dodge dakota heater core replacement instructions

You search PDF repair manual about dodge dakota heater core replacement instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  dodge dakota heater core replacement instructions Direct Download speed 5432 Kb/s

  dodge dakota heater core replacement instructions Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

2000 Chevrolet Blazer HEATER CORE Removal And Installation Procedure

0

Filed Under (Chevrolet Manuals) by admin on 20-05-2011

download
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE . 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws Courtesy of GENERAL MOTORS CORP. 3. Remove the heater core access cover. 4. Remove the heater core from the heater/vent module. Fig. 15: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the heater core to the heater/vent module Fig. 16: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. 2. Install the heater core access cover. Tighten Tighten the heater core access cover screws to 1.9 N.m (17 lb in). NOTE: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre

2001-2007 Toyota Highlander MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 27-03-2012

download
This bracket kit fits the 2001-10 Toyota Highlander. For the ’01-’07 Toyota Highlander, follow the instructions below. For ’08-’10 Toyota Highlander instructions, see the separate section included in these instructions. Important: please use all supplied bolts and parts and read all instructions carefully before beginning this installation. The majority of questions you may have can be answered within the text, and proper installation will ensure safe and secure travel. Now, begin the installation. Fig.C Fig.D Fig.E 1. Start by removing four plastic fasteners that attach the grille to the core support (Fig.C). 2. Once all the fasteners are removed, squeeze and push out a square plastic clip fastener for the grille, located between the headlight housing and the radiator support frame on each side. 3. Pull back the grille and remove the Phillips screw that attaches the fascia to the hood latch support (Fig.D). 4. On each side, remove three plastic fasteners: two of the plastic fasteners are attaching the fender liner to the fascia (Fig.E); the other plastic fastener is attaching the fender liner to the frame rail (Fig.F) 5. Remove ten 10mm (head) bolts (Fig.G) and two plastic fasteners (Fig.H) attaching the lower splash shield to the fascia and the sub frame. 6. On both sides, pull back the fender liner and remove one 10mm screw attaching the corner of the fascia to the fender (Fig.I). Fig.K Plastic fastener MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 1-800-669-9690 fax 360-735-9300 KIT# 1180-1 05/14/10 KS 9. Remove the foam shock absorption core by pulling forward (Fig. L). Note: this will not be reinstalled. Retain the foam shock absorption core and attachment hardware so that it can be replaced if the bracket is ever removed. 10. Remove six 14mm (head) bolts to remove the bumper core (Fig.M). Note: this will not be reinstalled. Retain the bumper core and attachment hardware so that it can be replaced if the bracket is ever removed. 11. Remove the alignment studs at the end of each frame rail (Fig.N). 12. Now, place the main receiver brace into the ends of the frame rails (Fig.O). 13. Bolt the main receiver brace into place using the three supplied 10mm x 1.25 x 35mm bolts, flat washers and lock washers (Fig.P). Repeat for the other side. Tighten to the torque specifications listed at the end of these instructions.

Related Content:

how to remove the radiator grill on a 2002 toyota highlander, yhs-synd1, banjo meter model MFM220, plastic bezel 1203 manual, TH350 set end play, remove 2007 toyota highlander grille clips youtube, plastic bezel 1312 watch alarm setting, medline mattress manuals online, instructions for removing altenator 2001 honda civic, gen590 watch

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, zimmatic pivot wiring, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, free 1997 buick regal gs wiring diagrams, Service manual dodge durano 2002 pdf, 2000 Buick LeSabre Wiring Diagram

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to change evaporator core on 1998 blazer, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, Ford Expedition heater core instructions, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

1994 Ford Mustang A/ C Evaporator Housing Removal and Installation

0

Filed Under (Ford Manuals) by admin on 03-06-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01 . If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side) . 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment.

Related Content:

acadia remove center console panel, remove center console 2002 pontiac grand prix, how to remove center console 2001 ford escort, howtoremovecenterconsolefrom2007malibu, how to tighten the overhead console laredo, 2000 corolla shift knob, how to take a part 2007 toyota tundra center console, how to replace center console lid on toyota tundra, HOW TO REMOVE THE CENTER CONSOL COVER ON A 2011 HONDA ACCORD, remove 2005 rav4 console

2000 Ford Crown Victoria/Grand Marquis Evaporator Core Housing Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 03-07-2012

download
Evaporator Core Housing Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Recover the refrigerant. For additional information, refer to Section 412-00 . 3. Drain the radiator so that the coolant level is below the heater core. For additional information, refer to Section 303-03 . 4. Raise the vehicle. For additional information, refer to Section 100-02 . 5. Remove the RH front wheel and tire. 6. Remove the screws from the RH fender apron and remove the fender apron. 7. Remove the nuts. 8. Lower the vehicle. 9. Remove the blower motor switch resistor. For additional information, refer to Section 412-04 . 10. Disconnect the connector. 11. Disconnect the evaporator to compressor suction line from the suction accumulator drier. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 12. Disconnect the condenser to evaporator tube from the A/C evaporator core inlet tube. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 13. Remove the nuts and position the purge valve and backet away from the evaporator core housing. 14. Remove the heater hoses from the heater core. 15. Disengage the connectors fom the bracket. 16. Disconnect the connector. 17. Remove the nut and reposition the wire harness away from the evaporator housing. 8 18. Disengage the harness from the bracket. 19. Remove the pin-type retainer and clip and remove the instrument panel lower insulator. 20. Fold back the carpet and remove the screw. 21. Inside the vehicle, remove the screw. 22. Remove the nuts(engine side).

HONDA Front Seat Belt Replacement Warranty Policy

0

Filed Under (Honda Manuals) by admin on 24-11-2011

download
CUSTOMER INFORMATION : The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your car. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your car, or that your car has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. ? 1996 American Honda Motor Co., Inc. – All Rights Reserved . ATB 14788-17665 (9601) 1 of 2 JAN 22, 1996 92-012 BODY ALL 1986 and later Applicable To Model File U nder Issu e D ate Bulletin N o. Service Bulletin Front Seat Belt Replacement Warranty Policy (Supersedes 92-012, dated March 13, 1992) Warranty policy for front seat belt replacement is to replace either the belt/retractor mechanism or the buckle when either does not work properly. Warranty covers the replacement of the failed half of a belt, not the entire assembly (see PARTS INFORMATION ). NOTE: For 1970 through 1985 models, seat belts are replaced as a complete assembly under a separate warranty policy. COMPONENT REPLACEMENT Front seat belts are made by several suppliers, and some are sold as individual components (two separate halves); they are not stocked as a complete set. Therefore, whenever you replace a belt, make sure the new belt half is the same type and from the same manufacturer as the original – otherwise, the belt may not buckle properly. To determine the manufacturer and type (or “model”) of the belt, look for the white tag on the original belt in the car. The tag is on the retractor side of the belt (visible at the lower attachment point), or on the belt if you pull the belt all the way out. From the tag, mark down the manufacturer’s name (either Nippon Seiko K.K. or Takata), the belt “model” number and the date of manufacture. If the tag is missing or illegible, look on the buckle component for the name Nippon Seiko K.K. or the stylized “T” mark () for Takata. NOTE: Some belts may have NSK Warner K.K. as the manufacturer’s name. Use Nippon Seiko K.K. belts as the replacement. Take the information to your Parts Department to order the proper replacement belt. NOTE: For more information on seat belts and seat belt related items read: -Twisted Seat Belt (ServiceNews, July ’85) -Seat Belt Testing and Repair (Service Bulletin 86-014, August ’86) -Automatic Seat Belt Troubleshooting (ServiceNews, May ’89) -Lap Belt Retracts Slowly (Service Bulletins 90-003, January ’90 and 90-012, April ’90) -Torn Seal on Seat Belt Track (Service Bulletin 91-004, March ’91) -Slow to Retract Seat Belt, Cleaning the Guide Ring (ServiceNews, April ’91) -Accord Shoulder Belt System Wire Colors (ServiceNews, May ’91) -Seat Belt Slow to Retract (Service Bulletin 91-030, December ’91) Refer to your Service Bulletin Index and the ServiceNews Index for model specific information. Most repairs do not require seat belt component replacement. PARTS INFORMATION For front seat belt replacement ordering information and availability, contact your parts center.

Related Content:

1986 chevy c10 new belt, installing new rotors on a 1992 ford f250 4wheel drive, volvo 850 repair seat belt tensioner manual download, 2004 chevy malubu surpupten belt replacement on a 2 2 liter on you tube, 2002 chevy malibu passlock gm bulletin, sun visor repairs 2013 honda accord, snugtop glass button bolt, replace sun visor 09 honda accors, repairing seat belt in dodge dakota, 1990 HONDA CIVIC SEATBELT FUSE BLOCK

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

0

Filed Under (More Manuals) by admin on 05-05-2012

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, How to replace shift indicator on 99 f150, replace shifting cable for 2003 GMC Envoy how do you remove the console, replace shifter handle on 2000 malibu, replace shifter cable 2003 rendezvous, cover push button on shifter for chevey 2007 cobalt automatic, buick rendezvous detached shifter, buick rendezvous gear shift cable repair, chevy cobalt shift lock

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram