Skip to content

1999 jaguar xj8 engine diagrams timing

You search PDF repair manual about 1999 jaguar xj8 engine diagrams timing, if there are search results will appear below. If search results do not exist, please search by others keyword.

3406E Truck Engine Installation OR Removal Of The Speed/ Timing Sensor

download
1. Disconnect the speed/timing connector “P9/J9″ (2) . Inspect the connector for the following conditions. * Corrosion * Bent pins * Missing pins * Damaged sockets * Mismating * Broken wires 2. Remove the Speed/timing sensor (1) from the front gear cover. 3. Examine the plastic end of the sensor for signs of wear or contaminants such as metal filings. The plastic end of the speed/timing sensor should have no contaminants and should show no wear (greater than 0.051 mm (0.0020 inch) from the face) . 4. Use a screwdriver to carefully pry the plastic sensor end to the fully extended position (approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor). 5. Gently push in on the plastic end of the sensor. The plastic end should be firm. The plastic end should resist movement in the retract direction. If there is no resistance replace the sensor 6. Remove the two bolts (3) and remove the cover (5) from the flywheel housing. This hole is used for engine turning. 7. Put one bolt (3) in the timing bolt location (4) . The timing bolt location is approximately 127 mm to 152 mm (5 inch to 6 inch) above the hole in the flywheel housing for engine turning. I 8. Use 9S-9082 Engine Turning Tool (6) and a 1/2 inch drive ratchet wrench to turn the engine flywheel in the direction of normal engine rotation. The normal engine rotation is in a counterclockwise direction when viewed from the flywheel end. Turn the engine flywheel until the timing bolt engages with the threaded hole in the flywheel. Note: Visually check the location of the tooth on the wheel on which the speed/timing sensor is to be positioned. The end of the sensor must be in alignment with a tooth on the wheel and not in alignment with the valley of the wheel. Note: The No. 1 piston must be at either top center of the compression stroke or at top center of the exhaust stroke. 9. Inspect the speed/timing sensor before installation. Use steps 3 through step 6 to inspect the sensor. 10. If the sensor end is not fully extended, use a screwdriver to carefully pry the plastic sensor end to the fully EXTENDED position approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor.

1999 Volkswagen New Beetle GL timing belt replacement manual

download
REMOVAL & INSTALLATION NOTE: For 2004, manufacturer does not provide a timing belt replacement interval. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Engine code AEG is stamped into machined pad on front of cylinder block above crankcase breather, near cylinder head mating surface. See Fig. 1 . For all other 2.0L engines, engine code is stamped on transmission mating flange at the rear of the engine. See Fig. 2 . For all engines, code can also be found on the vehicle data plate and on a sticker on the timing belt cover. Fig. 2: Locating Engine Identification Code (AVH, AZG, BDC & BEV) Courtesy of VOLKSWAGEN UNITED STATES, INC. TIMING BELT Removal (AEG, AVH, AZG, BEV & BDC Engine Codes) 1. Remove right hand insulation tray from engine compartment. Remove engine cover. Rotate serpentine belt tensioner clockwise to relieve belt tension. Remove serpentine belt. See Fig. 3 . Lock in place using Mandrel (T10060) or a drift. Fig. 3: Releasing Serpentine Belt Tensioner Courtesy of VOLKSWAGEN UNITED STATES, INC. 2. Remove serpentine belt tensioner assembly. See Fig. 4 . Turn crankshaft to TDC position. See Fig. 5 . Align TDC marks visible in bellhousing access hole. See Fig. 6 . Remove upper timing belt cover. Ensure camshaft sprocket timing mark aligns with mark on rear cover. See Fig. 5 . 3. Support engine from above or below with floor jack to take engine weight off of mounts. Remove coolant reservoir and set aside. On Golf and Jetta, remove power steering reservoir (hoses attached), and set aside. On New Beetle, pull off EVAP hoses at EVAP canister and throttle valve housing. 4. On all models, remove engine mount from timing belt end of engine. See Fig. 7 . Remove crankshaft pulley from crankshaft sprocket. It is NOT necessary to remove center bolt (center bolt is torque-to-yield type that must be replaced if removed). 5. Remove timing belt covers. Remove engine support from front of engine. See Fig. 4

1999 Daewoo Lanos SE TIMING BELT REMOVAL And INSTALLATION MANUAL

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove the air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove accessory drive belts. See Fig. 1 . 3. Remove power steering pump pulley bolts (if equipped). Remove power steering pump pulley. Remove crankshaft pulley center bolt. Remove crankshaft pulley. Lower vehicle. 4. Remove upper and lower timing belt covers. See Fig. 2 . Remove power steering pump mount bolts (if equipped). Set power steering pump aside with hoses attached. 5. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 3 . Ensure camshaft sprocket timing marks face each other. See Fig. 4 . 7. Slightly loosen water pump bolts. Using Timing Belt Adjuster (J-42492), rotate water pump counterclockwise to relieve tension on the timing belt. See Fig. 5 . Remove timing belt

1999 Jaguar XJ8 Vanden Plas SUSPENSION ADJUSTMENTS And Installation Manual

download
ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES HUB BEARING PRELOAD Hub bearing preload is controlled by shim adjustment between hub assembly and hub outer bearing. Shims are available in various thicknesses. Checking 1. Raise and support vehicle. Remove wheel assembly. Clamp dial indicator mount to hub carrier. Ensure dial indicator pointer contacts hub flange. 2. Using 2 levers between hub and hub carrier, press hub outward. Note reading on dial indicator. The difference between dial indicator readings is preload of hub bearing. For adjustment, see HUB CARRIER under REMOVAL & INSTALLATION. REAR SUSPENSION HEIGHT 1. Ensure vehicle has full fuel tank, all fluids are topped off and tire pressures correct. Roll vehicle about 30 feet on a level surface. Measure distance between differential support plate at both sides and ground. See Fig. 2 . 2. Height measurement for coupe and convertible. If height is not within specification, check all bushings and replace as necessary. If bushings are okay, replace rear springs. NOTE: See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. 1999 Jaguar XJ8 Vanden Plas 1999-2000 SUSPENSION’ ‘Rear Fig. 2: Measuring Rear Suspension Height Courtesy of JAGUAR CARS, INC. REMOVAL & INSTALLATION “A” FRAME Removal 1. Raise vehicle and support with stands. Remove “A” frame to final drive unit rear bracket securing bolts and front bracket inner securing nuts and bolts. See Fig. 3 . 2. Position a suitable wood and jack under final drive unit drive flange, operate jack to support final drive unit. Unscrew and remove both “A” frame outer bush to body and bracket securing bolts. See Fig. 4 . Unscrew and remove “A” frame left and right outer bush bracket to body securing bolts. 3. Lower jack approximately one inchto improve access. Unscrew and remove “A” frame to final drive unit front bracket intermediate securing bolts. Unscrew and remove “A” frame to final drive unit fron

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check