gmc yukon universal joint bolt torque

You search PDF repair manual about gmc yukon universal joint bolt torque, if there are search results will appear below. If search results do not exist, please search by others keyword.



  gmc yukon universal joint bolt torque Direct Download speed 5432 Kb/s

  gmc yukon universal joint bolt torque Full Version speed 8172 Kb/s



1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 13-06-2012

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, how to replace rear upper arm kia sedona, torqe for ball joint 2001 prizm, oem ball joint press, peugeot 306 front lower arm removal, lower ball joint press sedona kia, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000

2008 Honda Accord L4-2.4L Knuckle/ Hub Bearing Unit Replacement

0

Filed Under (Honda Manuals) by admin on 19-11-2011

download
Hub Bearing Unit Replacement 1. Raise the rear of the vehicle, and support it with safety stands in the proper locations. 2. Remove the wheel nuts, and the rear wheel. 3. Remove the brake hose mounting bolt (A). 4. Remove the brake caliper bracket mounting bolts (B), then remove the caliper assembly (C) from the knuckle. To prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the caliper assembly from the undercarriage. Do not twist the brake hose excessively. 5. Remove the two washers (A). NOTE: During installation, make sure the washers are installed between the brake caliper bracket and the knuckle. 6. Remove the rear brake disc. 7. Remove the hub bearing unit (A) and O-ring (B). 8. Check the hub bearing unit for damage and cracks. 9. Install the hub bearing unit in the reverse order of removal, and note these items: * Use a new O-ring on reassembly. * After installing the brake caliper, make sure the clearance between lower arm B and the parking brake cable is more than 5 mm (3/16 in.). * Before installing the brake disc, clean the mating surfaces of the hub bearing unit and the brake disc. * Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the wheel. * Check the wheel alignment, and adjust it if necessary. Knuckle Replacement 1. Remove the hub bearing unit. 2. Remove the splash guard (A). 3. Remove the lock pin (A) from the upper arm ball joint, then remove the castle nut (B). NOTE: During installation, install the lock pin as shown after tightening the new nut. 4. Disconnect the upper arm ball joint from the knuckle using the ball joint remover. NOTE: * Be careful not to damage the ball joint boot when installing the remover. * During installation, to connect the ball joint, raise the suspension with a jack. 5. Remove the wheel speed sensor (A) from the knuckle. Do not disconnect the wheel speed sensor connector. 6. Remove the self-locking nut (A) while holding the joint pin (B) with a hex wrench (C), then disconnect the stabilizer link (D) from the knuckle, and remove the brake hose bracket (E). NOTE: Use a new self-locking nut during reassembly. 7. Remove the damper lower mounting bolt (F). NOTE: Use a new mounting bolt during reassembly. 8. Remove the control arm mounting self-locking nut (A) and washer (B). NOTE: Use a new self-locking nut during reassembly 9. Remove the lower arm mounting bolt (A), and the lower arm B mounting bolt (B), then remove the knuckle (C). NOTE: Use new mounting bolts during reassembly. 10. Install the knuckle in the reverse order of removal, and note these items: * First install all the components, and lightly tighten the bolts and nuts, then raise the suspension to load it with the vehicle’s weight before fully tightening to the specified torque values. * Be careful not to damage the ball joint boot when connecting the knuckle. * Before connecting the ball joint, degrease the threaded section and tapered portion of the ball joint pin, the ball joint connecting hole, and the threaded section and mating surface of the castle nut.

Related Content:

2008 F250 STEERING GEAR PITMAN ARM NUT SIZE, bearing retaining nut for a 2004 Trailblazer, brake caliper dust boot honda 2007 accord coupe

2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-12-2011

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

cummins n14 oil pan bolt torque, 2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, n14 connecting rod torque, oil pan bolt torque specs on cummins n-14, 02 ford explorer driveworks front wheel hub torque, torque number sway bar ends 2002 lincoln ls, torque specs for 2002 f250 pitman arm nut, lincoln ls 3 9l connecting rod bearing torque

2001 Toyota Echo Transmission and Drivetrain Removal And Installation Manual

0

Filed Under (Toyota Manuals) by admin on 10-03-2012

download
REMOVAL 1. REMOVE HOOD HINT: At the time of installation, please refer to the following item. Adjust the hood. 2. REMOVE WIPER ARM HINT: At the time of installation, please refer to the following item. Adjust the installation position of the wiper arms 3. REMOVE RH AND LH COWL TOP VENTILATOR LOUVERS 4. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 4 nuts and No. 2 cylinder head cover. Torque: 7.0 Nm (71 kgf-cm, 62 inch lbs.) 5. REMOVE BATTERY AND AIR CLEANER CASE ASSEMBLY WITH AIR HOSE 6. DISCONNECT WIRE HARNESS FROM TRANSAXLE Remove the set bolt of the wire harness clamp. 7. DISCONNECT CONTROL CABLE a. Remove the 2 clips and washers. b. Remove the 2 clips and disconnect the control cables from the transaxle. 8. DISCONNECT CLUTCH RELEASE CYLINDER a. Remove the set bolt of the clutch line. Torque: 4.9 Nm (50 kgf-cm, 43 inch lbs.) b. Remove the 2 set bolts of the clutch release cylinder. Torque: 12 Nm (120 kgf-cm, 9 ft. lbs.) 9. DISCONNECT GROUND CABLE Remove the set bolt of the ground cable from the engine left mounting bracket. 10. DISCONNECT BACK-UP LIGHT SWITCH AND VEHICLE SPEED SENSOR CONNECTORS 11. REMOVE 2 TRANSAXLE UPPER SIDE MOUNTING BOLTS Torque: 33 Nm (340 kgf-cm, 25 ft. lbs.) 12. REMOVE STARTER SET BOLT Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 13. ATTACH ENGINE SLING DEVICE TO ENGINE HANGER Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print a. Remove the bolt. b. Install the 2 No. 1 engine hangers with the bolts in the correct direction. Parts No.: No. 1 engine hanger: 12281-21010 Bolt: 91642-81025 Torque: 40 Nm (400 kgf-cm, 29 ft. lbs.) c. Attach the engine chain hoist to the engine hangers. CAUTION: Do not attempt to hang the engine by hooking the chain to any other part. 14. RAISE VEHICLE CAUTION: Make sure that the vehicle is securely supported. 15. REMOVE LH ENGINE UNDER COVER 16. DRAIN TRANSAXLE OIL Oil grade: API GL-4 or GL-5 Viscosity: SAE 75W-90 Capacity: 1.9 liters (2.0 US qts, 1.7 Imp. qts) Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 17. REMOVE RH AND LH FRONT DRIVE SHAFTS 18. REMOVE SUSPENSION MEMBER a. Remove the 2 set nuts and bolt of the engine rear mounting insulator from the suspension member. b. Disconnect the sliding yoke. c. Power steering: Disconnect the pressure feed and return tubes. d. Power steering: Disconnect the tube clamp

Related Content:

torque clutch converter solenoid problems 2001 isuzu rodeo, 2004 chevy tahoe 5 3 air conditioner belt tensioner bolt torque specs, 2006 nissan navara d40 cylinder head bolt tightening, 6sa1 flywheel injector settings, flywheel bolt torque 3406b, how to adjust clutch pedal on toyota echo

1999-2006 TOYOTA TUNDRA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the passenger sides of the vehicle. Next remove the wheels from both sides. 2. Using a 17mm socket, remove the lower sway bar link bolt from both sides. HINT: If the stud turns together with the nut use a hex wrench or vice grips to hold the stud . 4. Next remove the strut’s lower mounting bolt with a 19 mm socket and wrench. NOTE: Once the nut is removed, it may be necessary to use a punch and hammer to free the bolt. 5. Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 6. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the steel strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 7. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the steel spacer the strut will be rotated 180° when reinstalled. 8. Place strut back into upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 9. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. 10. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 11. Repeat Steps 3 through 10 on the opposite side of the vehicle. 12. Reattach the sway bar link assembly on both sides of the vehicle. Torque to OEM specs. For 2wd trucks skip Step 13. 13. For 4×4 models only it is necessary to lower the differential using the provided spacers and bolts. Install the spacers following the instructions provided with the spacers. 14. Reattach the wheels. Torque to OEM specs. 15. Lower vehicle to the ground and torque strut mounts to OEM specs. 16. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs 04 gmc yukon, torque specs 4 8 chevrolet, torque specs for 5 7 volvo penta exhaust manifold, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs

Toyota Front Coil Spring Spacer Lift Kit Installation Manual

0

Filed Under (Toyota Manuals) by admin on 22-12-2011

download
INSTALLATION INSTRUCTIONS FRONT 1. Read complete instructions before beginning installation, the following special tools are recommended: Coil spring compressor, floor jack, ball joint separator, jack stands, bench vise, and metric hand tools. 2. Jack the vehicle in the center of the front cross member. 3. Support the vehicle by placing jack stands on the frame cross member so that the front tire/wheels are off the ground. 4. Remove the front tires/wheels. 5. Disconnect the sway bar end links and remove the upper ball joint cotter pin and nut. 6. Separate the upper ball joint from the spindle. (Using ball joint separator or a suitable tool, be careful NOT to damage the ball joint boot) 7. Remove upper strut tower nuts holding strut assembly to strut tower (3) on each side of vehicle. 8. Remove the lower strut bolt from the lower control arm and remove the strut assembly from the vehicle. (Note the direction of the bolt for reinstallation) 9. Compress the coil spring on the strut assembly with a suitable coil spring compressor so that the coil spring has about 3/8″ play in the strut and remove the upper strut isolator mount nut. 10. Remove the coil spring isolator from the upper strut mounting plate. 11. Replace the upper strut mounting plate studs with the supplied studs with a bench vise and a deep well socket. (3 on each side) 12. Reinstall the factory coil spring isolator to the upper strut mounting plate. 13. Reinstall the compressed coil spring onto the strut assembly and reattach the upper strut mount plate using the stock hardware. See diagram. Torque upper strut mounting plate nut to 18 foot-pounds. 14. Decompress the coil spring in the strut assembly. Make sure that the spring is seated correctly into the strut assembly alignment indentation at the bottom of the strut and the top isolator. 15. Slide the coil spring spacer onto the top of the strut assembly over the 10mm studs. 16. Install the strut assembly into the strut tower and start the upper three 10mm lock nuts. (Make sure that the bottom of the strut is aligned as well) 17. Install the lower strut bolt in the original position and torque to 100 foot- pounds. (Step 8) 18. Using the floor jack, raise the lower control arm and connect the upper ball joint on the upper control arm to the spindle. Torque nut to 80 ft lbs. and make sure that you replace the cotter pin. (Not supplied) 19. Install the front tires/wheels. 20. Lower the vehicle onto the ground and tighten the upper strut tower 10mm nuts. Torque to 35 foot-pounds. (3 on each side) 21. RETORQUE ALL BOLTS AFTER 500 MILES.

Related Content:

what checks would you carry out before and after fitting a macpherson strut, sienna manual powered struts open manually, how man ft lbs for cadilla dts strut, how to replace upper strut mounts on a 2002 buick, how to replace front strut assembly 06 dakota, how to install lift support struts on 2006 Toyota Sienna, How to install lift gate struts, how to change out hatch struts on a toyota sienna, honda pilot strut replacement, Front strut replacement 1997 Ford Thunderbird

1999 Honda Civic EX TORQUE SPECIFICATIONS

0

Filed Under (Honda Manuals) by admin on 04-02-2012

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Related Content:

pontiac vibe head torque secuensia, 1999 honda civic door bolt torque specifications, tork settings for fd 42 engine, nuts&bolts service, nissan fd42 tuning, j35 honda bolt pattern transmission, how to rebuild a saturn 1 9 sohc, honda generator bolt torque spec, head bolt torque specifications 2000 buick century, fd42 manifold gasket

1991 Saab 9000 L4-2290cc 2.3L DOHC Turbo EFI Axle Shaft Removal And Installation Manual

0

Filed Under (Saab Manuals) by admin on 04-06-2012

download
Service and Repair Notes Removal Important: Thorough cleanliness must be observed during all work on drive shafts and drive shaft joints, to prevent dirt and dust getting into the joints. Before starting work, always clean the wheel arch, MacPherson strut and other areas around the drive shaft and joints. 1Unfasten the hub centre-nut. 2Lift the car and remove the wheel. 3Remove the hub centre-nut. Push the axle stub back approx. 2 cm (if it pushed further back it can damage the tripod). Use puller 87 91 287 and puller arms 87 91 303 together with tool 87 91 154, puller bracket, the belongs to tool collection for manual gear boxes. 4Remove the steering-swivel member from the MacPherson strut and unfasten the flexible hose from the hose mounting and, if appropriate, also unfasten the ABS sensor and cable. Important: Scrupulously clean the rubber gaiter and the universal joint driver. 5Remove the clamp securing the rubber gaiter on the inner universal joint driver. Pull the universal joint apart and fit the protective cover on the rubber gaiter and universal joint driver. 6Pull out the drive shaft from the hub. Fitting 1Remove existing grease out of the universal joint driver and carefully clean the interior. 2 Pack the universal joint driver with grease, 60 g Mobile K 575 GS. Observe great cleanliness. Motor / ALLDATA Online – 1991 Saab 9000 L4-2290cc 2.3L DOHC T… http://www.motoralldata.com/alldata/MOTOR~V71595976~C19965~… 3 of 4 3/26/2008 12:03 AM Zoom Sized for Print

Related Content:

haynes saab 9-3 pdf download

FORD E450 CUTAWAY OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the front and rear bolts from the leaf spring. 2. Remove existing U-bolts and U-bolt plate that attach the axle to the leaf spring . Remove the leaf spring from the axle. 3. Remove the front spring hanger bracket , rear leaf spring hanger bracket, and any overload spring brackets . See Figure 2-1. These can be removed by grinding, or air chiseling, the heads off the factory-installed rivets, and using a hammer and punch to remove remainder of the rivet. See Figure 2-2. 3. Remove the OEM shock absorbers and retain the lower mounting fastener for later use. 4. Cut the exhaust as it bends downward after the axle, at its most vertical and straight section. See Figures 2-3 & 2-4. Save the cut-off portion for use in Section 9. Remove the rear exhaust hanger from the frame. CAUTION: Be careful that the leaf spring does not spring out of its hanger, or off the frame. FIG. 2-4 FIG. 2-1 FRONT HANGER BRACKET FIG. 2-2 LEAF SPRING REAR HANGER BRACKET FIG. 2-3 CUT HERE FOR EXHAUST MODIFICATION 6 3. DRIVER SIDE ASSEMBLY 1. Review Figure 3-1 & Figure 11-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using the (4) 7/16 x 1 1/4 UNC FLANGE BOLTS and (4) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . 3. Loosely secure the suspension Arm to the axle using (2) 5/8 UNF, 4.0 X 10.50 U-bolts, (4) 5/8 WASHERS, (4) 5/8 UNF HIGH NUTS, and the Arm Mount Plate. Make sure the locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. Note : Install the axle tube spacer between the U-bolts and Axle when installing on an E350. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the Arm to the Front Hangar using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Using the enclosed bolt hole template for the Upper Air Spring Mount, align the template to the frame using the appropriate rear spring hanger holes. Mark and drill three (3) new frame holes to 0.47″ on each side of the frame. Bolt the air spring bracket assembly to the frame using (5) 7/16 x 1 1/4 UNC CAPTIVE BOLTS and (5) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . Note : Use the correct holes designated for either the E350 or E450 chassis. See Figure 3-2. 6. Bolt the air spring to the suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut. (See Table 11-1 for appropriate Torque) . FIG. 3-2 E450 HOLE PATTERN E350 HOLE PATTERN TEMPLATE OE REAR HANGER MOUNT HOLES FRAME FIG. 3-1 AIR SPRING ARM MOUNT PLATE AXLE TUBE SPACER WEAR WASHER TRAILING ARM U-BOLT FRONT HANGER BRACKET AIR SPRING MOUNT BRACKET 7 AFTER BOTH SIDES HAVE BEEN INSTALLED (Sections 4, 5, 6) FINISH THE FOLLOWING STEPS: 7. Tighten the Arm bushing bolts and the Arm U-bolts AFTER the suspension has been installed and brought to Design Height, in Section 9.5. (See Table 11-1 for appropriate Torque) . 8. Install the new shock absorbers using the same orientation as factory, with factory and enclosed hardware. 9. IMPORTANT: Route the brake cable away from the air spring and any other moving components. It may need to be tied, or slightly repositioned in order to accommodate this. 4. PASSENGER SIDE DISASSEMBLY 1. Repeat Section 2 for the passenger’s side of the truck. 5. PASSENGER SIDE ASSEMBLY 1. Repeat Section 3 for the passenger’s side of the truck. Double-check all fasteners for proper torque. Check all clearance points and all alignments. See Figure 5-1 for details.

Related Content:

2002 rondevious change rear spring, f150 1995 changing front leaf spring brackets, head bolts torque on 2001 2 5 ford ranger, how to replace 2000 chevy cavalier exhaust bracket, how to replace mazda 3 rear coil springs, is there a metal washer before e clip on pitman arm seal gearbox on a 1997 ford f150, tie rod end at pitman armnut torque 2000 f350 7 3l 4wd, Trailing Arm bracket for 2000 Buick Century

2003-2007 Accord V6 Power Steering Moans or Whines Repair Manual

0

Filed Under (Toyota Manuals) by admin on 02-06-2012

download
SYMPTOM A moan or whine is heard when turning the steering wheel when the engine is cold. There may be air bubbles or foam in the power steering reservoir. The noise usually goes away when the engine warms up. PROBABLE CAUSE Air enters the power steering pump through the inlet joint O-ring. CORRECTIVE ACTION Replace the O-ring on the power steering pump inlet joint. PARTS INFORMATION O-ring: P/N 91345-RDA-A01, H/C 8811010 REQUIRED MATERIALS Honda Genuine Power Steering Fluid: P/N 08206-9002, H/C 3747284 (One container repairs about 12 vehicles.) WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 5121B5 Flat Rate Time: 0.3 hour Failed Part: P/N 91345-PAA-A01 H/C 5430681 Defect Code: 07408 Symptom Code: 04201 Template ID: 07-086A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE 1. Remove the bolt holding the inlet joint to the power steering pump housing. 2. Place a shop towel under the inlet joint. 3. Twist the inlet joint back and forth until it is loose, then carefully disconnect the joint and point the hose upward to minimize fluid loss. 4. Remove the inlet joint O-ring. 5. Apply power steering fluid to a new O-ring, and install it on the inlet joint. 6. Install the inlet joint, and torque its bolt to 11 N. m (8 lb-ft). 7. Top off the power steering fluid, if needed. Start the engine, and let it idle. Confirm that the noise is gone and that the system is operating properly

Related Content:

corvette c4 tech free pdf, HC - 8811010

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, how to replace rear upper arm kia sedona, torqe for ball joint 2001 prizm, oem ball joint press, peugeot 306 front lower arm removal, lower ball joint press sedona kia, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000