1999 ford contour service manual

You search PDF repair manual about 1999 ford contour service manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1999 ford contour service manual Direct Download speed 5432 Kb/s

  1999 ford contour service manual Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, how to replace 2003 impala power steering pump, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle

ALL INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 23-04-2012

download
SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. Groan noise during stopping: • Usually caused by glazing of the rotor’s surface as a result of heavy or frequent braking. • Refer to technical bulletins specific to the model of vehicle regarding this issue. • Replace the brake pads, then resurface the rotors and finish them with sand paper. Refer to Brake Service on page 5 for additional detail. Single clunk noise from front suspension when applying the brakes: • The noise is a result of the brake pads shifting in the direction of rotor rotation when the brakes are applied. Can be duplicated by lightly touching the brake pedal. • • If the brake pedal is pushed hard, the noise is less likely to occur. Make sure the brake pads and pad hardware (shims, springs, clips, etc) are installed correctly. Refer to ASIST for vehicle specific brake service information. Refer to Brake Service on page 5 for additional detail. Mull e he engine is started: • st er models, the self check occurs the first aches 5 mph after the engine is started. ors or drums. • WARNING: Brake dust may be hazardous if inhaled. Refer to the Service Manual (ESM) for brake • n and lubrication of brake pads, CAUTION: Do not get grease on the brake pad friction surface. A • Brake Judder is caused by rotor thickness variation and/or rotor run out.

Related Content:

lexus engine 2gr-fe chirping squeak noise sb0010-09, titan 5500 generator manual, Free 98 Honda Accord service Repair Manual, manual for 1993 bmw 325i, 2012 f-150 service manual, Honda Accord 1998-2002 Service Repair Manual free PDF, motorcraftservice com, 94 nissan pickup diagnose repair, Motorcraft Service Manual Download, Free Mercruiser 3 0 Service Manual

Acura MDX Torque Converter Shudder or Vibration Between 35 and 40 MPH Repair Manual

0

Filed Under (Acura Manuals) by admin on 24-11-2011

download
1. To confirm the client’s complaint, test-drive the vehicle on a smooth road, preferably with a slight incline. Set the cruise control between 35 and 40 mph, and monitor the engine rpm using the vehicle’s tachometer, or use the HDS to take a snapshot of the engine rpm. 2. If the engine speed fluctuates several hundred rpm while maintaining a constant vehicle speed, disconnect the EGR valve and retest the vehicle. •If the fluctuation is gone, refer to the EGR troubleshooting in the service manual. •If the engine rpm still fluctuates, and the transmission does not have any other symptoms (shifting problems, slipping, transmission DTCs) go to step 3. 3. Drain the transmission fluid, then strain it through a paint strainer. •If you find little or no contamination in the strainer, the ATF is OK, even if it smells burnt, is discolored, and/or the magnetic drain plug has small chips, flakes, or metal fuzz on it. Go to REPAIR PROCEDURE A . •If you find large amounts of contamination (pieces of metal or friction material) in the strainer, go to REPAIR PROCEDURE B . REPAIR PROCEDURE A 1. Remove the torque converter: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Install the torque converter: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 3. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 4. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are off. •Start the engine, and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes. REPAIR PROCEDURE B Follow the IN-WARRANTY EXCHANGE steps in service bulletin 90-009, Automatic Transmission In- Warranty Exchange Program , to order a remanufactured A/T, replace the failed A/T, and return the failed A/T core. 1. Remove the transmission: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Clean the transmission cooler. Refer to service bulletin 89-015, ATF Cooler Cleaner . 3. Install a remanufactured transmission: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 4. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 5. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off. •Start the engine and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes

Related Content:

1998 mazda MPV owners manual, 2002 ford thunderbird service manual, freelander engine control module mobility module master, how much for torque converter for 2001 mdx, torque converter problems symptoms for 1999 3 2tl acura, what is a torque shudder

1999 FORD EXPLORER/ RANGER TRANSMISSION-4R44E OR 5R55E-SLIPPING SHIFT/ DELAYED OR NO ENGAGEMENT REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 18-05-2012

download
SERVICE PROCEDURE F87Z-7A100-DB Main Control (4.0L EI Explorer) F87Z-7A100-EB Main Control (4.0L SOHC Explorer) 1. Perform normal diagnosis for this concern. XL2Z-7L491-AA Bracket XL2Z-7G383-AA Electronic Pressure Control (EPC) 2. Perform Line Pressure Tests as listed in the Solenoid 1999 Explorer/Mountaineer, Ranger Workshop Manual. OTHER APPLICABLE ARTICLES: NONE WARRANTY STATUS: Eligible Under The 3. If pressures are low, perform Pinpoint Test for Provisions Of Bumper To the EPC solenoid. Bumper Warranty Coverage And Emissions Warranty 4. Inspect the bracket that attaches the Torque Coverage Converter Clutch (TCC), Shift Solenoid B OPERATION DESCRIPTION TIME (SSB), Shift Solenoid D/Coast Clutch Solenoid 991610A Replace Electronic 1.2 Hrs. (SSD/CCS), and EPC solenoids to the main Pressure Control (EPC) control for damage. If the bracket is damaged, Solenoid And Clean Main replace both the bracket and solenoid. Control (Includes Time For 5. If the bracket is not damaged, inspect the Road Test) – 4R44E Or solenoid for the affected date code (refer to the 5R55E following Manufacturing Date Code Chart) and 991610B For Line Pressure And ID marking (Figure 1, Views 1, 2, and 3). If the Pinpoint Tests, Use “A” solenoid is one of the affected, replace it. Time As Outlined In The Warranty And Policy MANUFACTURING DATE CODE Manual Date Code Month/Year DEALER CODING 868xx August 1998 CONDITION 869xx September 1998 BASIC PART NO. CODE 870xx October 1998 7G383 01 871xx November 1998 OASIS CODES: 501000, 502000, 50300

Related Content:

replacing manual, how replace torque converter clutch solenoid on a 1998 suburban, escort transmission harsh engagement, replace ford explore sports 1999 clutch line, remove r lower control arm 1998 olds 88 what electric impack wrench to usee, 5r55e tcc, 02 expedition tcc solenoid replacement manual, how to remove a epc solenoid from a1998 ford expedition transmission, isuzu trooper fuel solenoid valve location, pictures removing the epc solenoid on a1998 f150

1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia

1999-2001 Infiniti Q45 MIL “ON” REAR O2 SENSOR DTC SERVICE PROCEDURE

0

Filed Under (Infiniti Manuals) by admin on 07-01-2012

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2/4 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 1999-2001 Q45 23710-3H000, -3H001, -3H005, -3H006, -3H007 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Perform ECM Reprogramming on page 3. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. SELF-DIAG RESULTS SYSTEM ENGINE DATE 01/24/2002 5:35:07 P/N 23710-3H000 DTC Code TP020024 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 3/4 ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Related Content:

how to replace ECU on 2005 Cadillac CTS, 2007 ecm location saturn vue, 2008 chevy 3 5 repair manual, infiniti q45 manual torrent, lincoln ecm reprogramming, where is the ecm on 454 engines, Ford 1998 E350 loction of the ecm, ecm update audi 2006 list, ecm relay escort 1997, ecm IS WHERE IN A 2008 IMPALA

Honda Navigation System Information and DVD Information and Inspection Manual

0

Filed Under (Honda Manuals) by admin on 06-07-2012

download
REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system

Related Content:

manual lincoln navigator 2007, reset liftgate lincoln, exploded view 4r55e, service manual for civic 2007, 2005 odyssey service manual free, 2003 honda odyssey service manual, c1998 module calibration failure navigator 2006, invision revolution dvd manual, hubsan x4 manual pdf, lincoln navigator 1998 fuses oxygen

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

0

Filed Under (Ford Manuals) by admin on 15-05-2012

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

Related Content:

0761 emission code ford, repair manuel 91 suburu loyle, manual webasto pdf, manual lever position sensor troubleshooting, free download jo8c parts book, ford ranger transmission repair manual, ford five hundred repair manual 2007 pdf, 86 ford ranger repair manual, 2004 ford ranger owners manual pdf, wiring for a zemmadic 410 pivot

2004-2005 FORD F-150 FRONT BRAKE ROUGHNESS/ SHUDDER WHILE BRAKING REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 10-06-2012

download
ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.

Related Content:

2004 dodge dakota repair manual free download, 2004 Cavalier Repair Manual PDF, change rotors 94 explorer, change rotors on 94 explorer 4x4, copy of 2004 chevy truck mannual, fender passport p 150 service manual, honda pilot 2004 repair manual, how to replace rotors on 2005 f250, MINN ROTOR THICKNESS 04 SEBRING, service manual 2004 chevrolet pdf

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, how to replace 2003 impala power steering pump, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle