1997 ford ranger four wheel drive repair

You search PDF repair manual about 1997 ford ranger four wheel drive repair, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1997 ford ranger four wheel drive repair Direct Download speed 5432 Kb/s

  1997 ford ranger four wheel drive repair Full Version speed 8172 Kb/s



1997 Ford Aerostar/ Ranger Wheel Grease Seal and Bearing Front Replacement and Repacking

0

Filed Under (Ford Manuals) by admin on 20-11-2011

download
Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03 . 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03 . 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation

Related Content:

F550 wheel bearing torque, is the rear wheel bearing wet f350 97, replacing rear wheel bearing on 2006 escape, 2009 BUICL ENCLAVE WHEEL BEARING TORQUE, tools needed to change hub and bearing assembly on 2002 tahoe, f53 wheel bearing seal change, Toyota Tacoma Bearing Hub Assembly 2008 inside details, wheel bearing 2000 dodge dakota, isuzu npr wheel bearing installation, malibu direct drive ahaft greasing

2005 Ford F-150 Drive Pinion Flange and Drive Pinion Seal Repair Manual

0

Filed Under (Ford Manuals) by admin on 21-04-2012

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 . 2. Remove the brake disc. For additional information, refer to Section 206-04 . 3. Index-mark the driveshaft flange and pinion flange for correct alignment during installation. 4. Remove the 4 driveshaft flange bolts. 5. NOTE: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the driveshaft centering socket yoke from the pinion flange. Pry only in the area shown with a suitable tool to disconnect the driveshaft centering socket yoke from the pinion flange. Using a suitable tool as shown, disconnect the driveshaft centering socket yoke from the pinion flange. ? Using mechanic’s wire, position the driveshaft aside. 6. Using a Nm (lb-in) torque wrench on the pinion nut, record the torque required to maintain rotation of the pinion gear through several revolutions. 7. Using the special tool to hold the pinion flange, remove and discard the pinion nut.2005 F-150 Workshop Manual 8. Index-mark the pinion flange in relation to the drive pinion stem to make sure of correct alignment during installation. 9. Using the special tool, remove the pinion flange. 10. Force up on the metal flange of the drive pinion seal. Install gripping pliers and strike with a hammer until the drive pinion seal is removed. Installation 1. Lubricate the new drive pinion seal with grease. 2. Using the special tool, install a new drive pinion seal. 3. Lubricate the pinion flange splines with axle lubricant. 4. NOTE: Disregard the scribe marks if a new pinion flange is being installed. Align the pinion flange with the drive pinion shaft. 5. Using the special tool, install the pinion flange. 6. l a new pinion nut with the same iginal if not replacing the collapsible spacer. If a installed, install the nut in the kit, as indicated in the chart below, or damage to the component may occur. Position the new pinion nut. Pinion Nut 7. no circumstances ut to be backed off to reduce drive pinion bearing preload. If reduced drive pinion bearing preload is required, a new drive pinion collapsible spacer and pinion nut must be installed or damage to the component may occur. NOTE: Remove the special tool while taking drive pinion bearing preload readings with the Nm (lb-in) torque wrench. Using the special tool to hold the pinion flange, tighten the pinion nut. ? Rotate the drive pinion occasionally to make sure the drive pinion bearings are seating correctly. ? Install a Nm (lb-in) torque wrench on the pinion nut. ? Rotating the drive pinion through several revolutions, take frequent drive pinion bearing preload readings until the original recorded drive pinion bearing preload reading is obtained. ? If the original recorded drive pinion bearing preload is lower than specification, tighten to the appropriate specification for used drive pinion bearings. If the drive pinion bearing preload is higher than specification, tighten the pinion nut to the original reading as recorded. For additional information, refer to the Specification portion of this section. 8. Position the driveshaft and align the index mark on the pinion flange.

Related Content:

guide differential f53 1997, replacing 94 camaro rack and pinion, how to repair noise driveshaft in a ford expedicion 2001, cummins n14 accessory drive torque specs, cost to replace a rack and pinion on 2002 suburban, 2004 ford f150 yoke, meritor pinion seal installer, mercedes exhaust pipe torque spec, mercury drive shaft socket, how to change rack and pinion 05trailblazer

Toyota T50 5 Speed Transmission Electronic Speedo Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 19-04-2012

download
I have intentionally left the photos large, to try to clarify any detail I did not explain in the text. This modification DOES require the use of a lathe, I have tried to write it so as to allow you to go to your local machine shop, brother in law, mate or anyone with a lathe…and it will be done correctly Much thanks to John O’Rielly (PLAGER 7) in Brisbane for passing on the information and problems he had with this modification. Fig.1Standard Drive Assemblies T50 left and AE101 right T50 Speedo Drive Adaption Rev 1 Feb 2003 2 Step One:- Dissassembly T50 Drive:- Disassembly is simple, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” ring from the housing. Wash all parts internally and externally to remove oil, grease and road grime. Fig.2 T50 Drive Disassembled T50 Speedo Drive Adaption Rev 1 Feb 2003 3 AE101 Drive:- Disassembly is similar to T50, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” rings from the housing. Remove the three (3) philips head screws from the cover on the top of the drive housing. Carefully remove cover, be aware that the small parts in side may be stuck to the cover. Remove all internal parts, record order of assembly. Wash housing and shaft to remove oil, grease and road grime. Fig.3 AE101 Drive Disassembled T50 Speedo Drive Adaption Rev 1 Feb 2003 4 Step Two:- Shortening the Drive Shaft Drive Shaft:- The T50 drive shaft needs to be shortened to a similar length to the AE101. I reassembled the AE101 shaft and housing, and then measured from the top face of the AE101 housing down to the top of the AE101 drive shaft. ( Fig.4) Record this reference depth, (I got 17mm) . Fig.4 Drive Shaft Depth Std AE101 Shaft & Housing The T50 drive shaft will need to be shortened to give the same depth as measured in Fig.4. When I did mine, (and a few others), I found I needed the T50 shaft to be 68.0mm long. Fig.5 Fig.6 The drive shaft is hardened, so I used a belt linisher to shorten the shaft, it could as easily be done on a fine grinding wheel. Remember slowly does it, regular checks of depth in housing and do not let the shaft get too hot during grinding/linishing, this will affect the heat treatment and consequently affect the strength of the drive dogs on the shaft end. Carefully deburr and chamfer, end detail should be similar to original AE101

Related Content:

ax4n endplay specification, manually disengage 4 wheel drive in durango, 1997 dodge ram 1500 tailshaft diagram, 2008 ford f150 driveshaft, repairing rear pinion oil seal 2002 ford explorer sport trac 2wd, expidition drive shaft retaining bolts, drive cycle for toyota corolla 2001, Driveshaft for 2002 Ford F-150 diagram, toyota tundra 2000 4 wheel drive diagnosis, 08 KIA SORRENTO CENTER BEARING

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

0

Filed Under (Chevrolet Manuals) by admin on 27-06-2012

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

Related Content:

wheel bearing 2004 Mountaineer, 2004 CHEVY SILVERADO TCCM, 09 silverado front axle diagram, saturn ion 3 2006 wheel nut torque, torque on 2000 tahoe front brake parts, manual silverado z71 2004, repair manual for a 95 chevy silverado, torque specs for Tahoe wheel bearing bolt, tourque specs 2003 chev truck 1500 wheels, what size is wheel hub lock nut on 2008 sierra denali

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, how to replace wheel bearings on a 08 silverodo, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, snap ring assemble, Need to torque specifications 1999 GMC 1500 wheel hub bearings, 1977 ford f-350 rear wheel diagram, 2009 impala hub mounting bolt torque, removing rear wheel bearing race on 06 ford f-250, removing wheel bearing off a 2009 ford ranger rear axle

FORD Wheel Bearings REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 16-05-2011

download
Removal & Installation Installation Installation Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle”to”wheel hub retainer nut and washer. 3. Remove the parking brake shoes. 4. Press the outboard CV”joint until it is loose from the hub. 5. Remove and discard the toe link”to”wheel knuckle nut. 6. Remove the bolt and separate the toe link from the wheel knuckle. 7. Remove and discard the upper arm”to”wheel knuckle nut. 8. Remove the bolt and separate the upper arm from the wheel knuckle. 9. Remove and discard the lower arm”to”wheel knuckle nut. ? ? WARNING Do not use a hammer to separate the outboard CV”joint from the hub. Damage to the threads and internal CV”joint components can result. ? ? WARNING Do not damage the boot while separating the toe link from the wheel knuckle. ? ? WARNING Do not damage the boot while separating the ball joint from the wheel knuckle. ? ?
To To To To install: install: install: install: 10. Remove the lower arm”to”wheel knuckle bolt. 11. Remove the wheel knuckle. 12. Using a suitable press, remove and discard the wheel hub. 13. Remove and discard the wheel bearing retainer ring. 14. Using a suitable press, remove the wheel bearing

Related Content:

1999 Toyota Prius head torque specifications, 1995 f150 4x4 alignment specfications, what is the wheel torque on a 2013 ford taurus, service manuel cwb-1742 wheel alignment, mazda 3 wheel torque, lug nut torque 2000 Ford E450, How to Read Alignment Specs, how to do a rough tire allignment, 2007 mazda 3 front axle nut torque, 1999 infiniti g20 front axle lug nuts

2009 Cadillac CTS AWD Front Wheel Drive Shaft Replacement – Left Side

0

Filed Under (Cadillac Manuals) by admin on 16-05-2011

download
Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle ( See: MaintenanceVehicle LiftingService and Repair ). 2. Remove the left front tire and wheel. Refer to Tire and Wheel Removal and Installation ( See: MaintenanceWheels and TiresService and Repair ). 3. Remove the left outer tie rod from the steering knuckle. Refer to Steering Linkage Outer Tie Rod Replacement (All Wheel Drive) ( See: Steering and SuspensionSteeringTie RodService and RepairSteering Linkage Outer Tie Rod Replacement )Steering Linkage Outer Tie Rod Replacement (Rear Wheel Drive) ( See: Steering and SuspensionSteeringTie RodService and RepairSteering Linkage Outer Tie Rod Replacement ). 1. Install the new O-ring (2) on the intermediate shaft. 2. Install the new retaining ring (1) on the intermediate shaft. 3. Apply a small amount of grease GM P/N 01051344 (Canadian P/N 993037) or equivalent to the intermediate wheel drive shaft splines. 4. Install the left front wheel drive shaft in the intermediate shaft. 5. To ensure that the wheel drive shaft is installed properly, grasp the inner tripod housing and pulling it outward. DO NOT pull on the axle shaft . 6. Install the wheel drive shaft in the front knuckle. 7. Install the left upper control arm on the knuckle. Refer to Upper Control Arm Replacement ( See: Steering and SuspensionSuspensionControl ArmService and RepairRear SuspensionUpper Control Arm Replacement

Related Content:

2012 gm awd tire replacement guideline

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

555 ford backhoe repair manual, ford 9 inch repair manual, How to Fix Po446 Code ford escape xls, Ford E 450 Cutaway Manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, heaf bolt torque specs 655a backhoe, windstar dtc u1131

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2005 Scion TC Manual PDF, 2006 odyssey p0741 code, 2004 LINCOLN AVIATOR TRUCK SUV Service Shop Repair Manual pdf, 2005 nissan maxima fuse box location, ford e450 repair manual torrent, 2005 mercury mariner carrier bearing, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, head suction drain adapter crownline 240ex, 2005 expedition repair manual

2004 Honda CIVIC Maintenance Schedule for Severe Conditions

0

Filed Under (Honda Manuals) by admin on 25-02-2011

download
30,000 miles/ 48,000 km/ — Service at the indicated distance or time, whichever comes first. Use this schedule if the vehicle is driven MAINLY in Canada or in any of the following conditions; if only OCCASIONALLY driven in these conditions, use the Normal Conditions schedule. Severe Driving Conditions ?Driving less than 5 miles (8 km) per trip in freezing temperatures, or driving less than 10 miles (16 km) per trip. ?Driving in extremely hot (over 90 ºF/32 ºC) conditions. ?Extensive idling, or long periods of stop-and-go driving, such as a taxi or a commercial delivery vehicle. ?Driving on muddy, dusty, or de-iced roads. ?Trailer towing, driving with a roof rack, or driving in mountainous conditions. Severe Driving Conditions ?Driving less than 5 miles (8 km) per trip in freezing temperatures, or driving less than 10 miles (16 km) per trip. ?Driving in extremely hot (over 90 ºF/32 ºC) conditions. ?Extensive idling or long periods of stop-and-go driving, such as a taxi or a commercial delivery vehicle. ?Driving on muddy, dusty, or de-iced roads. ?Trailer towing, driving with a roof rack, or driving in mountainous conditions. Do the items in parts A, B, C, D, E, F, G, H, I, and J as required for the mileage/time interval listed. NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk (*) will not void the customer’s emissions warranties. However, Honda recommends that all maintenance services be done at the recommended intervals to ensure long-term reliability. ? Replace engine oil, every 5,000 miles (8,000 km) or 6 months. ? Engine oil capacity-D17A1 engine without oil filter: 3.0 L (3.2 US qt), D17A2 and D17A6 engines without oil filter: 3.3 L (3.5 US qt). ? Replace engine oil filter, every 10,000 miles (16,000 km) or 1 year. ? Engine oil capacity-D17A1 engine with oil filter: 3.2 L (3.4 US qt), D17A2 and D17A6 engines with oil filter: 3.5 L (3.7 US qt). ? Check front and rear brakes, every 10,000 miles (16,000 km) or 1 year. ?Check pads and discs for wear (thickness), damage, and cracks. ?Check calipers for damage, leaks, and tightness of mount bolts. ?Check wheel cylinders for leaks. ?Check brake linings for cracking, glazing, wear, or contamination. ? Lubricate all hinges, locks, and latches, every 10,000 miles (16,000 km) or 1 year. ? Rotate tires, and check tire inflation and condition, every 10,000 miles (16,000 km). ? Follow the pattern shown in the Owner’s Manual. ? Inspect tie rod ends, steering gearbox, and gearbox boots, every 10,000 miles (16,000 km) or 1 year. ?Check rack grease and steering linkage. ?Check boots for damage and leaking grease. ?Check fluid lines for damage and leaks. ? Inspect suspension components, every 10,000 miles (16,000 km) or 1 year. ?Check bolts for tightness. ?Check condition of ball joint boots for deterioration and damage

Related Content:

2007 honda accord 10000 mile, 2011 kia sorento 50 000 maintenance, 2012 honda crv maintenance guide, honda crv 2011 maintenance schedule, required 2004 honda accord maintenance, saturn ion routine maintenance pdf

Related Content:

F550 wheel bearing torque, is the rear wheel bearing wet f350 97, replacing rear wheel bearing on 2006 escape, 2009 BUICL ENCLAVE WHEEL BEARING TORQUE, tools needed to change hub and bearing assembly on 2002 tahoe, f53 wheel bearing seal change, Toyota Tacoma Bearing Hub Assembly 2008 inside details, wheel bearing 2000 dodge dakota, isuzu npr wheel bearing installation, malibu direct drive ahaft greasing