1998 subaru forester repair manuals pdf

You search PDF repair manual about 1998 subaru forester repair manuals pdf, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1998 subaru forester repair manuals pdf Direct Download speed 5432 Kb/s

  1998 subaru forester repair manuals pdf Full Version speed 8172 Kb/s



1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 2006 ford focus ses repair manual, cft30 scan codes, 1999 chevy S10 - manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, 1999 cavalier A/C instructions, 1998 ford escort auto repair manual free, mpv 2002 p0140, 1999 tahoe repair manual

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, Replacing the reverse band Dodge 1500, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, repair manual for 1998 chevrolet 1500, downloadable schematic for 99 Chevy suburban evap system, ax12-1500 nut torque, 2010 silverado 1500 4 3 liter canister vavle solenoid, how to replace actuator on 2005 chevy 1500, lifter repair on 02 avalanche

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

0

Filed Under (Honda Manuals) by admin on 17-02-2012

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly

Related Content:

02 saturn sl2 no start, free 1996 Honda accord lx repair manual, Free Transmission Manuals Downloads, honda civic 2007 cvt transmision sensors detail pdf, honda civic 2009 repair manual pdf, honda civic shudder ac, Honda Fit Clutch Replacement, how to use a compressor clutch tool honda civic, ISUZU AXIOM P0346, repair manual for 1996 nissan pickup

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-07-2012

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

Related Content:

Sienna Sliding Door Cable Replacement, 1998 sienna repair manual, how to fix g-6 door latch, how to remove a chevy tahoe bump stop, lexus door adjustment wind, toyota sienna sliding door repair manual

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 560sl repair 1988, 2000 buick century service manual free, 2000 saturn sl1 owners manual, Diagram of us system old mobile intrigue, 2000 buick lesabre service manual pdf, 2000 buick lesabre repair manual free pdf download, 2000 nissan altima po340, 2000 Buick Regal Repair Manual

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, what is the tcc solenoid on a 2 2 cavalier, Powertrain Generator 6500 Parts Diagram, bully side ste for jeep instructions, no powertrain dtc\s or freeze frame data, p1860 tcc pwm solenoid circuit electrical, powertrain generator 6500 owners manual, powertrain generator parts, powertrain generator ptg1000, replace radiator 2000 dodge durango

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette, 2002 silverado remove front driveshaft, 2003 mitsubishi eclipse replace evapulator, how to remove malibu 2008 instrument gauge cluster cover, Redezvous Dash Removal, how to remove the heater core on 2000 VW Beetle, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, 2004 Buick lesabre inrument cluster removeal

1998-2000 HONDA Accord L4 Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line

0

Filed Under (Honda Manuals) by admin on 16-07-2012

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A M/T WITH CRUISE CONTROL 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. Zoom Sized for Print 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. Zoom Sized for Print 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. . Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. Zoom Sized for Print 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A

Related Content:

1993 Corvette Service Manual PDF, vent line 1998 mercy sable, ford taurus 2001 engine vacuum hoses on intake, What color is the tcc solenoid in toyota sequoia, VACUUM LINES ON A 2003 GM 6 CLINDER, vacume lines on 2004 pt cruiser gt, 2002 2 4L olds alero vacuum hose routing diagram, location of shift solenoids on 2004 buick rendezvous, 3 9 dodge engine vacuum schematics 1988, hose assemble for air condition on toyota tundra 2000

1998-1999 Chevrolet and GMC S/T Pickup and 2 Door Utility Incorrect Fuel Gauge Readings

0

Filed Under (Chevrolet Manuals) by admin on 28-05-2011

download
Condition Some owners may comment on incorrect fuel gauge readings. The fuel gauge may read empty (E) with approximately 1/3 of a tank of fuel remaining, or the fuel gauge rarely reaches the full (F) mark when the fuel tank is filled. Correction Reprogram the vehicle control module (VCM) with the revised Fuel System Calibration. Use the appropriate calibration listed below. Refer to the latest Techline information for programming procedures. Calibration Information Important: These calibrations are not available from GMSPO. These calibrations are available Subject: Incorrect Fuel Gauge Readings (Reprogram Vehicle Control Module with Revised Calibration) Models: 1998*-99 Chevrolet and GMC S/T Pickup and 2 Door Utility Models 1998*-99 Isuzu Hombre with 4.3L Engine (VINs W, X – RPOs L35, LF6) *RPO ZN4 Only Plant Division VIN Breakpoint Linden Chevrolet (Blazer) XK162355 Linden GMC (Pickup) XK508493 Linden GMC (Jimmy) XK508505 Shreveport Chevrolet X8140835 Shreveport GMC X8512385 Shreveport Isuzu (RPO ZN4 W8668201-W8670669 Shreveport Isuzu X8650007-X8650733 Calibration P/N (New) Application 09374032 (Fuel System Calibration) S/T 100 (Pickup) &LF6/L35 09374033 (Fuel System Calibration)

Related Content:

2011 gmc sierra location of tps, 1998 chevy sierra gmc manual, 1hdfte nozzle repair, Isuzu 1997 wiring diagram between coil and distributor

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual