Skip to content

1997 ford explorer transfer case removal

You search PDF repair manual about 1997 ford explorer transfer case removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP

download
TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL. 4 High and 4 Low, but not in 4 Auto. The 4 PLEASE REFER TO THE APPROPRIATE YEAR High mode is intended for severe winter EXPLORER SERVICE MANUAL FOR COMPLETE weather or off-road driving only. It is not LISTING AND EXPLANATION. intended for use on dry or merely wet pavement. 3. If any of the DTCs in the above Step 2 are set, remove the corresponding speed sensor and 2. Verify the instrument panel has the proper 4X4 replace accordingly. Drive the vehicle to verify if selection label (Figure 1). Proceed to 1995-97 the shudder/binding has been eliminated. Send Explorer heading, Step 1. replaced speed sensor to the Ford Warranty 1995-97 EXPLORER Parts Return Center, Canton, MI. NOTE 4. Using NGS Tester, monitor the Parameter 4 AUTO IS THE FAR LEFT SWITCH POSITION Identification Display (PID) on the transfer case ON 1997 MODELS AND IS THE MIDDLE clutch duty cycle. If the 4 Auto mode reads POSITION ON 1996 MODELS. something higher than one (1), verify speed sensors have not set any Generic Electronic 1. If during test driving, the vehicle shudders or Module (GEM) DTCs and follow the speed binds in 4 Auto during slow forward or reverse sensor diagnostic procedure in the above Step parking lot maneuvers, proceed to Step 2. 2. Verify the following while checking PID: Mode Duty Cycle Indicator 4 Auto 0 or 1 4 High 13 4 Low 38 at 5 MPH 5. If the speed sensor circuits are functional, inspect for water contamination in the transfer case oil

2003 Ford F-Super Duty 250-550/ Excursion Differential Case and Ring Gear Removal And Installation manual

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 4. Install the differential case on the special tool 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plate 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. 8. WARNING: Keep fingers/hands away from pinion gears when rotating the differential case with the differential rotating tool. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim. CAUTION: When separating the clutch plates and clutch discs, note the sequence in which they are disassembled. They must be reassembled in the same sequence. CAUTION: Do not use acids or solvents when cleaning the differential clutch pack. Wipe components with a clean, lint-free cloth only. Separate the differential clutch discs and clutch plates for cleaning and inspection. Refer to the disassembled view of the limited slip differential case in the Description and Operation portion of this section.

2000 Chevy Truck S10/T10 Blazer Transfer Case Removal And Installation Manual

download
Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case. 12. For vehicles equipped with a manual transmission, remove the six nuts securing the transfer case and bracket to the transmission 13. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 14. For vehicles equipped with a automatic transmission, remove the six nuts securing the transfer case and bracket to the transmission adapter. 15. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 16. Remove and discard the gasket. Installation Procedure 1. Install a new gasket to the transmission. Use sealer GM P/N 12346004 in order to hold the gasket in place. 2. Raise and position the transfer case to the vehicle Notice: Refer to Fastener Notice in Service Precautions. 3. For vehicles equipped with a automatic transmission, install the six nuts securing the transfer case and bracket to the transmission adapter. * Tighten the nuts to 47 Nm (35 lb ft) . 4. For vehicles equipped with a manual transmission, install the six nuts securing the transfer case and bracket to the transmission. * Tighten the nuts to 47 Nm (35 lb ft)

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.

1997-2006 Ford Explorer Sport 2-dr Overhead Console Modification Service Manual

download
Technical Service Bulletin Overhead Console Modification 1997-06 Explorer Sport 2-dr, 2001-06 SportTrac, 1996-01 Explorer 4-dr: Most moonroof and popup sunroof applications require no console modification. Spoiler sunroofs without flush motors require shortening the console. Simply cut the console at the last flip down pocket for a clean vertical wall (no cap required). The entire console is then easily covered in new cloth. Optional – make a cover plate and wrap just the plate in matching headliner cloth. Most full size sunroofs fit the flat spots between the ribs.