2000 bonneville transmission speed sensor install

You search PDF repair manual about 2000 bonneville transmission speed sensor install, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2000 bonneville transmission speed sensor install Direct Download speed 5432 Kb/s

  2000 bonneville transmission speed sensor install Full Version speed 8172 Kb/s



4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, 2011 crv engine whine, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio, how to adjust the bands of an automatic trasmission of hyundai accent 2002

1999 Jeep Grand Cherokee Limited AUTOMATIC TRANSMISSIONS Chrysler 45RFE Electronic Controls Repair Manual

0

Filed Under (Jeep Manuals) by admin on 11-07-2012

download
INTERNAL TCM Circuit Description The TCM is reporting internal errors. Diagnostic Procedure 1. Turn ignition switch to LOCK position. Remove transmission control relay. Measure resistance between ground and relay ground circuit (Black/Yellow wire) in relay connector. If resistance is greater than 5 ohms, repair open circuit. If resistance s not greater than 5 ohms, go to next step. 2. The TCM has an internal problem and must be replaced. P0715: INPUT SPEED SENSOR ERROR Circuit Description DTC P0715 will set if an excessive change in input RPM has been detected in any gear. Possible Causes * Intermittent wiring and connector problems. * Faulty input speed sensor. * Input speed sensor circuits shorted to ground, shorted to voltage, or open. * Faulty TCM. Diagnostic Procedure 1. Place gear selector in “P” position and start engine. Using scan tool, monitor input speed sensor value. If value is less than 400 RPM, go to next step. If value is not less than 400 RPM, go to step 9. 2. Turn ignition switch to LOCK position. Install Transmission Simulator (8333). Turn ignition on. Using transmission simulator, turn rotary knob to middle (1000/3000) position. Turn INPUT/OUTPUT switch on. Using scan tool, monitor input and output speed sensor values. If input speed sensor value is 2950- 3050 RPM and output speed sensor value is 950-1050 RPM, replace input speed sensor. If speed sensor values are not as specified, go to next step. 3. Turn ignition switch to LOCK position. Disconnect TCM harness connector. Remove transmission control relay. Using fused jumper wire, jumper fused B+ circuit (Red/White wire) and transmission relay output circuit (Red wire) together at relay connector. Turn ignition on. Measure voltage between ground and input speed sensor signal circuit (Red/Black wire) at TCM harness connector. If voltage is greater than 3 volts, repair circuit for short to voltage. If voltage is not greater than 3 volts, remove jumper wire, install relay and go to next step. 4. Turn ignition switch to LOCK position. Disconnect input speed sensor harness connector. Measure resistance of input speed sensor signal circuit (Red/Black wire) between TCM and input speed sensor. If resistance is greater than 5 ohms, repair open circuit. If resistance is not greater than 5 ohms, go to next step. 5. Measure resistance of input speed sensor ground circuit (Dark Blue/Black wire) between TCM and input

Related Content:

yhs-fh_lsonsw, kia rondo input speed sensor, asc spoiler sunroof wont close grand cherokee, How to remove back up sensor on 2012 explorer rear bumper, WHERE IS THE FUSE PANEL IN A 1986 TOYOTA PICKUP, where is the transfer case speed sensor on a avalanche, where is the rpm sensor for a kia sedona, where is the out put shaft speed sensor located on a 2003 lincoln navigator?, location of the yaw sensor on a hummer h3, where is turbine speed sensor located on 2009 pontiac vibe

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to remove 2011 dodge durango grill, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, 2005 buick lesabre instrument cluster removal, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

2000 Chevy Truck S10/T10 Blazer Transfer Case Removal And Installation Manual

0

Filed Under (Chevy Manuals) by admin on 18-05-2011

download
Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case. 12. For vehicles equipped with a manual transmission, remove the six nuts securing the transfer case and bracket to the transmission 13. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 14. For vehicles equipped with a automatic transmission, remove the six nuts securing the transfer case and bracket to the transmission adapter. 15. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 16. Remove and discard the gasket. Installation Procedure 1. Install a new gasket to the transmission. Use sealer GM P/N 12346004 in order to hold the gasket in place. 2. Raise and position the transfer case to the vehicle Notice: Refer to Fastener Notice in Service Precautions. 3. For vehicles equipped with a automatic transmission, install the six nuts securing the transfer case and bracket to the transmission adapter. * Tighten the nuts to 47 Nm (35 lb ft) . 4. For vehicles equipped with a manual transmission, install the six nuts securing the transfer case and bracket to the transmission. * Tighten the nuts to 47 Nm (35 lb ft)

Related Content:

wiring for case w20 loader, case 444-75 repair manuals free, How to rebuild Kia Sorento Transfer Case, Case 1845C Manual Download, np 208 service manual, toyota tacoma ground wire transfer case, Chevy NP208 Rebuild Instructions, 2001 ford sports trac 4x4 transfer case wiring diagram, f150 transfer case problems, ford 2003 ford explorer how transfer case works

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, how to check radiator fluid level pontiac grand prix, Low coolant light olds intrigue, evap sensor on 2002 suburban, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 2002 mercury sable cooling system, 2006 Envoy low idle

3406E Truck Engine Installation OR Removal Of The Speed/ Timing Sensor

0

Filed Under (More Manuals) by admin on 22-06-2012

download
1. Disconnect the speed/timing connector “P9/J9″ (2) . Inspect the connector for the following conditions. * Corrosion * Bent pins * Missing pins * Damaged sockets * Mismating * Broken wires 2. Remove the Speed/timing sensor (1) from the front gear cover. 3. Examine the plastic end of the sensor for signs of wear or contaminants such as metal filings. The plastic end of the speed/timing sensor should have no contaminants and should show no wear (greater than 0.051 mm (0.0020 inch) from the face) . 4. Use a screwdriver to carefully pry the plastic sensor end to the fully extended position (approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor). 5. Gently push in on the plastic end of the sensor. The plastic end should be firm. The plastic end should resist movement in the retract direction. If there is no resistance replace the sensor 6. Remove the two bolts (3) and remove the cover (5) from the flywheel housing. This hole is used for engine turning. 7. Put one bolt (3) in the timing bolt location (4) . The timing bolt location is approximately 127 mm to 152 mm (5 inch to 6 inch) above the hole in the flywheel housing for engine turning. I 8. Use 9S-9082 Engine Turning Tool (6) and a 1/2 inch drive ratchet wrench to turn the engine flywheel in the direction of normal engine rotation. The normal engine rotation is in a counterclockwise direction when viewed from the flywheel end. Turn the engine flywheel until the timing bolt engages with the threaded hole in the flywheel. Note: Visually check the location of the tooth on the wheel on which the speed/timing sensor is to be positioned. The end of the sensor must be in alignment with a tooth on the wheel and not in alignment with the valley of the wheel. Note: The No. 1 piston must be at either top center of the compression stroke or at top center of the exhaust stroke. 9. Inspect the speed/timing sensor before installation. Use steps 3 through step 6 to inspect the sensor. 10. If the sensor end is not fully extended, use a screwdriver to carefully pry the plastic sensor end to the fully EXTENDED position approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor.

Related Content:

4efe maf sensor, 4L60E VSS Sensor Location, b0091 front end sensor 3 location, cat 3406 e engine sensor locations, front end connector sensor 1

2000 Ford Pickup F250 Super Duty TEST DE: EXHAUST BACKPRESSURE (EBP) SENSOR

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine. Inspect for damaged pins, corrosion and loose wires. Repair as necessary. Measure resistance between ground and Gray/Red wire at EBP sensor wiring harness connector. See Fig. 11 . If resistance is less than 5 ohms, replace EBP sensor. If resistance is 5 ohms or more, locate and repair open circuit in Gray/Red wire. 3) Continuous DTC P0470 This DTC indicates PCM detected a EBP sensor malfunction during normal driving conditions. Possible causes for this DTC are: Faulty EBP Sensor • Faulty Connection • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. While observing EBP PID, wiggle and bend small sections of wiring harness starting at EBP sensor connector and working toward PCM. If EBP reading fluctuates, isolate fault and repair as necessary. If reading does not fluctuate, go to next step. 4) Check Connector Disconnect EBP sensor connector. Sensor is located on top front of engine. Disconnect PCM 104-pin connector. Inspect connectors for damaged pins, corrosion and loose wires. Repair as necessary. Clear DTCs and repeat QUICK TEST . If both connectors are okay, no problem is indicted at this time. 5) DTC P0471 This DTC indicates PCM detected an EBP sensor malfunction during normal driving conditions and with EBP sensor enabled. Possible causes for this DTC are: Faulty EBP Sensor. • Plugged Or Restricted Sensor Supply Tube • Damaged Exhaust Pressure Regulator (EPR) Linkage Or Butterfly Damage • Faulty PCM • Perform KOER ON-DEMAND SELF-TEST . If any DTCs are present, repair fault(s) before continuing with this test. Using scan tool, select EBP PID from PID/DATA monitor menu. Road test vehicle performing hard accelerations while monitoring EBP PID. If EBP reading increases to more than 25 psi with EBP sensor on, no problem is indicated at this time. If EBP reading does not increase to more than 25 psi, go to next step

Related Content:

2007 nissan frontier camshaft position sensor location, Chevy Traverse Bank 2, 2000 Infiniti Q45 Problems, how to check oil in front crank case 2005 tahoe, 02 sensor problems 2010 prius, where is the heat sensor on a 2005 chevy impala?, o2 sensor bank 1 tundra, location of front heated exhaust oxygen sensor Saturn SL two 2002, locate 2011 traverse coolant temperature sensor, install cam sensor kia 05 sedona

1991-1992 Toyota MR2 Turbo, 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 21-09-2011

download
Connector A Pin # Name Function Signal Type A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched Power

1991-1992 Toyota MR2 Turbo 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 18-04-2012

download
A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched

Related Content:

change knock sensor 2005 chevy avalanche, diogram of knock sensor on 1999 lumina, where is the air temp sensor on 2001 toyota celica

1996-2000 Chevrolet And GMC Suburban/ Pick-Up 2500/ 3500 Series TUBULAR EXHAUST SYSTEM INSTALLATION INSTRUCTION

0

Filed Under (Chevrolet Manuals) by admin on 29-12-2011

download
Disassembly – Left Side 1. Disconnect negative cable from battery. 2. Use penetrating oil on all nuts and bolts to be removed. This will prevent the possibility of broken or stripped nuts and bolts. 3. Remove air cleaner system (note position of line and hose connections). 4. Disconnect spark plug wires. 5. Disconnect temperature sensor wire. 6. Remove EGR fitting. 7. Remove bolts and exhaust manifold. Disassembly – Right Side 1. Remove air cleaner box. 2. Disconnect spark plug wires. 3. Remove dipstick and dipstick tube. 4. Remove bolts and exhaust manifold. 5. Clean exhaust flange surfaces on both cylinder heads at this time. DISASSEMBLY – CROSSOVER PIPE 1. Raise vehicle and support with jackstands. 2. Disconnect and remove 02 sensors (2), being careful not to rupture or destroy the unit. WARNING: Do not clean this unit in any cleaning solvent and do not damage wire. 3. Between left and right side of the catalytic converter is a 3-bolt flange with gasket. From the front face of flange, measure out 15″ towards front of truck and cut stock exhaust pipes. Remove exhaust pipes from vehicle. NOTE: Before cutting pipes, measure the height of the converter from the bottom of the floor board for when you install new exhaust pipes you can maintain same distance. •ASSEMBLY – LEFT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer, and thick flat washer at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install left side T.E.S. manifold from bottom side 3. Install all bolts and washers and tighten. Use thick flat washers on slotted holes. 4. Reinstall spark plugs. 5. Replace original equipment spark plug ends on cylinders #3 and #5 with 60° connectors and boots provided in kit. 6. Re-connect spark plug wires on left side. 7. Re-install temperature sensor wire to temperature sensor. ASSEMBLY – RIGHT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer and thick flat washers at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install right side T.E.S. manifold from top side. Now install dipstick tube. 3. Install remaining bolts and lock washers. 4. Align all parts and tighten all right side bolts at this time. 5. Replace original equipment spark plug ends on cylinders #4, #6 and #8 with 60° connectors and boots provided in kit. 6. Re-connect right side spark plug wires. 7. To prevent contact with the hot T.E.S. tubing, use nylon tie wrap (supplied) to secure the heater hose to the a.c. dryer. 8. Re-install air cleaner box. CROSSOVER PIPE ASSEMBLY 1. With catalytic converters in their natural position, install and bolt exhaust extension pipes to header collectors using 3/8″ – 16″ x 2 1/2″ hex bolts, 3/8″ flat washers, 3/8″ lock washers and 3/8 hex nuts. Use the 3″ donut provided in kit. 2. Check alignment of pipes to the catalytic converter, secure bolts. 3. With everything in place, tack weld exhaust pipes to catalytic assembly. 4. Unbolt whole exhaust assembly from vehicle and let it hang. Complete weld around pipes. 5. Bolt assembly back in vehicle and check for clearance. 6. Re-install 02 sensors. Use anti-seize on threads of sensor. Route wires clear of exhaust system. 7. Lower vehicle to ground

Related Content:

2005 taurus exhaust system diagram, 2 2 s10 exhaust flange bolts, diagram of an exhaust system on a 2003 gmc envoy, Diagram of a exhaust crossover pipe for a 95 Oldsmobile aurora, 04 pacifica parts diagram, pontiac sunfire gt exhaust system diagram, how tight should exhaust, gmc yukon exhaust manifold diagram, 454 exhaust donut installation, 2006 corvette mid pipe flange torque

Related Content:

yhs-lavasoft, 2011 crv engine whine, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio, how to adjust the bands of an automatic trasmission of hyundai accent 2002