chevy malibu oil pressure switch problems

You search PDF repair manual about chevy malibu oil pressure switch problems, if there are search results will appear below. If search results do not exist, please search by others keyword.



  chevy malibu oil pressure switch problems Direct Download speed 5432 Kb/s

  chevy malibu oil pressure switch problems Full Version speed 8172 Kb/s



2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE MANUAL

0

Filed Under (Honda Manuals) by admin on 20-06-2012

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2 Fig. 16: Checking Continuity Between Rocker Arm Oil Pressure Switch 2P Connector Terminals Courtesy of AMERICAN HONDA MOTOR CO., INC. Is there continuity? YES- Go to step 9 . NO- Replace the rocker arm oil pressure switch (VTEC oil pressure switch) (see ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) REMOVAL/INSTALLATION ), then go to step 13 . 9. Turn the ignition switch ON (II). 10. Measure voltage between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminal No. 1 and body ground

Related Content:

solenoid 2007 honda, causes of low oil pump presure on 4l60e, 2008 gmc acadia radio no sound AND BACK POWER HATCH NOT WORKING, hazard switch wiring 2005 impala, written directions replace a/c actuator in 2011 Impala, replacing oil pressure switch on gmc sierra, 2007 CHEV UPLANDER LOW OIL PRESSURE, location of oil pressure switch 2005 Honda cr-v, 2005 mack cv713 dash, serviceing cooling system for lincoln ls

2003 Ford Excursion, F-Super Duty 250-550 Oil Filter Adapter Removal And Installation manual

0

Filed Under (Ford Manuals) by admin on 18-05-2012

download
Removal 1. Remove the LH engine mount. For additional 6. Disconnect the oil pressure switch electrical information, refer to Engine Mounts in this connector. section. 2. Drain the engine cooling system. For additional information, refer to Section 303-03. 3. Disconnect the coolant hoses. 7. Remove the oil pressure switch. 4. Remove the oil filter. 5. Remove the threaded insert and the oil cooler. 8. Disconnect the lower radiator hose. 2. Connect the lower radiator hose. 9. Remove the nut, the bolts, the oil filter adapter and the gasket. •Discard the gasket. 3. Install the oil pressure switch. 10. Clean the gasket surface at the cylinder block. Installation 1. Position the oil filter adapter gasket and the oil filter adapter. Install the nut and bolts. 4. Connect the oil pressure switch electrical connector. 7. Connect the coolant hoses. 5. NOTE: Make sure the tab on the oil filter adapter nests into the notch in the oil cooler. Position the oil cooler on the oil filter adapter and install the threaded insert. 8. Install the LH engine mount. For additional information, refer to Engine Mounts in this section. 9. Fill the engine with clean engine oil. 10. Fill and bleed the cooling system. For 6. Install a new oil filter. additional information, refer to Section 303-03

Ford Excursion Oil Filter Adapter Removal and Installation Manual

0

Filed Under (Ford Manuals) by admin on 05-02-2012

download
Removal 1. Remove the LH engine mount. For additional 6. Disconnect the oil pressure switch electrical information, refer to Engine Mounts in this connector. section. 2. Drain the engine cooling system. For additional information, refer to Section 303-03. 3. Disconnect the coolant hoses. 7. Remove the oil pressure switch. 4. Remove the oil filter. 5. Remove the threaded insert and the oil cooler 8. Disconnect the lower radiator hose. 2. Connect the lower radiator hose. 9. Remove the nut, the bolts, the oil filter adapter and the gasket. •Discard the gasket. 3. Install the oil pressure switch. 10. Clean the gasket surface at the cylinder block. Installation 1. Position the oil filter adapter gasket and the oil filter adapter. Install the nut and bolts IN-VEHICLE REPAIR (Continued) 4. Connect the oil pressure switch electrical connector. 7. Connect the coolant hoses. 5. NOTE: Make sure the tab on the oil filter adapter nests into the notch in the oil cooler. Position the oil cooler on the oil filter adapter and install the threaded insert. 8. Install the LH engine mount. For additional information, refer to Engine Mounts in this section. 9. Fill the engine with clean engine oil. 10. Fill and bleed the cooling system. For 6. Install a new oil filter. additional information, refer to Section 303-03

1995 Toyota 4Runner STARTING AND CHARGING SYSTEMS REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TROUBLE SHOOTING NOTE: See TROUBLE SHOOTING – BASIC PROCEDURES article in GENERAL INFORMATION. 1) If a no-start condition exists and battery is known to be good, connect test light or voltmeter between starter solenoid terminal No. 50 and ground. See Figs. 6 and 7. 2) Turn ignition switch to START position. If test light or voltmeter does not indicate voltage, check main fusible links and large ampere main fuses in engine compartment relay box. If fusible links and fuses are okay, see IGNITION SWITCH CONTINUITY TEST and/or STARTER RELAY TEST under ON-VEHICLE TESTING. ON-VEHICLE TESTING NOTE: Before testing, ensure battery is fully charged, battery cables and terminal ends are tight and clean, and engine grounds are secure. CLUTCH START SWITCH TEST 1) Switch is located above clutch pedal on bracket. Disconnect wiring harness connector from switch. 2) Connect ohmmeter probes to switch terminals. Depress clutch pedal. If continuity does not exist, adjust or replace clutch start switch. If continuity exists, check circuit to starter relay for open, and check starter relay. See STARTER RELAY TEST. CLUTCH START CANCEL SWITCH TEST 1) Locate switch in left dash panel. Remove right lower instrument panel to access switch connector. Disconnect wiring harness connector from switch pigtail connector. See Fig. 1. 2) Connect negative lead of ohmmeter to terminal No. 1. Ensure continuity does not exist between connector terminals No. 1 and 2, terminals No. 1 and 3, and terminals No. 2 and 3. Check operation of switch by connecting jumper wires from 12-volt battery. Connect positive lead to terminal No. 3 and negative battery lead to terminal No. 1. 3) Using ohmmeter, ensure continuity does not exist between connector terminals No. 1 and 2 until switch button is pushed. When switch button is pushed, switch light should come on and continuity should exist. Disconnect battery and ensure continuity does not exit between terminals No. 1 and 2. If switch does not test as specified, replace switch. Fig. 1: Identifying Clutch Start Cancel Switch Connector Terminals Courtesy of Toyota Motor Sales, U.S.A., Inc. IGNITION SWITCH CONTINUITY TEST WARNING: Deactivate air bag system before performing any service operation. For 1996 4Runner, see AIR BAG RESTRAINT SYSTEM article. 1995 1) Disconnect negative battery cable. Removedriver’s lower instrument panel cover. Remove upper and lower steering column covers if needed. Locate ignition switch wiring harness 8-pin connector. See Figs. 2-3. 2) With ignition switch in LOCK position, there should be no continuity between any terminals. With ignition switch in ACC position, there should be continuity between terminals No. 2 and 3. With ignition switch in ON position, there should be continuity between terminals No. 1, 2 and 3, and between terminals No. 7 and 8. 3) With ignition switch in START position, there should be continuity between terminals No. 1, 4 and 6, and between terminals No. 7 and 8. If continuity is not as specified, replace switch.

Related Content:

how do i install ignition switch on 1996 chevy pickup, how to replace a 1990 Toyota Corolla Ignition switch, g6 testing key switch, 2007 chevy silverado brake switch installation, what causes 2005 toyota sienna starter relay to burn out, how toremuve thh ignition key on chrysler 2002 concord LX1 or baypass, ignition switch removal on 2003 buick century, ignition switch wiring diagram 2006 chevrolet uplander, no power between starter and ignition uplander, relay system in a 2002 buick centry

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

0

Filed Under (Audi Manuals) by admin on 01-07-2012

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

Related Content:

Oil Pan Gasket Leaking 2005 altima, 07 kia sportage oil pan removeing, how to change oil pan gasket 2003 chevy silverado 5 3, instutins how to replce oil PAN GASKEET ON 2006 CHEV IMPLA 5 3, ntc cummins pan bolts, oil drain pan torque 1991 corrola, oil drain plug for 3406e cat, oil pan for a 03 pontiac aztek, oildipsticktuberemoval 6 4litreford, on manual transmission how to seperate the motor from transmission

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

0

Filed Under (Chevrolet Manuals) by admin on 22-05-2012

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Related Content:

replace oil cooker 3406 cat motor, 2006 impala oil filter housing gasket, removing the oil pan on a 2008 impala 3 5, 2006 chevy trailblazer engine removal, oil cooler on 3406 cat how to change, 2012 kia srento a/c condensor drain line drawing, 2005 ford escape 2 3liter oil dipstick housing seal, oil flow path for 5 3 chevrolet, clips for blazer oil cooling lines, how many man hours to replace engine suburban 2007 for

2008 Ford F-Super Duty LACKS POWER, LEAKS FLUID FROM EXHAUST PIPE, ABNORMAL TAILPIPE SEDIMENT, WHITE SMOKE, EXHAUST SMELL, AND MIL ON SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 02-02-2012

download
ACTION To diagnose and correct the concern, refer to the following Service Procedure. SERVICE PROCEDURE NOTE DO NOT START ENGINE Evaluation, Inspections, And Checks 1. Retrieve KOEO diagnostic trouble codes (DTCs). 2. Check oil level. Remove and clean dipstick. Reinsert into dipstick tube only until dipstick handle reaches top of dipstick tube (Figure 1). NOTE FIGURE 1 DEMONSTRATES DIPSTICK Figure 1 – Article 07-8-9 POSITIONING FOR OVER-FULL CHECK. KEEP 3. Check coolant level. DIPSTICK HANDLE OFFSET OF CENTER TO PREVENT IT FROM FULLY SEATING. IF OIL 4. Check fuel quality. LEVEL IS BELOW THE MAX MARK, OIL IS NOT OVER-FULL. 5. Inspect tailpipes for abnormal sediment; for example black soot, white ash, oil, coolant, or fuel. 6. Inspect vehicle for coolant, oil and fuel leaks at the following locations: •Tailpipes Repair Directions •Section A – If the following DTCs are present P0087, P2291, P0263-0284, P0300-P0308, or P1336 or if observation of external fuel leaks, for example, wetness around exhaust manifolds or over-full oil level indication. •Section B – If the following DTCs are present P132B, P2262, or P2263 or observation of oil leaks (aside from over-full oil level) or oil level is low. Figure 2 – Article 07-8-9 •Section C – If coolant low or observation of 8. Replace any leaking components and verify coolant leaks. leak has been repaired while running IDS high •Sections A, B, and C – If only abnormal sediment pressure fuel system test – KOER. in tailpipes. 9. Perform WSM, Section 303-04D – Turbocharger SECTION – A Bearing Clearance Check. Fuel System Diagnostics 10. If fuel quality is poor, drain all fuel and replace with known good ultra-low sulfur diesel fuel. NOTE IN CASES WHERE ENGINE OIL HAS BEEN 11. If no DTCs were stored in pending or DILUTED WITH DIESEL FUEL AND ALL REPAIRS continuous memory go to Step 13. ARE COMPLETE, RELEASE THE OIL FILTER CAP 12. Is there abnormal sediment in tailpipes or fuel ALLOWING OIL TO DRAIN TO OIL PAN AND evident? KEEP FILTER, DRAIN THE OIL FROM OIL PAN AND FILL WITH NEW OIL. TIGHTEN OIL FILTER a. No – Complete PC/ED worksheet and CAP AND RUN ENGINE FOR 10 MINUTES. applicable PPT tests for the codes retrieved. FINALLY, CHANGE OIL FILTER AND OIL AGAIN. b. Yes – Go to Step 13. 1. If oil is not over-full – go to Step 9. 13. Is there abnormal sediment in the tailpipes?

Related Content:

ford 2014 c max service manual

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra, silverado motor mount replace

2000 Pontiac Bonneville V6-3.8L VIN K – A/T 4T65E Harsh Shifts/Shudders/Slips Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 13-07-2012

download
Line Pressure Check Procedure Tools Required Important: Before performing a line pressure check, verify that the pressure control (PC) solenoid valve is receiving the correct electrical signal from the PCM. Caution: Keep the brakes applied at all times in order to prevent unexpected vehicle motion. Personal injury may result it the vehicle moves unexpectedly. J 21867Universal Pressure Gauge Set 1. Install a Scan Tool. 2. Start the engine and set the parking brake. 3. Check for a stored Diagnostic Trouble Code (DTC). 4. Repair the vehicle, if necessary. 5. Check the fluid level. Refer to the Transmission Fluid Checking Procedure. 6. Check the manual linkage for proper adjustment. 7. Turn the engine OFF. Remove the oil pressure test hole plug and install the J 21867. 8. Put the gear selector in PARK range and set the parking brake. 9. Start the engine and allow the engine to warm up at idle Notice: Total test running time should not be longer than two minutes, or else transmission damage could occur. Notice: Refer to Fastener Notice in Cautions and Notices. Parts Information 10. Access the PC solenoid valve control test on the Scan Tool. Zoom Sized for Print 11. Increase the PC solenoid as shown actual current from 0.0 to 1.0 amps in 0.1 amp increments. Allow the pressure to stabilize for five seconds after each pressure change. Read the corresponding line pressure on the J 21867. 12. Refer to the Line Pressure specification table. Compare the data to the table. 13. If pressure readings differ greatly from the table, refer to Incorrect Line Pressure. 14. Remove the J 21867. 15. Apply sealant, P/N 12345382 (in Canada, P/N 10953489), to the oil pressure test hole plug. 16. Install the oil pressure test hole plug. Tighten Tighten the oil pressure test hole plug to 12 N.m (106 lb in).

Related Content:

bad purge valve solenoid symptoms, PCM 40i Manual, 2011 cruze purge valve, shift solinoid 4t65e-n, pcv valve chevy cruze, p30 proportioning valve, mazda 3 p0758, how to change the evaporative purge valvo on a sonoma, gm dtc po597, 2001 tahoe sunroof seal

OIL PAN ADAPTER INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
Remove the oil pan prior to installing the oil pan adapter. Refer to a factory service manual for your vehicle for reference. 2. The Oil Drain Adapter requires the oil pan to be drilled. The hole should be located above the oil level in the pan in an area that does not interfere with any other parts and that will allow oil to flow freely from the drain hose. Mark the area to be drilled. We find that typically, locating the center drain hole 1.5″from the Oil Pan Rail, provides clearance between the adapter fitting and the pan rail, and also keeps the drain hole above the oil level in the pan (See Fig. 1) . Using a scratch awl, mark the center of each bolt hole 9/16″away from the center of the center drain hole so the distance from center to center is 1.125″ (See Fig. 1) . 3. Using a center punch, indent each drilling location to prevent the drill bit from walking. Pre-drill each hole with a 1/8″bit. Secure the oil pan on a work bench or on a drill press, and drill the outer bolt holes to ¼”. Drill the center drain hole to ½”. Deburr the holes and thoroughly clean the oil pan to remove any metal shavings. 4. Install the Oil Drain Adapter onto the oil pan using the two of the ¼-20 bolts, ( Note: Select the appropriate length bolt for your application. If you have a cast aluminum oil pan, you will typically use the 5/8″long bolts; if you have a stamped steel oil pan, you will typically use the 1/2″long bolts. We recommend using blue Loctite on the threads.) and the two ¼” Stato-Seal washers on the inside of the oil pan, using the gasket on the outside of the pan (See Fig. 2a & 2b). Torque the bolts to 6-8 ft/lbs. 5. Re-install the oil pan. Refer to a factory service manual for your vehicle for reference.

Related Content:

Dodge 46rh convertor drain

Related Content:

solenoid 2007 honda, causes of low oil pump presure on 4l60e, 2008 gmc acadia radio no sound AND BACK POWER HATCH NOT WORKING, hazard switch wiring 2005 impala, written directions replace a/c actuator in 2011 Impala, replacing oil pressure switch on gmc sierra, 2007 CHEV UPLANDER LOW OIL PRESSURE, location of oil pressure switch 2005 Honda cr-v, 2005 mack cv713 dash, serviceing cooling system for lincoln ls