1998 ford expedition head gasket repair

You search PDF repair manual about 1998 ford expedition head gasket repair, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1998 ford expedition head gasket repair Direct Download speed 5432 Kb/s

  1998 ford expedition head gasket repair Full Version speed 8172 Kb/s



2001 Pontiac Sunfire L4-2.2L VIN 4 Cylinder Head Removal And Installation Manual

0

Filed Under (Pontiac Manuals) by admin on 11-06-2012

download
Cylinder Head Replacement * Tools Required * J28467-360 Engine Support Fixture * J36660-A Torque Angle Meter. Removal Procedure 1. Disconnect the negative battery cable. 2. Relieve the fuel system pressure. 3. Drain cooling system . 4. Remove the alternative fuel module assembly. Remove the drive belt . 5. Remove the air cleaner outlet duct and resonator assembly. 6. Support engine using floor jack and block of wood. 7. Remove the engine mount . 3. Remove the intake manifold . 9. Remove the exhaust manifold 10. Disconnect the Engine Coolant Temperature Sensor ( ECT ) electrical connection. 11. Remove the valve rocker arm cover. Important: When removing valve train components keep them in order. Do this to ensure that the components are installed in the same locations and with the same mating surfaces as when removed. 12. Remove the rocker arms and pushrods. 13. Remove the generator. 14. Remove the generator rear brace. 15. Remove the power steering pump. Position the pump aside with the lines attached. 16. Remove the radiator inlet pipe. 17. Remove the ignition coil assembly. 18. Remove the accessory bracket. 19. Disconnect the secondary ignition wires from the spark plugs . 20. Remove the cylinder head bolts. 21. Remove the cylinder head. 22. Clean the following components: * Head gasket surface * Valve rocker arm cover gasket surface * Threads Installation Procedure Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin

Related Content:

01 sunfire head gasket, 2004 kia sorento head gasket, 02 Buick rendezvous head gasket install you tube, What all should be done to a Pontiac Montana when fixing a head gasket leak?, how to remove a kia 2 7 bakkie 2007 model air manifold gasket, how to replace saab 93 turbo head gasket, i changed the head gasket on my 2005 buick rendezvous now motor is shaking, installing 400 pontiac heads, labor time 2002 f150 head gaskets, pontiac 7k3 heads

1999 Ford Escort/ Tracer Cylinder Head Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-04-2012

download
Removal 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 2. WARNING: Fuel supply lines will remain pressurized for long periods of time after engine shut down. This pressure must be relieved before disconnecting any fuel lines or fuel system components. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Remove the engine air cleaner outlet tube. For additional information, refer to Section 303-03 . 4. Remove the timing belt. For additional information, refer to Timing Drive Components—Timing Belt in this section. 5. Remove the vacuum hoses at the: * positive crankcase ventilation (PCV) valve (6A666). * throttle body (9E926). * intake manifold (9424). * fuel pressure sensor. 6. Disconnect the fuel charging wiring (9D930) electrical connectors at main engine connector. 7. Disconnect the crankshaft position (CKP) sensor electrical connector. 8. Disconnect the fuel line. For additional information, refer to Section 303-04 . 9. Remove the power steering pump (3A674) and bracket as an assembly. For additional information, refer to Section 211-02 . 10. Remove the generator (GEN). For additional information, refer to Section 414-02 . 11. Remove the oil level indicator tube (6754). For additional information, refer to Oil Level Indicator and Tube in this section. 12. Disconnect the heater hoses. For additional information, refer to Section 412-02 . 13. Lower the vehicle. 14. Disconnect the upper radiator hose (8260) from the thermostat housing water hose connection. For additional information, refer to Section 303-03 . 15. Remove the camshafts (6250). For additional information, refer to Camshaft in this section. 16. Remove the ignition coil (12029) and bracket. For additional information, refer to Section 303-07 . 17. Remove the water thermostat housing. For additional information, refer to Section 303-03 . 18. Disconnect the knock sensor electrical connector. 19. Remove the generator bracket-to-cylinder head bolt. 20. Remove the bolts and the cylinder head (6049). 21. Remove the cylinder head gasket and discard. Installation WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and may be ignited, resulting in possible personal injury. 1. CAUTION: Do not use abrasive grinding discs to remove gasket material; use only plastic manual scrapers. Do not scratch or gouge the aluminum sealing surfaces. Clean all gasket material from the mating surfaces on the cylinder head and cylinder block. Clean out the bolt holes in the cylinder block. Inspect the cylinder head for flatness. For additional information, refer to Section 303-00 . 2. Install a new head gasket on the cylinder block. 3. CAUTION: Do not attempt to install the cylinder head assembly without assistance. Installation of the cylinder head assembly requires two people or possible injury may occur. CAUTION: The bolts are torque-to-yield and must be replaced or engine damage may occur. Tighten the bolts in three stages in the sequence shown. * Stage 1: Tighten the bolts to 15-25 Nm (12-18 lb-ft). * Stage 2: Tighten the bolts to 35-45 Nm (26-33 lb-ft). * Stage 3: Tighten the bolts an additional 105 degrees. 4. Install the generator bracket-to-cylinder head bolt. * Tighten to 20 Nm (15 lb-ft). 5. Connect the knock sensor electrical connector. 6. Install the thermostat housing. For additional information, refer to Section 303-03 . 7. Install the ignition coil and bracket. For additional information, refer to Section 303-07 . 8. Install the camshafts. For additional information, refer to Camshaft in this section. 9. Connect the upper radiator hose. For additional information, refer to Section 303-03 . 10. Raise and support the vehicle. For additional information, refer to Section 100-02 . 11. Install the heater hoses. For additional information, refer to Section 412-02 . 12. Install the generator and bracket assembly. For additional information, refer to Section 414-02 . 13. Install the power steering pump and bracket assembly. For additional information, refer to Section 211-02 . 14. Connect the fuel lines. For additional information, refer to Section 310-00 . 15. Connect the crankshaft sensor electrical connector.

Related Content:

fleetwood sedona manuals, Honda Civic 2003 number #3 Cylinder pattern, 2001 mitsubishi 3 0 cylinder torque specs, Workshop Manual (WSM) Section 303-04, 4 8 head bolt tightening sequence, workshop information system saab, where is the knock sensor on a 2006 toyota tundra 4 7 v-8 truck, trailblazer front frame section, throttle postioning system in ford five hundred, pdf Ford manual Section 501-02

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, Replacing the reverse band Dodge 1500, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, repair manual for 1998 chevrolet 1500, downloadable schematic for 99 Chevy suburban evap system, ax12-1500 nut torque, 2010 silverado 1500 4 3 liter canister vavle solenoid, how to replace actuator on 2005 chevy 1500, lifter repair on 02 avalanche

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual

2001 Ford Truck F 150 Engine – Spark Plug Hole Thread Repair Procedure

0

Filed Under (Ford Manuals) by admin on 26-04-2012

download
SERVICE PROCEDURE Ford Motor Company now authorizes LOCK-N-STITCH aluminum insert and tool kit as a proper repair procedure. Follow the procedure included in the tool kit for using the tools and inserts. Tool kits and inserts can be ordered from Rotunda by calling 1-800-Rotunda (768- 8632). Choose option two (2), part number 302-00001. NOTE FORD MOTOR COMPANY HAS DETERMINED THAT REPAIRS MADE WITH THESE ALUMINUM INSERTS AND LOCK-N-STITCH TOOLS DO NOT AFFECT THE HEAT TRANSFER FUNCTION BETWEEN THE SPARK PLUG AND THE CYLINDER HEAD. NOTE THIS PROCEDURE IS NOT AUTHORIZED AS A FORD WARRANTY REPAIR. FOR VEHICLES WITHIN WARRANTY, REPLACEMENT OF THE CYLINDER HEAD IS RECOMMENDED. NOTE THIS IS THE ONLY FORD AUTHORIZED PROCEDURE FOR SPARK PLUG THREAD REPAIRS. NOTE THIS PROCEDURE IS AUTHORIZED FOR ESP REPAIRS AND RETAIL REPAIRS. WARRANTY STATUS: Information Only – Not Warrantable

Related Content:

2001 ford taurus repair manual, 2001 Ford Excursion Manual, ford focus 2001 repair manual, ford focus 2001 manual free, F53 King pin specs, cost to replace cooling sydtem taurus, 2010 ford f150 sunroof parts, 2010 ford f 150 lariat sunroof repair, 2001 ford sport trac rear window wont go up, 2001 Ford Ranger EdgeV6 owners manuel

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 2006 ford focus ses repair manual, 1999 chevy S10 - manual, cft30 scan codes, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, 1999 cavalier A/C instructions, 95 ford ranger owners mqnual, pdf 97 ford ranger, 1998 ford escort auto repair manual free

1995 Ford Truck F 150 2WD Pickup New Cylinder Head Bolt Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-02-2012

download
ORQUE SPECIFICATIONS FOR THE NON-FLANGED STANDARD HEX HEAD BOLTS, TIGHTEN IN TWO (2) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 75-88 N-m (55-65 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 88-98 N-m (65-72 lb.ft.). FOR ALL TORQUE TO YIELD HEX HEAD BOLTS, TIGHTEN IN THREE (3) STEPS AS FOLLOWS: 1. Tighten all bolts in sequence (Figure 2) to 34-47 N-m (25-35 lb.ft.). 2. Tighten all bolts in sequence (Figure 2) to 61-75 N-m 45-55 lb.ft.). 3. Tighten all bolts in sequence (Figure 2) an additional 1/4 turn (85-95 degrees). NOTE: WHEN THE CYLINDER HEAD BOLTS HAVE BEEN TIGHTENED FOLLOWING THESE PROCEDURES, IT IS NOT NECESSARY TO RETIGHTEN THE BOLTS AFTER EXTENDED OPERATION. CAUTION: TORQUE-TO-YIELD CYLINDER HEAD BOLTS MUST BE REPLACED WITH NEW BOLTS. DO NOT REUSE TORQUE-TO-YIELD BOLTS. TORQUE-TO-YIELD BOLTS MAY ONLY BE USED ONE (1) TIME. PART NUMBER PART NAME F3ZZ-6065-E Cylinder Head Bolt

Related Content:

1999 2 5 ford ranger head bolt torque, D-17 manfold bolt torqe, ranger 1999 3 0 head torque diagram, torque angle specs 3100 1998 buick, torque sequence 300m 3 5 heads

2000-2004 Toyota Tundra 4.7L V-8 Two and Four Wheel Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 27-03-2012

download
1. Place vehicle in a location where the floor is solid and flat, with adequate lighting. Do not attempt to work on a hot engine. Heat causes metal to expand and makes removal of fasteners difficult at best. Disconnect the battery cables from the battery. Raise the front of the vehicle to obtain adequate access to the bottom exhaust manifold flanges. Use large-base jack stands to support the vehicle. Do not rely on the jack! Block the tires to prevent the vehicle from rolling off the jack stands. 2. Spray WD-40 or some type of penetrating oil on all accessible fasteners and fittings before attempting to remove them. 3. From underneath the vehicle disconnect the exhaust system from the exhaust manifolds by unbolting the (3) bolts at the collectors. Then unbolt the driver side catalytic converter from the exhaust assembly and temporarily remove it from the vehicle. PASSENGER SIDE 4. On the passenger side remove the (4) bolts attaching the heat shields to the factory manifold. 5. Next, carefully unplug the O2 sensor from its harness. 6. Now remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 7. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 8. Transfer the O 2 sensor from the factory manifold to the new passenger side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 9. Now you are going to install the new JBA Header, but first there is some preparation of the hardware required. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. DRIVER’S SIDE 10. Just like you did in step (4) remove the (4) bolts attaching the heat shields to the driver side factory mani- fold. 11. Next, carefully unplug the O2 sensor from its harness. Unbolt the dipstick bracket from the head and remove the dipstick tube. 12. Remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 13. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 14. Transfer the O 2 sensor from the factory manifold to the new driver side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 15. As you did on the passenger side, prepare the hardware before installing the driver side header. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. Re-install the dipstick tube. 16. Install the driver side catalytic converter. 17. Connect the exhaust system to the new headers using hardware and gaskets supplied. Reconnect O2 sensors. 18. Check to insure adequate clearance between header and shifter cable (small cable that runs from firewall, to brace on fender well, to transmission) . More clearance can be gained by adjusting (bending) brace on fender well. 19. Recheck everything

Related Content:

2004 honda civic head bolt torque, 4y toyota head torque

2009 Ford Escape 3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/ THUMP NOISE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 25-01-2012

download
3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/THUMP NOISE This article supersedes TSB 09-11-6 to update the b. Isolate noise to LH – Listen to the cylinders Service Procedure and Part List. 4 and 6 valve cover fasteners (number 6 is by the coolant pump). There will be a ISSUE significant difference in transmitted noise Some 2009 Escape and Mariner vehicles, equipped between the cylinder 4 and 6 fasteners with 3.0L engine, may exhibit an intermittent when noise is present. Noise from LH – go knocking or thumping type noise from the cylinder to Step 4. head. After engine temperature reaches 210-220 °F NOTE (99-104 °C), the noise is typically heard from the THE RH AND LH NOISES HAVE DIFFERENT rear of the engine as the vehicle comes to a stop. CAUSES. FOLLOW ALL STEPS CAREFULLY FOR An example would be coming to a stop at the end PROPER DIAGNOSIS AND REPAIR. of a highway exit ramp. Noise will continue 45-60 seconds and then diminish. Noise will occur again 3. Replace the RH cylinder head per Workshop once engine reaches 210-220 °F (99-104 °C) and Manual (WSM), Section 303-01B. vehicle comes to another stop. a. Verify repair by repeating Step 2. If noise is ACTION still present then proceed with normal Follow the Service Procedure steps to correct the engine NVH diagnostics per WSM, Section condition. 100-04. SERVICE PROCEDURE 4. Remove LH valve cover. Refer to WSM, Section 303-01. 1. Is noise a 45-60 second knock/thump from a hot engine as the vehicle comes to a stop? a. Rotate the engine clockwise until cylinder number 6 exhaust cam lobes are pointing a. Yes – Go to Step 2. up and valves are fully closed. Exhaust camshaft needs to be left in this position for b. No – Stop as this procedure does not apply. all bearing caps in Step 4b. (Figure 1) Proceed with normal Workshop Manual (WSM), Section 100-04 diagnostics. 2. Using Chassis Ears, isolate the noise to Right Hand (RH) (Bank 1) or Left Hand (LH) (Bank 2) cylinder head. Noise is typically heard as 45-60 second knock/thump as the vehicle comes to a stop after engine reaches 210-220 °F (99-104 °C). a. Isolate noise to RH – Listen to the cylinder head by the variable camshaft timing (VCT) solenoid connectors. There will also be a vibration felt at the VCT solenoid connector when noise is present. Noise from RH – go to Step 3.

Related Content:

02 kia rio 1 5 will idle no accelaration, 2013 f-150 click noise at stop and start, causes of ford escape 2001 engine vibration, 2005 tundra tailgate noisey, ticking noise and misfire 4 8 litre gmc, chevy silverado catalytic converter 2004 v6 knocking tapping noise, Ford Escape motor mount removal and installation how to, GMC noise when brakes applied or released, how do i change the VCT solenoids on 2009 ford escape, installing engine in a 2008 ford escape

Related Content:

01 sunfire head gasket, 2004 kia sorento head gasket, 02 Buick rendezvous head gasket install you tube, What all should be done to a Pontiac Montana when fixing a head gasket leak?, how to remove a kia 2 7 bakkie 2007 model air manifold gasket, how to replace saab 93 turbo head gasket, i changed the head gasket on my 2005 buick rendezvous now motor is shaking, installing 400 pontiac heads, labor time 2002 f150 head gaskets, pontiac 7k3 heads