Skip to content

2000 chevy s10 evaporator removal

You search PDF repair manual about 2000 chevy s10 evaporator removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000 Ford Crown Victoria/Grand Marquis Evaporator Core Housing Removal And Installation Manual

download
Evaporator Core Housing Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Recover the refrigerant. For additional information, refer to Section 412-00 . 3. Drain the radiator so that the coolant level is below the heater core. For additional information, refer to Section 303-03 . 4. Raise the vehicle. For additional information, refer to Section 100-02 . 5. Remove the RH front wheel and tire. 6. Remove the screws from the RH fender apron and remove the fender apron. 7. Remove the nuts. 8. Lower the vehicle. 9. Remove the blower motor switch resistor. For additional information, refer to Section 412-04 . 10. Disconnect the connector. 11. Disconnect the evaporator to compressor suction line from the suction accumulator drier. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 12. Disconnect the condenser to evaporator tube from the A/C evaporator core inlet tube. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 13. Remove the nuts and position the purge valve and backet away from the evaporator core housing. 14. Remove the heater hoses from the heater core. 15. Disengage the connectors fom the bracket. 16. Disconnect the connector. 17. Remove the nut and reposition the wire harness away from the evaporator housing. 8 18. Disengage the harness from the bracket. 19. Remove the pin-type retainer and clip and remove the instrument panel lower insulator. 20. Fold back the carpet and remove the screw. 21. Inside the vehicle, remove the screw. 22. Remove the nuts(engine side).

2000 Mitsubishi Truck Montero Sport Evaporator Core Removal and Installation Manual

download
EVAPORATOR REMOVAL AND INSTALLATION REMOVAL SERVICE POINT SUCTION PIPE OR HOSE, DISCHARGE PIPE DISCONNECTION CAUTION: Seal the hoses completely, otherwise the compressor oil and receiver will absorb water vapor easily, possibly damaging the condenser and deteriorating performance. Plug the disconnected hose and the evaporator nipple to prevent foreign material from getting into them. INSTALLATION SERVICE POINT >A< EVAPORATOR INSTALLATION When replacing the evaporator, refill it with the specified amount of compressor oil and install it (to the vehicle).

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

1996-2000 Honda Civic Door Panel REMOVAL And INSTALLATION Manual

download
Honda Door Panel 96-00 Civic REMOVAL & INSTALLATION Remove the screw from behind the interior door handle Slide out the door handle trim as shown Removing the door panel from the passenger side door View of the inside of the door, panel removed 1. Remove the screw from the door handle trim. 2. Slide the handle assembly forward and out to access the lock rod clip. 3. Release the clip 4. Disconnect the door lock switch 5. Remove the door opener handle assembly. 6. Carefully pry at the small opening on the bottom of the speaker grill. 7. Remove the speaker grille. 8. Remove the speaker mounting screws. 9. Detach the electrical connector and remove the speaker. 10. Remove the screws in the armrest. 11. Remove the center from the trim clip at the upper front of the door panel and remove the clip. 12. Using a suitable trim panel removal tool, unsnap the door panel from the door frame. 13. Carefully lift the door panel up and away from the door frame. To install: 14. Installation is the reverse of the removal procedure. Honda Civic/Del Sol 1996-2000 Electric Window Motor REMOVAL & INSTALLATION 1. Remove the regulator from the door assembly. 2. Except for the rear doors, drill a hole through the regulator sector gear and backplate. Install the bolt and nut to lock the sector gear in position. Be careful not to drill a hole closer than 7/ 16 in. (11mm) from the edge of the sector. Also, do not drill through the lift arm attaching portion of the sector gear, or the joint integrity will be jeopardized. 3. Drill out the ends of the motor attaching rivets using a 1/ 4 in. (6mm) bit. 4. Remove the motor and the remaining portions of the rivets from the regulator. Except for the rear doors, one rivet will not be accessible until assembly. Regulator and motor assembly—except rear doors Secure the rivets by collapsing the rivet ends using a ball peen hammer To install: 5. Position the new motor to the regulator. With the aid of an assistant, install new rivets by collapsing or crushing the rivet ends using a ball peen hammer. 6. Except for the rear doors, once two of the three rivets have been installed, remove the bolt securing the sector gear to the backplate, then use an appropriate electrical source (such as the vehicle’s window motor harness) to rotate the regulator, providing access to the remaining rivet. 7. Except for the rear doors, use a flat nosed rotary file to grind off one sector gear tooth from the side which does not contact the driven gear. This is necessary to reach the remaining rivet. Remove the old rivet, then install the remaining new rivet. 8. Install the regulator to the door assembly.