dodge caravan repair cam seal leak

You search PDF repair manual about dodge caravan repair cam seal leak, if there are search results will appear below. If search results do not exist, please search by others keyword.



  dodge caravan repair cam seal leak Direct Download speed 5432 Kb/s

  dodge caravan repair cam seal leak Full Version speed 8172 Kb/s



LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

0

Filed Under (More Manuals) by admin on 15-06-2012

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Related Content:

2004 ford explorer manual download, Lincoln pa66-gf30 w584a, 2003 ford explorer rear differential removal, removing stuck halfshaft 03 explorer, Free Mercury Mountaineer Repair Manual, free 2002 lincoln ls chilton manual, Ford Five Hundred Repair Manual, 2006 mountainee repair manual, 2006 Ford explorer manual online, 2006 ford explorer manual download

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, Replacing the reverse band Dodge 1500, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, repair manual for 1998 chevrolet 1500, downloadable schematic for 99 Chevy suburban evap system, ax12-1500 nut torque, 2010 silverado 1500 4 3 liter canister vavle solenoid, how to replace actuator on 2005 chevy 1500, lifter repair on 02 avalanche

Troubleshooting and Resolving Water Leaks for FUNSPORT Sunroofs

0

Filed Under (More Manuals) by admin on 13-03-2012

download
1. Opening the sunroof, just after it rains. Standing water on the glass will usually result in water dripping into the cabin. This is not a sunroof fault. Prevention is the solution! Simply drive a short distance to allow any standing water to blow off the glass prior to opening the sunroof. 2. Only after a car wash. High pressure water sprayed directly at the seal will often deflect the seal enough to enter the cabin. This is not a sunroof fault. Prevention is the solution! Don’t spray high pressure water directly on the seal. 3. During a rainstorm, water is immediately visible dripping on the rubber seal under the glass. There may be a problem with glass to seal contact. Carefully examine the seal. If it is visibly damaged or worn, it may need replacement. If dirty, it needs cleaning. An adjustment may solve the problem. Always water test to verify (see sprinkle test procedure below). a. Often dirt or debris will prevent proper contact between the glass and seal. Clean both the glass and seal with plain water (a damp cloth), or if very dirty, a mild detergent solution. Repeat water test after cleaning. If water intrusion between glass and seal continues, adjust the glass hardware. b. Adjust the glass hardware to increase clamping pressure on the seal. See procedure below. Repeat water test after adjusting. If water intrusion between glass and seal continues, replace seal. 4. Water is visible dripping through the glass hardware: Water test to verify (soak and sprinkle). You may need to slightly shift the glass hardware or change the rubber gaskets under the rectangular mounting plates. 5. After a long soaking rain the headliner gets wet. This is likely the result of water coming under the main frame or under the seal. Only a soak test will prove this. a. Under the main frame: remove the screw cover strip or pull back the headliner (of wrapped) and examine the clamping screws. Water spots or rusty screws are an indication that water is coming under the main frame. Remove the clamp frame and water spots or rust will likely be visible on the inside of the roofskin. This can be the result of an over-cut hole, a sunroof not centered on the hole (left a gap) or inadequate sealant. Solution: Remove the sunroof and re-install with new sealant. If the hole was over-cut, a larger size may be required. b. Underneath the main seal: carefully examine and verify proper seal insertion around perimeter of sunroof frame. Bottom of seal should be adhered to main frame with butyl tape. Top outer lip should be mechanically inserted into groove in frame. You may be able to manipulate the seal slightly to correct the problem. Otherwise replace the seal. c. Frame joint: typically will see water spots or rust on hinge block and handle mounting screws, particularly on the right hand side. Remove the knock-in bead and examine the channel for water or water spots. Solution: pull back the main seal at the passenger side and apply a small amount of silicone sealant across the frame joint. Allow to dry before reinserting the main seal.

Related Content:

1997 lumina 3 1l thermostat adjustment dial?, seal for slip on muflers, how to seal compresion hose leak on 2000 bmw 528i, rear main seal leak 2006 suburban, rear seal replacement on 2003 Chevy Cavalier, reinstall 1929 ford rear glass replacement, removing axles 1998 ford expedition, Replacing rear main seal 2003 suburban, ridgeline rear main seal tsb, to change seal on 2003 camshaft sensor

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, 2003 trailblazer torque converter removal, gm 4l60e band adjustment screws, automatic transmission adjustments for 1997 yuko, 2011 crv engine whine, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 1997 e450 power stroke trans mount parking brake, 4r70w transmission rebuild manual download, how to adjust the bands of an automatic trasmission of hyundai accent 2002

Ford V8 Engines Performer RPM Hydraulic Roller Camshaft INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 01-01-2012

download
Disconnect the battery. 2. Drain radiator coolant. Drain plug will normally be located on lower right or left side of the radiator facing the engine. 3. Remove radiator and air conditioning condenser if so equipped. In some cases, the front grill may have to be removed. Measure distance from front cover to grill or brackets that may interfere with camshaft against the length of the camshaft. 4. Remove the gas cap to relieve pressure. Disconnect fuel line and plug. Replace gas cap. 5. Disconnect all linkage from carburetor such as throttle, throttle springs, transmission, cruise control and automatic choke. 6. Tag and remove coil wires and sensor wires. 7. Tag and remove vacuum lines. 8. Remove valve covers. 9. Remove distributor cap and wires, rotate engine until rotor points towards number 1 terminal in cap and pointer on front cover is on top dead center (TDC) and remove distributor. (see Fig. 1) Note: Mark the approximate position of the distributor housing in relation to the manifold to assist in getting the distributor properly located during re-installation. 10. Remove carburetor and intake manifold. Remove and discard intake manifold gasket. 11. Remove rocker arms and pushrods. CAUTION: If your engine has non-adjustable rocker arms (1969-1/2 or later), you must install screw-in studs and high performance •VALVE SPRINGS CAUTION: WARNINGS ABOUT YOUR WARRANTY In order for this Performer RPM roller cam to be covered under ANY WARRANTY, you MUST use the correct Valve Springs. Failure to install the correct valve springs may cause lifters not to follow the cam lobes and damage engine parts. This camshaft is designed to function with valve springs that have a closed pressure of 110 lbs, open pressure of 320 lbs and a lift of .575″. Special H.P. retainers may be necessary with your installation for proper spring height. Do not use rotator type valve springs or retainers for this application. Note: Edelbrock Sure Seat Valve Springs #5762 are not recommended.  IMPORTANT NOTES AFFECTING YOUR WARRANTY CAM LOBE DAMAGE – Cam lobe wear is almost non-existent unless mismatched parts are used or installation of the cam and lifters is done improperly. Cam damage can result from the timing gear loosening due to improper torque on bolts. Bolts holding gear to camshaft should be torqued carefully and a locking compound applied to threads of bolts. Before installing your new Performer-RPM roller camshaft, check the gear drive on the distributor and oil pump for any signs of wear. If worn, be sure to replace with a new gear or you may wear out your camshaft prematurely. High-pressure oil pumps are not recommended with Performer RPM roller camshafts. Edelbrock camshafts are designed to use with Edelbrock timing chains.  CAM GEARS AND CAMSHAFT END PLAY- If cam gear becomes loose, the cam will slide back in the block, causing the lifters to hit the lobes next to them and also the cam bearing journals. If the engine is run after this happens, the bottom of the lifters and the sides of the lobes will become damaged. See Installation Instructions section for end play specifications.  LIFTERS Edelbrock offers a retrofit roller lifter kit for engines not originally equipped with roller lifters. Use part #97453. To install your roller lifters, use fresh clean oil on the lifter and the lifter bore just prior to installing. The guide bar (high side of tappet) must face the opposite side of block. See roller lifter instructions for additional information. ( Note: 289-302 engines require removal of the cylinder heads to provide enough clearance to install roller lifters, which are taller than standard hydraulic lifters.)  PUSHRODS AND ROCKER ARMS High performance pushrods, roller rocker arms and rocker studs are recommended for this installation. After the cam is installed and timed correctly (see Figure 2), it will be necessary to check each pushrod for correct lifter preload. INSTALLATION INSTRUCTIONS 1. Check lifters as covered in Lifters section. Coat cam lobes with fresh clean oil. Lube distributor drive of cam with assembly lube (supplied). 2. Install new camshaft. Re-install thrust plate with new sprockets and timing chain with timing marks lined up as recommended by factory specifications (See Figure 2). Reinstall the fuel pump eccentric before installing sprocket bolt and washer

Related Content:

roller lifters trouble 2010 gmc, 2006 DT466 lifters, torque side trrminal battery, sun distributer machines parts, rear cam bolt torque 4 0 sohc, mitsubishi 4g13 series wiring diagram manual, ford 302 camshaft endplay, Ford 2003 4 liter V6 camshaaft bolt torque, 5 3 camshaft problems, v6 3000 four cam 24 vvt-i thermostat location

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 2006 ford focus ses repair manual, 1999 chevy S10 - manual, cft30 scan codes, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, 1999 cavalier A/C instructions, 95 ford ranger owners mqnual, pdf 97 ford ranger, 1998 ford escort auto repair manual free

2000-2006 Toyota Tundra ADVANCED FOLDING COVER INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 01-03-2012

download
Install Rails And Seals 1. There are two rails. Put the rail with the 3rd leg hinge clamp, (Fig.1) with screw facing tailgate, closest to the cab on the bed rail. Make sure the rail is as close as possible to the cab . Remove the two-sided piece of tape and push the rail down. Then, do the same for the other side. ail D seal at end of Tailgate Box Seal It is very important, to have the rail touching the front of the truck box, so the cover can line up correctly. If unable to exactly begin at the front of box, make sure each rail is equal distance away from the front of the box on each side. Check this first, if the cover does not line up correctly. . Next, remove the 10 clamps from your installation kit. To clamp the rail on the truck bed use a 5/16″ socket, wrench or drill then tighten the screws on clamps. Be careful not to over tighten! You must use the one preset spot on each rail (Fig.2). Then space out evenly The first step in installing the Box Seal is to place the guide on the outside of the rail by the cab (Fig 3).Then, remove about 8 inches of the two-sided tape from the Box Seal. Place the Box Seal on the outside of the guide. Start from about an inch from the front and gradually pull the white paper back; push the Box Seal against the guide and rail all the way down the rail, which will give you a perfectly straight seal. Run the seal just past the stake pocket hole and stop, the remaining seal will be trimmed later. Do this on both sides. Finally, remove the white paper on the D-Seal and place it at the end of the rail by the Tailgate (Fig. 4) 1. Place the 3rdleg hinge on the cover, which drops in the key hole bracket (mounted on cover), into the 3rd leg hinge clamp on the rail. The yellow warning sticker on the cover will be facing up. (Fig.5) 2. Step back behind the tailgate and center the cover. Do not center cover to the Box Seal, center the cover to the Truck Bed. 3. Tighten down the screws in both 3rdleg hinge clamps with a 5/16″ socket , wrench or drill. (Fig.6) 4. Undo the four tie downs and unfold the cover over the truck bed. (Fig. 7) For detailed instructions see the yellow sticker under the cover. 5. Tighten the lock nuts on all clamps and both 3rd hinge leg clamps. Use a 3/8″ wrench. (Fig.8)

1994 Ford Explorer SPINDLE AND SHAFT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 01-02-2012

download
Removal 1. Raise and support vehicle. Remove wheel assembly. Remove caliper from rotor. Remove locking hub. See AUTOMATIC LOCKING HUBS or MANUAL LOCKING HUBS under REMOVAL & INSTALLATION. 2. Remove wheel bearings, lock nuts, hub and rotor. Remove spindle-to-steering knuckle nuts. Tap spindle with plastic hammer to free spindle from steering knuckle. See Fig. 9 . Remove spindle, spindle seat (if equipped) and splash shield. 3. On right side applications, remove and discard keystone clamp from shaft assembly and stub shaft. Slide rubber boot onto stub shaft. Remove shaft assembly from right axle. See Fig. 9 . 4. Remove left shaft assembly (if required). On all applications, wrap spindle in protective cloth and place second step of spindle in soft-jawed vise. 5. On Explorer and Ranger, remove oil seal using slide hammer and Seal Remover (TOOL-1175-AC). Remove needle bearing from spindle. Press seal from shaft assembly. See Fig. 9 . 6. On Bronco and F150, remove needle bearing and oil seal using slide hammer and Cup Puller (T77F- 1102-A). Press seal from shaft assembly. Installation 1. Clean all dirt and grease from spindle bearing bore. Ensure bearing bore is free of nicks and burrs. On Explorer and Ranger, install seal on shaft assembly using press and Seal Installer (T83T-3132-A). 2. On Bronco and F150, install seal on shaft assembly, with seal lip toward spindle. On right side applications, install rubber boot and NEW keystone clamps on stub shaft. Install right shaft assembly into stub shaft, with stub shaft missing spline aligned with shaft assembly. 3. Ensure splines are fully engaged. Install rubber boot over assembly and tighten keystone clamps. On left axle applications, install shaft assembly through steering knuckle, and engage in splines. 4. Install needle bearing in spindle, with manufacturer identification mark facing away from spindle bore. For bearing installation, use Handle (T80T-4000-W), and Bearing/Seal Installer (T83T-3123-A for Explorer and Ranger; T80T-4000-S for Bronco and F150).

Related Content:

2005 f150 half wrap, how to replace a turbine speed sensor on a 1998 ford explorer, remove shaft 326rx service manual, spindle nut torque 2007 ford 150

1985 -1995 5.0L Ford V8s with Hydraulic Roller Lifter Cams ACCU-DRIVE CAM GEAR DRIVE SYSTEM Installation Manual

0

Filed Under (Ford Manuals) by admin on 03-01-2012

download
1. Remove stock timing cover. Rotate engine to Top Dead Center of cylinder #1 so that the timing marks on the original crank and cam sprockets are directly lined up with each other, i.e. the mark on the crank sprocket will be straight up and the mark on the cam sprocket will be straight down. Using suitable gear puller, remove stock crank and camshaft sprockets and timing chain. Refer to repair manual if necessary for individual steps. 2. Assemble Accu-Drive as shown in Figure 1. 3. Install crank gear with the large inside chamfer toward rear of engine and timing mark toward front of engine. Make certain crankshaft drive key is aligned with keyway of the crank gear before assembling. 4. See Figure 2 “Camshaft Gear Assembly”for correct assembly. (a) Place well-lubricated thrust washer on the rear (block) side of cam gear. (b) The Edelbrock Accu-Drive system is furnished with an 0.032″ thick thrust ring that installs between the back side of the cam gear and the front side of the camshaft thrust plate. Torque the thrust plate retaining capscrews to 9-12 ft./lbs. NOTE: No thrust button is used on Ford engines. (c) Select the desired keyway in the crank gear “0″ (standard), “A” (4ºadvanced at the crank, 2º at the cam), or “R” Place a small amount of clay on the front end of both axles as shown in Figure 3. NOTE: It will be necessary to cut material off rib inside front cover to hold idler gears in place. (b) Install front cover with gasket in place. (c) Remove cover and measure the thickness of the compressed clay. It should be .005″-.030″. Do not tighten cover down until proper clearance has been obtained. Without sufficient clearance, there is risk of cracking the cover when tightened down. (d) If clearance is less than .005, you will need to grind off idler axle as shown to obtain proper clearance. If clearance is greater than .090, replace left side (larger idler side) stud with tapered end axle provided in the kit. Re-install idler assembly and recheck for minimum clearance between block and front cover. 8. With all gears correctly in mesh and timed, tighten the camshaft capscrew to 35 ft./lbs. It would also be a good idea to use Locktite™ or equivalent on the bolt threads prior to final assembly. 9. Lubricate all gears and bearings with engine oil. 10. Re-install the front cover. 11. Re-install all components removed in preparation for step 1

Related Content:

P30 bellcrank assy, 1989 ford escort 1 3 thrust washer end play, 1995 ford 6 cylinder cam gear marks, ford 200 camshaft

Hemi Chrysler 300C, Dodge Magnum and Dodge Charger Installation instructions

0

Filed Under (More Manuals) by admin on 06-12-2011

download
Installation instructions: 1. Raise and support vehicle. 2. Lubricate factory rubber hangers with penetrating oil. 3. Remove fasteners attaching driver side tailpipe/resonator assembly to rear of center-mount factory muffler. Remove tailpipe/resonator from factory hangers and from vehicle. 4. Loosen stock clamps attaching stock exhaust to converter pipe outlets near front of vehicle. 5. Remove black factory stiffener cross-brace from bottom of vehicle. 6. With a helper, remove factory hanger rods from rubber hangers and remove remaining exhaust system from vehicle. 7. Place two supplied clamps over inlets of X-pipe and install assembly over outlets of factory converter pipes. The X- pipe should be installed to position the slotted-hole brackets towards the top of the pipes. Do not fully tighten clamps at this time. 8. Using two supplied clamps, install mufflers over outlets of X-pipe assembly. Do not fully tighten clamps at this time. 9. Using two supplied clamps, install left and right tailpipes to outlets of mufflers and insert hanger rods into factory rubber hangers. Do not fully tighten clamps at this time. 10. Install tips with clamps over outlets of tailpipes. 11. Reinstall factory body stiffener brace to bottom of vehicle. 12. Starting at front of vehicle, align system and tighten clamps. You may need to push system upwards while tightening clamps to be sure system adequately clears stiffener brace. 13. Align tips and tighten clamps .

Related Content:

free owners manual for dodge intrepid 2001, 1996 Dodge Intrepid Owners Manual pdf, 1996 dodge ram 1500 owners manual free download, 1999 dodge ram wagon 1500 owner manual, dodge d50 service manual free, 97 caravan repair manual pdf download free, cadillac DTC PO622, Dodge Charger 2 7 Firing Order, 1500 dodge ram wagon 1999 owner manual, install directions for dodge 2500 ac unit

Related Content:

2004 ford explorer manual download, Lincoln pa66-gf30 w584a, 2003 ford explorer rear differential removal, removing stuck halfshaft 03 explorer, Free Mercury Mountaineer Repair Manual, free 2002 lincoln ls chilton manual, Ford Five Hundred Repair Manual, 2006 mountainee repair manual, 2006 Ford explorer manual online, 2006 ford explorer manual download