Skip to content

1fz test toyota igniter

You search PDF repair manual about 1fz test toyota igniter, if there are search results will appear below. If search results do not exist, please search by others keyword.

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

1995 Toyota 4Runner STARTING AND CHARGING SYSTEMS REPAIR MANUAL

download
TROUBLE SHOOTING NOTE: See TROUBLE SHOOTING – BASIC PROCEDURES article in GENERAL INFORMATION. 1) If a no-start condition exists and battery is known to be good, connect test light or voltmeter between starter solenoid terminal No. 50 and ground. See Figs. 6 and 7. 2) Turn ignition switch to START position. If test light or voltmeter does not indicate voltage, check main fusible links and large ampere main fuses in engine compartment relay box. If fusible links and fuses are okay, see IGNITION SWITCH CONTINUITY TEST and/or STARTER RELAY TEST under ON-VEHICLE TESTING. ON-VEHICLE TESTING NOTE: Before testing, ensure battery is fully charged, battery cables and terminal ends are tight and clean, and engine grounds are secure. CLUTCH START SWITCH TEST 1) Switch is located above clutch pedal on bracket. Disconnect wiring harness connector from switch. 2) Connect ohmmeter probes to switch terminals. Depress clutch pedal. If continuity does not exist, adjust or replace clutch start switch. If continuity exists, check circuit to starter relay for open, and check starter relay. See STARTER RELAY TEST. CLUTCH START CANCEL SWITCH TEST 1) Locate switch in left dash panel. Remove right lower instrument panel to access switch connector. Disconnect wiring harness connector from switch pigtail connector. See Fig. 1. 2) Connect negative lead of ohmmeter to terminal No. 1. Ensure continuity does not exist between connector terminals No. 1 and 2, terminals No. 1 and 3, and terminals No. 2 and 3. Check operation of switch by connecting jumper wires from 12-volt battery. Connect positive lead to terminal No. 3 and negative battery lead to terminal No. 1. 3) Using ohmmeter, ensure continuity does not exist between connector terminals No. 1 and 2 until switch button is pushed. When switch button is pushed, switch light should come on and continuity should exist. Disconnect battery and ensure continuity does not exit between terminals No. 1 and 2. If switch does not test as specified, replace switch. Fig. 1: Identifying Clutch Start Cancel Switch Connector Terminals Courtesy of Toyota Motor Sales, U.S.A., Inc. IGNITION SWITCH CONTINUITY TEST WARNING: Deactivate air bag system before performing any service operation. For 1996 4Runner, see AIR BAG RESTRAINT SYSTEM article. 1995 1) Disconnect negative battery cable. Removedriver’s lower instrument panel cover. Remove upper and lower steering column covers if needed. Locate ignition switch wiring harness 8-pin connector. See Figs. 2-3. 2) With ignition switch in LOCK position, there should be no continuity between any terminals. With ignition switch in ACC position, there should be continuity between terminals No. 2 and 3. With ignition switch in ON position, there should be continuity between terminals No. 1, 2 and 3, and between terminals No. 7 and 8. 3) With ignition switch in START position, there should be continuity between terminals No. 1, 4 and 6, and between terminals No. 7 and 8. If continuity is not as specified, replace switch.

Wiring Toyota Switch to SH-R-00 Carbon Fiber Seat Heater

download
Wiring Toyota Switch to SH-R-00 Carbon Fiber Seat Heater (Switch is ready to use with FWSH-U-00 FlexWire Seat Heater) SH-R-EXT (rev 0) Harness plug: Black, White, Red, Green Toyota Switch Pigtail CarbonFiber Harness Extn To use the Toyota Switch with SH-R-00 Carbon Fiber Seat Heater kit, you will need to direct connect the wires, eliminating the modular plugs on both the harness extension and switch. 1. Cut the plug end off the Toyota switch pigtail harness. 2. Cut the end plug off the wire harness extension. 3. Attach spade connectors to each wire. 4. Cross connect the wires as shown. 5. Test switch before mounting

2000-2004 Toyota Sequoia Lower Grille Installation Manual

download
1. Decided you want to customize the look of your Toyota Sequoia? This is what you are looking at now and below is the improvement that this grille will make. 2. Tools Required: Gloves- for your hands sake (there might be some sharp edges), a towel (or something soft to lay your grille onto), needle nose pliers, and maybe some sheers. 3. Identify the FRONT side of the grille. The back side has the stamping droop. We try to label the back with a sticker, if you have trouble getting it off try some rubbing alcohol. 4. Test the fitment of the grille in the lower opening of the Sequoia. Notice that there is a top and bottom as well to the shape of the grille. 5. If you need to do some fine tuning, remove the grille, take off a portion of the push-on edge guard and trim the grille with a pair of sheers. Then reinstall the edge guard and test again. This is generally not a required step. 6. With the grille located into place now and the fit is good, you need to open your hood. 7. With the hood up your hands can reach the back-side of the black plastic mesh grille that came on your sequoia. 8. Place the grille into position and with one of your hands hold it in position. With the other hand insert a zip-tie from the back of the grill in three locations (one on both sides and one in the middle). After you insert the zip-tie with the lug of the zip-tie on the inside (behind the grille), then feed it back through, tighten it up and clip off the extra zip-tie. 9. To keep clean we recommend Aluminum Polish that can be purchased at auto parts stores. It only requires hand polishing. This is an aftermarket automotive component and thus we make no warranty for any part of the vehicle. Use at your own risk