Skip to content

1999 vw beetle how to remove center console with automatic transmission

You search PDF repair manual about 1999 vw beetle how to remove center console with automatic transmission, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Volkswagen New Beetle GL timing belt replacement manual

download
REMOVAL & INSTALLATION NOTE: For 2004, manufacturer does not provide a timing belt replacement interval. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Engine code AEG is stamped into machined pad on front of cylinder block above crankcase breather, near cylinder head mating surface. See Fig. 1 . For all other 2.0L engines, engine code is stamped on transmission mating flange at the rear of the engine. See Fig. 2 . For all engines, code can also be found on the vehicle data plate and on a sticker on the timing belt cover. Fig. 2: Locating Engine Identification Code (AVH, AZG, BDC & BEV) Courtesy of VOLKSWAGEN UNITED STATES, INC. TIMING BELT Removal (AEG, AVH, AZG, BEV & BDC Engine Codes) 1. Remove right hand insulation tray from engine compartment. Remove engine cover. Rotate serpentine belt tensioner clockwise to relieve belt tension. Remove serpentine belt. See Fig. 3 . Lock in place using Mandrel (T10060) or a drift. Fig. 3: Releasing Serpentine Belt Tensioner Courtesy of VOLKSWAGEN UNITED STATES, INC. 2. Remove serpentine belt tensioner assembly. See Fig. 4 . Turn crankshaft to TDC position. See Fig. 5 . Align TDC marks visible in bellhousing access hole. See Fig. 6 . Remove upper timing belt cover. Ensure camshaft sprocket timing mark aligns with mark on rear cover. See Fig. 5 . 3. Support engine from above or below with floor jack to take engine weight off of mounts. Remove coolant reservoir and set aside. On Golf and Jetta, remove power steering reservoir (hoses attached), and set aside. On New Beetle, pull off EVAP hoses at EVAP canister and throttle valve housing. 4. On all models, remove engine mount from timing belt end of engine. See Fig. 7 . Remove crankshaft pulley from crankshaft sprocket. It is NOT necessary to remove center bolt (center bolt is torque-to-yield type that must be replaced if removed). 5. Remove timing belt covers. Remove engine support from front of engine. See Fig. 4

1999 Ford Windstar Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the steering wheel. Refer to Section 211-04 . 2. Remove the passenger side air bag module. Refer to Section 501-20B . 3. Disconnect the antenna in-line connector. 4. Remove the RH instrument panel reinforcement bolt. 5. Close the glove compartment. 6. Remove the utility compartment. 1. Remove the four two part pin type retainers. 2. Remove the utility compartment. * Disconnect the power point electrical connector. 7. If equipped, disconnect the compact disc changer electrical connector. 8. Release the compact disc changer electrical connector locator. 9. Remove the LH and RH scuff plates. 10. Remove the LH and RH A-pillar lower trim panels. 11. Position the LH and RH front door weatherstrip seals aside. 12. Remove the RH ground bolts. 13. If equipped, remove LH and RH instrument panel lower insulators. 14. Remove the instrument panel lower steering column opening cover. 1. Remove the screws. 2. Remove the instrument panel lower steering column opening cover. 15. Remove the instrument panel opening cover reinforcement. 1. Remove the bolts. 2. Remove the instrument panel opening cover reinforcement. 16. Disconnect the LH wiring harness electrical connectors. 17. Disconnect the electronic crash sensor (ECS) electrical connector. 1. Release the locking clip. 2. Disconnect the ECS electrical connector 18. Disconnect the automatic transmission shift cable. 1. Disconnect the cable from the steering column shift tube lever. 2. Disconnect the cable from the steering column bracket. 19. Separate the intermediate shaft from the steering column. 1. Remove the pinch bolt. 2. Separate the intermediate shaft from the steering column. 20. Disconnect the climate control harness electrical connector. 21. Disconnect the climate control vacuum harness connector. 22. Disconnect the fuse junction panel electrical connectors. 23. Remove the LH instrument panel reinforcement bol 4. Remove the four instrument panel center support bolts. 25. Remove the instrument panel defroster opening grille. * If equipped, disconnect the sunload sensor electrical connector. 26. Remove the cowl top bolts. 27. Remove the RH cowl side bolts. 28. Remove the LH cowl side bolts. 29. NOTE: Two technicians are required to carry out this step. Remove the instrument panel. Installation CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. NOTE: Two technicians are required to carry out this step

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

2004 Honda Accord LX CENTER CONSOLE REMOVAL/ INSTALLATION MANUAL

download
CONSOLES CENTER CONSOLE REMOVAL/INSTALLATION 1. M/T model: Remove the shift knob (A). a. Lower the shift lever boot (B) to release the hook (C) from the knob. b. Remove the shift knob. Fig. 34: Removing The Shift Knob 2. Detach the clips (A, B) by pulling the center console front panel (C) up, If equipped, disconnect the seat heater switch connectors (D). Fig. 35: Detaching The Clips 3. Pry up on the left of the console pocket (A) with a flat-tip screwdriver wrapped with a shop towel, and detach the clips, then remove the pocket. Fig. 36: Removing The Pocket 4. Remove the screws (A), detach the clips (B) and hook (C) by pulling the center holder (D) up, and disconnect the front accessory power socket connector (E) Fig. 37: Disconnecting The Front Accessory Power Socket Connector 5. Detach the clips (A, B) by pulling the center console rear panel (C) up Fig. 38: Detaching The Clips 6. Remove the center console (A). a. Open the console box lid (B) then remove the console mat (C). b. If equipped, disconnect the rear accessory power socket connector (D), and detach the clip (E). c. Remove the screws (F, G), then pull the rear portion of the console up to release the hooks (H), then remove it.

2000 Chevy Truck S10/T10 Instrument Panel (I/P) – Carrier Replacement

download
REMOVAL PROCEDURE 1. On vehicles equipped with a manual transmission, remove the shift lever. 2. On vehicles equipped with an automatic transmission, perform the following steps: CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 3. Disconnect the battery negative cable. CAUTION: Refer to SIR Handling Caution in Service Precautions. 4. Disable the passenger side SIR system. 5. Remove the left sound insulator. 6. Remove the right instrument panel sound insulator. 7. If the vehicle is equipped with a multiple CD changer located in the center console, remove the center console. 8. Remove the center sound insulator. 9. Remove the lower left instrument panel mounting bolt. 10. Remove and retain the instrument panel storage compartment. 11. Remove the lower right instrument panel mounting bolt. 12. Remove and retain the left and right speakers and the speaker grilles. 13. Use a flat-bladed tool to remove the windshield defroster grille. Retain the windshield defroster grille for use on the replacement IP carrier. 14. If the vehicle is equipped with a sunload sensor, twist the sunload sensor 1/4 turn counterclockwise in order to detach it from the windshield defroster grille. Retain the sunload sensor for use on the replacement IP carrier. IMPORTANT: Always disconnect the brown electrical from the BCM before disconnecting the purple electrical connector from the BCM. 15. Disconnect the brown electrical connector from the Body Control Module ( BCM ) . 16. Disconnect the purple electrical connector from the Body Control Module (BCM) . 17. Remove the knee bolster. 18. Remove and retain the instrument panel cluster. 19. Remove and retain the radio. 20. Remove and retain the HVAC control assembly 21. Remove the left and right instrument panel driver knee bolster brackets. 22. Lower the steering column for clearance. Refer to the appropriate procedure: * Steering Column Replacement in Steering Wheel and Column – Standard * Steering Column Replacement in Steering Wheel and Column – Tilt IMPORTANT: Label all of the connections in order to avoid improper installation