toyota tacoma valve cover gasket replacement

You search PDF repair manual about toyota tacoma valve cover gasket replacement, if there are search results will appear below. If search results do not exist, please search by others keyword.



  toyota tacoma valve cover gasket replacement Direct Download speed 5432 Kb/s

  toyota tacoma valve cover gasket replacement Full Version speed 8172 Kb/s



2005-2007 Toyota Tacoma L4-2.7L Intake Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 19-02-2012

download
Complete kit. Verify all components are present prior to beginning installation. Step 1 Remove the three 12mm bolts securing the lower air box. Remove the bolt securing the windshield washer reservoir. Remove the lower air box. Step 6 Place the “L” bracket on the valve cover. Secure with the factory bolt. Secure the VSV with the supplied hardware. Step 11 Complete stock intake. Step 2 Disconnect the breather hose and the vacuum hose connected to the intake resonator. Loosen the clamp on the throttle body. DONOTREMOVEINTAKE RESONATOR AT THIS TIME. Step 7 Remove the three bolts that secure the intake resonator to the valve cover. Loosen the intake hose clamps. Step 3 Remove the VSV located on the back side of the intake resonator. Remove intake resonator. Step 8 Remove the intake hose. Step 4 Transfer the MAF sensor to the new intake tube with nylon spacers, screws, and gasket provided. Step 9 Disconnect the MAF sensor and remove the upper air box and air filter. Step 5 Install 3/4″ trim seal to housing. Secure the housing to the engine compartment with M8 screws and washers provided. Step 10 Tools Required 5/16″ nut driver or slotted screwdriver 10mm socket or wrench 12mm socket or wrench 13mm socket or wrench Ratchet and extension Part List: 1 Air filter (replacement # 24-90023) Pro Dry STM 21-90023 1 Intake Tube 1 Housing 1 Coupler, Straight 3″ x 3″ 1 Coupler, Hump 4″ x 3″ 2 Clamp #064 2 Clamp #048 2 Screw, MAF Sensor Mnt. 1 5/32″ Vent Hose x 8.5″ 1 “L” Bracket 2 Clamps, #008 1 5/8″ Vent Hose x 8″ 1 Fitting, Plastic 2 Screws, Hex M6 x 1 x 12 2 Nuts, M6 2 Washer, Wavy M6 1 Grommet 1 Gasket, MAF Sensor 3 Screws, Hex M8 3 Washers, Flat 1/4 2 Spacers, Nylon 1 Brass, Nipple 1 3/4″ Seal Trim x 21″ P.O. Box 1719 Corona, CA 92879 Support: 951-493-7100 www.aFepower.com Place couplers and clamps on tube and install. Install grommet and plastic fitting into tube. Now install into vehicle. Install small 5/32″ hose to vacuum line and brass fitting supplied. Install crank case hose with mini clamps provided and tighten to tube. Tighten all clamps. Reconnect the MAF sensor harness. Install air filter into housing and tighten using 5/16″ nut driver. The installation is now complete. Check all clamps and connection. Periodically check all clamps and hoses. Thank you for choosing aFe

Related Content:

2005 toyota tacoma 2 7l valve cover bolts torque, how to remove 2000 toyota tacoma air intake, how to replace 2005 tacoma 2 7l valve cover gasket, to remove air vent from 05-11 tacoma

2005-2007 Toyota Tacoma Intake Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 25-11-2011

download
Step 1 Remove the three 12mm bolts securing the lower air box. Remove the bolt securing the windshield washer reservoir. Remove the lower air box. Step 6 Place the “L” bracket on the valve cover. Secure with the factory bolt. Secure the VSV with the supplied hardware. Step 11 Complete stock intake. Step 2 Disconnect the breather hose and the vacuum hose connected to the intake resonator. Loosen the clamp on the throttle body. ONOTREMOVEINTAKE RESONATOR AT THIS TIME. Step 7 Remove the three bolts that secure the intake resonator to the valve cover. Loosen the intake hose clamps. Step 3 Remove the VSV located on the back side of the intake resonator. Remove intake resonator. Step 8 Remove the intake hose. Step 4 Transfer the MAF sensor to the new intake tube with nylon spacers, screws, and gasket provided. Step 9 Disconnect the MAF sensor and remove the upper air box and air filter. Step 5 Install 3/4″ trim seal to housing. Secure the housing to the engine compartment with M8 screws and washers provided. Step 10 Tools Required 5/16″ nut driver or slotted screwdriver 10mm socket or wrench 12mm socket or wrench 13mm socket or wrench Ratchet and extension Part List: 1 Air filter (replacement # 24-90023) Pro Dry STM 21-90023 1 Intake Tube 1 Housing 1 Coupler, Straight 3″ x 3″ 1 Coupler, Hump 4″ x 3″ 2 Clamp #064 2 Clamp #048 2 Screw, MAF Sensor Mnt. 1 5/32″ Vent Hose x 8.5″ 1 “L” Bracket 2 Clamps, #008 1 5/8″ Vent Hose x 8″ 1 Fitting, Plastic 2 Screws, Hex M6 x 1 x 12 2 Nuts, M6 2 Washer, Wavy M6 1 Grommet 1 Gasket, MAF Sensor 3 Screws, Hex M8 3 Washers, Flat 1/4 2 Spacers, Nylon 1 Brass, Nipple 1 3/4″ Seal Trim x 21″ P.O. Box 1719 Corona, CA 92879 Support: 951-493-7100 www.aFepower.com Place couplers and clamps on tube and install. Install grommet and plastic fitting into tube. Now install into vehicle. Install small 5/32″ hose to vacuum line and brass fitting supplied. Install crank case hose with mini clamps provided and tighten to tube. Tighten all clamps. Reconnect the MAF sensor harness. Install air filter into housing and tighten using 5/16″ nut driver. The installation is now complete. Check all clamps and connection. Periodically check all clamps and hoses. Thank you for choosing aFe

Related Content:

2005 toyota tacoma 2 7l valve cover bolts torque, how to remove 2000 toyota tacoma air intake, how to replace 2005 tacoma 2 7l valve cover gasket, to remove air vent from 05-11 tacoma