVICE MANUAL FOR COMPLETE weather or off-road driving only. It is not LISTING AND EXPLANATION. intended for use on dry or merely wet pavement. 3. If any of the DTCs in the above Step 2 are set, remove the corresponding speed sensor and 2. Verify the instrument panel has the proper 4X4 replace accordingly. Drive the vehicle to verify if selection label (Figure 1). Proceed to 1995-97 the shudder/binding has been eliminated. Send Explorer heading, Step 1. replaced speed sensor to the Ford Warranty 1995-97 EXPLORER Parts Return Center, Canton, MI. NOTE 4. Using NGS Tester, monitor the Parameter 4 AUTO IS THE FAR LEFT SWITCH POSITION Identification Display (PID) on the transfer case ON 1997 MODELS AND IS THE MIDDLE clutch duty cycle. If the 4 Auto mode reads POSITION ON 1996 MODELS. something higher than one (1), verify speed sensors have not set any Generic Electronic 1. If during test driving, the vehicle shudders or Module (GEM) DTCs and follow the speed binds in 4 Auto during slow forward or reverse sensor diagnostic procedure in the above Step parking lot maneuvers, proceed to Step 2. 2. Verify the following while checking PID: Mode Duty Cycle Indicator 4 Auto 0 or 1 4 High 13 4 Low 38 at 5 MPH 5. If the speed sensor circuits are functional, inspect for water contamination in the transfer case oil

Related Content:

1997 Ford Explorer Repair Manuals, 2011 Chevy Cruze P057c Code, 4 0l sohc timing position schematics, ford explorer Front Axle Clunking, pid default parmameters for 2007 ford explorer, po57c

1997-2006 Ford Explorer Sport 2-dr Overhead Console Modification Service Manual

0

Filed Under (Ford Manuals) by admin on 12-03-2012

download
Technical Service Bulletin Overhead Console Modification 1997-06 Explorer Sport 2-dr, 2001-06 SportTrac, 1996-01 Explorer 4-dr: Most moonroof and popup sunroof applications require no console modification. Spoiler sunroofs without flush motors require shortening the console. Simply cut the console at the last flip down pocket for a clean vertical wall (no cap required). The entire console is then easily covered in new cloth. Optional – make a cover plate and wrap just the plate in matching headliner cloth. Most full size sunroofs fit the flat spots between the ribs.

Related Content:

service manual for 2001 ford explorer

ALL INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 23-04-2012

download
SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. Groan noise during stopping: • Usually caused by glazing of the rotor’s surface as a result of heavy or frequent braking. • Refer to technical bulletins specific to the model of vehicle regarding this issue. • Replace the brake pads, then resurface the rotors and finish them with sand paper. Refer to Brake Service on page 5 for additional detail. Single clunk noise from front suspension when applying the brakes: • The noise is a result of the brake pads shifting in the direction of rotor rotation when the brakes are applied. Can be duplicated by lightly touching the brake pedal. • • If the brake pedal is pushed hard, the noise is less likely to occur. Make sure the brake pads and pad hardware (shims, springs, clips, etc) are installed correctly. Refer to ASIST for vehicle specific brake service information. Refer to Brake Service on page 5 for additional detail. Mull e he engine is started: • st er models, the self check occurs the first aches 5 mph after the engine is started. ors or drums. • WARNING: Brake dust may be hazardous if inhaled. Refer to the Service Manual (ESM) for brake • n and lubrication of brake pads, CAUTION: Do not get grease on the brake pad friction surface. A • Brake Judder is caused by rotor thickness variation and/or rotor run out.

Related Content:

manual for 1993 bmw 325i, lexus engine 2gr-fe chirping squeak noise sb0010-09, psc under hybrid highlander, titan 5500 generator manual, Free 98 Honda Accord service Repair Manual, gc25k service manual, Free Mercruiser 3 0 Service Manual, h22a service manual, motorcraftservice com, Honda Accord 1998-2002 Service Repair Manual free PDF

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

Acura MDX Torque Converter Shudder or Vibration Between 35 and 40 MPH Repair Manual

0

Filed Under (Acura Manuals) by admin on 24-11-2011

download
1. To confirm the client’s complaint, test-drive the vehicle on a smooth road, preferably with a slight incline. Set the cruise control between 35 and 40 mph, and monitor the engine rpm using the vehicle’s tachometer, or use the HDS to take a snapshot of the engine rpm. 2. If the engine speed fluctuates several hundred rpm while maintaining a constant vehicle speed, disconnect the EGR valve and retest the vehicle. •If the fluctuation is gone, refer to the EGR troubleshooting in the service manual. •If the engine rpm still fluctuates, and the transmission does not have any other symptoms (shifting problems, slipping, transmission DTCs) go to step 3. 3. Drain the transmission fluid, then strain it through a paint strainer. •If you find little or no contamination in the strainer, the ATF is OK, even if it smells burnt, is discolored, and/or the magnetic drain plug has small chips, flakes, or metal fuzz on it. Go to REPAIR PROCEDURE A . •If you find large amounts of contamination (pieces of metal or friction material) in the strainer, go to REPAIR PROCEDURE B . REPAIR PROCEDURE A 1. Remove the torque converter: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Install the torque converter: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 3. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 4. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are off. •Start the engine, and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes. REPAIR PROCEDURE B Follow the IN-WARRANTY EXCHANGE steps in service bulletin 90-009, Automatic Transmission In- Warranty Exchange Program , to order a remanufactured A/T, replace the failed A/T, and return the failed A/T core. 1. Remove the transmission: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Clean the transmission cooler. Refer to service bulletin 89-015, ATF Cooler Cleaner . 3. Install a remanufactured transmission: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 4. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 5. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off. •Start the engine and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes

Related Content:

1998 mazda MPV owners manual, 2002 ford thunderbird service manual, cd4e pdf atsg, freelander engine control module mobility module master, how much for torque converter for 2001 mdx, torque converter problems symptoms for 1999 3 2tl acura, what is a torque shudder

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 04-05-2012

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.

Related Content:

yhow to remove and install airbag for fored explorer sport trac, 2001 Sport Trac Manual Download, 2005 ford explorer code c2769, how to replace thermostat housing on 2003 ford sport trac 3 6liter, location of the GEM module 02 explorer, lube points on a 1997 thunderbird, overhead console sport trac fix, p0741 explorer 5r55e, rear window wont go up connector in sill plate 05 ram, remove rear pillar camry

1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 06-01-2012

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.

Related Content:

differential service procedures, 2006 suburban oil pump replcement procedure, picture of 1997 4x4 honda passport axle warning lights, 1997 dodge ram 4x4 1500 service manual download, oil pump leak 2003 accord, oil pump on a 307, oil punp removal 2002 trailblazer, rav4 rear oil leak, Toyota 4 Y oil pump, what causes 147 transaxle code on 97 e420 mercedes

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering

1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia

K40016 ADD-A-LEAF SPRING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 19-04-2012

download
CHEVY 1982-98 S Series all 2WD/4WD 1972-82 LUV PU 2 WD DODGE 1994-99 Ram 1500 2WD 1994-00 Ram 1500 4WD FORD 1990-96 F 150 std or ext cab 2WD 1982-89 F 150 std or ext cab 2WD 1983-1996 Ford Bronco II 4WD 1983-1996 Ford Bronco II 2WD 1983-1997 Ford Ranger 2WD/4WD 1990-00 Ford Ranger 2WD 1983-97 Ford Explorer 2WD/4WD 1972-84 Ford Courier 2WD K40016 ADD-A-LEAF SPRING KIT JEEP 1984-01 Jeep Cherokee 1974-86 CJ-5/CJ-7/CJ-8 4WD 1967-73 Jeepster/C101/C101 w multileaf Jeep Wrangler 1987-96 Front and Rear LAND ROVER 1959-1981 All 4wd MITSUBISHI 1986-91 Montero 1982-84 PU 2WD/4WD NISSAN 1968-1997 PU/Pathfinder 2WD/4WD TOYOTA 1963-98 Toyota PU/4 Runner with 2.5″ rear springs The K40016 Add-A-Leaf Spring Kit retrofits onto the following vehicles: The kit consists of two each 28″ Leaf Springs and two sets of two each longer bolts and nuts of different diameters. The same diameter bolt currently on the vehicle should be used and the other set discarded. • PLEASE READ ALL INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION • You must use 2-large “C-clamps” or a large vise to contain the elastic potential energy stored in a leaf spring when the center bolt is removed. • The new leaf spring will be placed in the existing spring assembly in a progressive pyramid shape. Example – if your number 1 Spring is 32″ long and the next one is 25″ long, the new Add-A-Leaf Spring should be place between them. • Some vehicles will have a flat helper stack. SEE ILLUSTRATION – DO NOT INSTALL THE NEW ADD-A-LEAF SPRING IN OR BELOW THE HELPER SPRIN(S). Helper spring assembly. Do not install Add-A-Leaf in or below this assembly Lowest allowable position for Add-A-Leaf

Related Content:

2003 ford escort vmm, 1969 ford truck ranger 390 overheating did not start till change water pump, fluid spec for 2004 ford ranger, f53 96 manual, 83 ranger wiring diagram, 1996 Ford RV specifications, 1996 Ford Explorer Repair Manual, 1996 ford explorer manual, 1996 f53 manifold exhaust repair, 1986 555b ford backhoe injector pump

Related Content:

1997 Ford Explorer Repair Manuals, 2011 Chevy Cruze P057c Code, 4 0l sohc timing position schematics, ford explorer Front Axle Clunking, pid default parmameters for 2007 ford explorer, po57c