Skip to content

1998 slk fuel guage empty

You search PDF repair manual about 1998 slk fuel guage empty, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998-1999 Chevrolet and GMC S/T Pickup and 2 Door Utility Incorrect Fuel Gauge Readings

download
Condition Some owners may comment on incorrect fuel gauge readings. The fuel gauge may read empty (E) with approximately 1/3 of a tank of fuel remaining, or the fuel gauge rarely reaches the full (F) mark when the fuel tank is filled. Correction Reprogram the vehicle control module (VCM) with the revised Fuel System Calibration. Use the appropriate calibration listed below. Refer to the latest Techline information for programming procedures. Calibration Information Important: These calibrations are not available from GMSPO. These calibrations are available Subject: Incorrect Fuel Gauge Readings (Reprogram Vehicle Control Module with Revised Calibration) Models: 1998*-99 Chevrolet and GMC S/T Pickup and 2 Door Utility Models 1998*-99 Isuzu Hombre with 4.3L Engine (VINs W, X – RPOs L35, LF6) *RPO ZN4 Only Plant Division VIN Breakpoint Linden Chevrolet (Blazer) XK162355 Linden GMC (Pickup) XK508493 Linden GMC (Jimmy) XK508505 Shreveport Chevrolet X8140835 Shreveport GMC X8512385 Shreveport Isuzu (RPO ZN4 W8668201-W8670669 Shreveport Isuzu X8650007-X8650733 Calibration P/N (New) Application 09374032 (Fuel System Calibration) S/T 100 (Pickup) &LF6/L35 09374033 (Fuel System Calibration)

1998-2000 HONDA Accord L4 Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A M/T WITH CRUISE CONTROL 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. Zoom Sized for Print 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. Zoom Sized for Print 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. . Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. Zoom Sized for Print 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A

1998 Chevrolet Chevy K Pickup DTC P1626 Theft Deterrent Fuel Enable Signal Not Received Repair Manual

download
An intermittent may be caused by any of the following conditions: Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems. Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This test checks if communication can be established between the scan tool and the VTD. If the scan tool cannot communicate with the VTD, refer to Diagnostic System Check – Theft Deterrent in Theft Deterrent. 3. This test checks for any opens in the serial data circuit between the VCM and the VTD. This also checks for any intermittent malfunctions associated with the serial data circuit. 4. This step is to determine if the condition that set the DTC is still present. The engine must be cranked in order to set this DTC. If the condition is present, the engine will start and then stall, indicating the VCM is disabling fuel. 7. Use a scan tool to clear and check for any DTCs in all the modules connected to the Class 2 Serial Data circuit (VCM, VTD, ATC, and BCM). the module itself. After repairing the cause of DTC P1626, clear all DTCs from the systems capable of storing this DTC and DTC U1192. 1 Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module’s data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the scan tool. 2. Turn ON the ignition leaving the engine OFF. 3. Attempt to establish communications with the VTD (Passlock) Control Module. Does the scan tool communicate with the VTD (Passlock) Control Module? — Go to Step 3 Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent 3 Check the Class 2 Serial Data circuit for the following intermittent conditions: Did you find a problem? • An open in the Class 2 Serial Data circuit between the VCM and the VTD (Passlock) Control Module. • A short to ground. • A short to voltage. • Loose or damaged terminals at the DLC, VCM or the VTD (Passlock) Control Module. — Go to Step 6 Go to Step 4 4 1. Turn OFF the ignition. 2. Connect or install any connectors or components that were disconnected or removed. 3. Clear all DTCs using a scan tool. 4. Turn OFF the ignition for 15 seconds. 5. Attempt to start the engine. Does DTC P1626 reset? — Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent Go to Step 5 5 This DTC is intermittent. Are any additional DTCs stored? — Go to the applicable DTC table Go to Diagnostic Aids 6 Repair the circuit as necessary. Refer to Wiring Repairs or Connector Repairs in Wiring Systems. Is the action complete?

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

1984-1998 Jeep Wagoneer/ Commando/ Cherokee Emission Controls Crankcase Ventilation System (PCV/CCV)

download
CCV Fitting See Figures 2 and 3 1. With the engine running, remove the CCV fitting. a. If the fitting is not plugged, a hissing noise will be heard as air passes through the valve. A strong vacuum should also be felt when a finger is placed over the fitting. b. Install the CCV fitting. c. Remove the fresh air hose from the air cleaner assembly and loosely hold a piece of paper over the open end of the hose. After allowing about one minute for the crankcase pressure to reduce, the paper should be sucked against the opening with a noticeable amount of force. 2. Turn the engine OFF . Remove the metered orifice fitting, and check for a plugged condition. A clicking noise should be heard to indicate that the valve mechanism is free. 3. If the crankcase ventilation system meets the tests in Steps 1 and 2 above, no further service is required. If not, the CCV fitting must be cleaned and the system checked again. 4. If Step 1c fails when the CCV fitting is cleaned, it will be necessary to replace the molded vacuum hose with a new one, and to clean the metered orifice port. 5. Clean or replace the engine air cleaner filter element with a new one-for more details, refer to the air cleaner procedure located in General Information & Maintenance. Fig. 2: CCV system diagram for 4.0L engine Fig. 3: CCV system diagram for the 2.5L engine Evaporative Emission Control System OPERATION The evaporative emission control system prevents the release of unburned hydrocarbons, from gasoline or gasoline vapor, into the atmosphere. When pressure in the fuel tank is below 3 psi (20 kPa), the pressure relief/rollover valves open allowing fuel vapors to flow to the evaporative canister where they are absorbed by a charcoal mixture. This prevents excessive pressure buildup in the fuel system. Most canisters are equipped with a calibrated orifice at the inlet to the canister.