fod f250 column shifter linkage diagram

You search PDF repair manual about fod f250 column shifter linkage diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  fod f250 column shifter linkage diagram Direct Download speed 5432 Kb/s

  fod f250 column shifter linkage diagram Full Version speed 8172 Kb/s



1997 Ford Thunderbird/ Cougar Steering Column Removal And Installation Manual

0

Filed Under (Acura Manuals) by admin on 12-04-2012

download
Steering Column Disassembly CAUTION: Do not remove the steering column, steering wheel and air bag module as an assembly from the vehicle unless the column is locked to prevent rotation, or lower end of steering shaft is wired in such a way to prevent the steering wheel from being rotated, as this will damage the air bag sliding contact. 1. Disconnect battery ground cable (14301). Refer to Section 14-01 . 2. Remove steering wheel (3600) as described. 3. Remove steering column from vehicle as described. 4. Remove steering column lower yoke (3N725), steering column upper bearing spring (3520), suspension height sensor control ring (3C131) and steering column bearing tolerance ring (3L539). Lower Steering Column Assembly 5. Remove turn indicator cancel cam (13318) by pushing up with flat-bladed screwdriver. Note direction of flush surface. 6. Remove ignition switch (11572) assembly. 7. Remove bearing retainer (3C610) and steering column upper bearing spring. . Remove steel steering column bearing tolerance ring and steering column bearing sleeve (3518). 9. Remove plastic bearing retainer from ignition switch lock cylinder bore. 10. Remove metal steering column lock housing bearing (3E700) from ignition switch lock cylinder bore. 11. Note position of steering column lock gear (3E717) to actuator lock. Remove steering column lock gear. 12. Remove two pivot bolts. Use caution becausesteering column position spring (3D655) will release when bolts are removed. Remove steering column lock cylinder housing (3511). 13. Remove steering column shaft assembly from steering column. 14. Remove steering column lock lever actuator (3E715) and steering actuator housing (3F723). 15. Remove lower steering column bearing (3517) and steering column lower bearing retainer (3D681).

Related Content:

mgb steering shaft removal, 2005 chevy s-10 streeing colum repair, 2008 ford 150 wiring harness box under steering colum, 1993 chevrolet suburban steering column diagram, 1994 chevy s10 steering column wiring, silverado steering column diagram 2005, install steering Center Link on 1989 s10, how to replace shiftetr cloum on 2002 ford f 150, how to remove the steering wheel cover from 04 pontiac grand prix, How to Remove Steering Column volvo vnl

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

0

Filed Under (More Manuals) by admin on 05-05-2012

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, replace shifting cable for 2003 GMC Envoy how do you remove the console, buick rendezvous gear shift cable repair, replace shifter handle on 2000 malibu, 2006 cobalt shifter micro switch pin, chevy cobalt shift lock, cover push button on shifter for chevey 2007 cobalt automatic, How to replace shift indicator on 99 f150, how to change a cable on gmc envoy

1989 Toyota 4Runner STEERING COLUMN REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 13-11-2011

download
REMOVAL & INSTALLATION STEERING COLUMN Removal 1) Disconnect battery ground cable. Remove steering wheel. On Cressida, Corolla, MR2 and Tercel models, remove fuse box cover, lower instrument trim panel and air duct from under steering column. 2) On all models, remove upper and lower steering column covers. Remove combination switch. Mark position of “U” joints and shaft for reassembly. 3) On models with “U” joints, remove “U” joint retaining bolt. On models with flexible joint, remove flexible joint retaining bolt. NOTE: On 2WD Pickup models, remove steering column with intermediate shaft attached. 4) On all models, mark position of joint and pinion shaft for reassembly. Remove intermediate steering shaft. 5) Remove floor pan cover bolts. Remove tilt bracket-to- dashboard mounting bolts. Remove steering column toward inside of vehicle. Fig. 1: Exploded View of Camry, Corolla, MR2 & Tercel Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Celica, Cressida & Supra Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 3: Exploded View of Land Cruiser, Pickup, Van & 4Runner Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Installation 1) To install steering columns, reverse disassembly procedure. Grease main steering shaft and all bearings. 2) Ensure marks made to flexible couplings and to “U” joints are aligned. Ensure steering column and shafts do not bind after installation. STEERING COLUMN OVERHAUL NOTE: Camry, Corolla, MR2 and Tercel steering columns are similar. Some of the following procedures will not pertain to all models. Disassembly (Camry, Corolla, MR2 & Tercel) 1) Remove tension springs, grommets and screws from tilt bracket. Remove tilt lever left-hand set bolt. Remove column upper support lock bolt. 2) Remove tilt steering support bolts and pawl set bolts. Place bushings and “O” rings aside and keep them clean. Remove ignition lock cylinder. 3) Using a screwdriver, push 2 thrust stoppers into bearing retainers. Pull out shaft from column. Remove the No. 1 column ring, bearing retainer, thrust stoppers and No. 2 column ring from shaft. 4) Remove snap ring and lower bearing from shaft. Remove bearing inner snap ring. Remove upper bracket retaining bolts and ground strap. Separate upper bracket from column. Inspection 1) Check that steering lock mechanism operates properly. Check upper bearing for smooth rotation or excessive noise. Replace upper bearing (if necessary). 2) Using Drift (09631-00020) and Adapter (09627-30010), drive bearing from upper bracket. Pack new bearing with grease. Using the same drift and adapter used in removal, drive new bearing into upper bracket. 3) Inspect lower bearing for smooth rotation or excessive noise. If lower bearing shows signs of wear or damage, replace with a new one. Reassembly 1) Install upper bracket onto column. Install ground strap. Tighten retaining bolts to 14 ft. lbs. (19 N.m). Install inner snap ring on shaft groove nearest to center of shaft. 2) Install lower bearing and lower bearing snap ring. Place No. 2 column ring into position next to bearing on side nearest center of shaft. See Fig. 4.

Related Content:

2003 toyota camry 2 4 main crankshaftbearing removal, stearing colium cover removel 2003 buick reagel, Reinstall steering column for 1992 Toyota Camry, kia sorento front drive shaft center bearing removal, kia sorento center support bearing removal, kia sorento 2007 manual driveshaft carrier bearing, jeep upper bearing pulls out, how to remove steering column cover on 1994 mitsubishi gt3000, does the center bearing on a 2007sorento require lubrication, 2007 kia sorento center support bearing

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix, igt savp parts diagram

Ford F-Series Column Shift Repairs Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
It’s a simple system. To remove the assembly, start by removing the column shift lever. This is super easy; just use two small punches to depress the two spring-loaded pivot pins on the lever, then pull the lever out. Be aware: the pivot pins and spring will shoot out. Next go under the hood, and undo the two bolts holding the clamp piece just above the steering box. The lower half of the clamp will come free. The upper half is locked to the “shoe” plate under it, and to the steering column, with a round peg cast into it. So you need to pry the shoe up away from the steering column to get the peg clear of the column. Once you do that, you need to pry the upper half of the clamp away from the shoe, so the peg is clear of the shoe. Once it is clear, you can slide the end piece off the shifter tube. Then slide the wave washer and 2-3 lever off. To get the 1-R lever off, you’ll need to pull a steel pin out of the shifter tube. It should just drop out. Then slide the lever, wave washer, and shoe off the tube. Push the shifter tube up to get the clearance needed for the shoe. The shifter tube is a hollow steel tube, with a hole drilled thru it near the bottom. In this hole there is a steel pin (the one just removed). The steel pin engages into slots in the 1-2 and 3-4 levers, to move them. As you can see, there isn’t a lot of wear in my shift levers’ slots. The pin shows some wear, where the tube contacts it. The pin is hardened steel and the shifter tube is mild steel, so the tube will be worse than the pin. The pins are available from Obsolete Ford Parts and others, P/N 01A-7337, only a couple of bucks. Getting the shifter tube out is pretty easy; just drop the column support (remove the bolts to instrument panel and loosen the pinch bolt) down to the floor, and you’ll be able to swing the shift tube to the side to clear the steering wheel, and pull it out. My pin wasn’t that worn, it’s the hole in the tube. The tube is hollow but actually has a steel plug inside it with a hole for the pin. It is pushed inside the tube and then peened in two places thru the outer tube (they punched the outer tube to lock the inner plug). inner plug had gotten loose inside the tube, too. If this is your situation, you could just drill and pin the plug to the outer tube, and get a good improvement. I wanted “like new”, so I took my shifter tube to my favorite machinist (Gene at Noor Mfg. in Albuquerque, a super guy). He made up a whole new lower end for the tube out of 1018 carbon steel. It’s got a spigot on the upper end that was pressed into the remaining tube, welded, then turned down. It is better than new! Look at the difference in the shape of the hole. Price for the work was very reasonable

Related Content:

how do you replace an altenator on a 2005 honda pilot youtube, FREE INSTRUCTIONS ON SHIFTER TUBE REPLACMENT 2001 FORD F 150 /COLUMN SHIFTER, removing a 2000ford f250 shift tube, 96 windstar shifter tube clamp holder, 2005 chrysler town and country evaporatordraintube, where is the orifuce tobe on 1998 chevy silverado, yhs-jomedia, p01626, kia sedona ac drain hose clogged, how to installand adjust console shift handle 1999 ford taurus

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 02-01-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

iS THERE A SPRING CONNECTING THE LINKAGE TO THE TPS ON A97 LESABRE, edelbrock dubble carburetor adjustment linkage, relearn on throttle body trailblazer 2005, throttle body for a 2006 buick rendezvous, relearn procedure for throttle body 2004 chevy trailblazer, volvo penta throttle control diagram, p1512 chevy trailblazer, where is the fuel line to throttle body on a 2006 KIA RIO, lincoln ls throttle linkage, jaguar s type throttle body return spring

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

4g13 engine ignition adjustments, carter duel quad carb adjustment, Duromax 7 hp idle adjustment, how to change kancil carburetor, schematic diagram of elect fuel system include locations for a 1989 toyota camry 2 0 engine passenger car, setting caburater kancil, specialist kancil carburetor, volvo penta 3 0 glpj valve adjustment

1997 Ford Thunderbird/Cougar Steering Column with Air Bag

0

Filed Under (Ford Manuals) by admin on 21-05-2011

download
Steering Column with Air Bag The steering column has a steering wheel (3600) which is bolted to the top of the steering column and is fitted with a supplemental air bag system. * Before performing work on or around any supplemental air bag system component, observe all supplemental air bag system conditions and warnings to avoid accidental air bag deployment and possible injury. * Refer to Section 01-20B for supplemental air bag system conditions and warnings. Steering Column, Tilt — Disassembled View Section 11-04: Steering Column 1997 Thunderbird/Cougar Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 05/16/2000 Item Part Number Description 1 043B13 Driver Side Air Bag Module 2 N804385-S100 Steering Wheel Bolt 3 3600 Steering Wheel 4 N805572-S36 Air Bag Module Retaining Screws (2 Req’d) 5 3L518 Steering Wheel Spoke Cover (2 Req’d) 6 N804385-S100 Screw 7 14A664 Air Bag Sliding Contact 8 13318 Turn Indicator Cancel Cam 9 3C610 Bearing Retainer 10 3520 Steering Column Upper Bearing Spring 11 3518 Steering Column Bearing Sleeve (Upper) 12 3517 Steering Column Bearing (Upper)(Small) 13 3517 Steering Column Bearing (Large) 14 3524 Steering Gear Input Worm Gear and Rack 15 390345-S36 Screw 16 13K359 Multi-Function Switch

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE SERVICE MANUAL

0

Filed Under (Toyota Manuals) by admin on 25-01-2012

download
Repair Procedure 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. Production Change Information Parts Information Repair Procedure STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 3 of 4 3. Remove the No. 2 steering intermediate shaft assembly. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 7. Install the No. 1 steering column hole cover sub-assembly onto the steering gear with a NEW clamp. Repair Procedure (Continued) B A a No. 2 Steering Intermediate Shaft Intermediate Shaft STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 4 of 4 8. Install the No. 1 steering column hole cover sub-assembly by attaching clip B onto the body and installing the No. 1 hole cover onto the body with clip A. NOTE: Make sure that the lip of the No. 1 hole cover is NOT damaged. 9. Install the No. 2 steering intermediate shaft assembly. A. Align the matchmarks (“a”) on steering intermediate shaft and the steering sliding yoke and temporarily install them with bolt B. Torque: 35 Nm (360 kgfcm, 26 ftlbf) B. Ensure the wheels are straight. C. Install the No. 2 intermediate shaft and the intermediate shaft with bolt A. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 10. Install the column hole cover silencer sheet. A. Install the column hole cover plate with the 2 clips. B. Install the floor carpet. 11. Remove the steering wheel holder from the vehicle. 12. Road test the vehicle to verify the repair and confirm that the steering wheel is centered.

Related Content:

07 ford escape intermediate drive shaftpassenger side, 2003-2011 ford crown vic intermediate steering shaft removal, 3024 CAT Rocker Shaft Assembly, 91 Dakota Intermediate Steering Shaft, 92 Dakota Intermediate Steering Shaft, cruze cam cover crack, steering pitman shaft drawing 91 dodge dakota 2 wheel drive

1992 Ford Taurus V6 Dashboard / Instrument Panel Service and Repair Removal and Installation

0

Filed Under (Ford Manuals) by admin on 08-06-2011

download
Removal and Installation 1. Position front wheels in the straight ahead position. 2. Disconnect positive battery cable. 3. Remove cluster finish panel, please refer to Body and Frame/Interior Trim/Dash Board/Service and Repair/ See 4. Disconnect all electrical connections from steering column switches. 5. Remove two bolts and reinforcement from under steering column. 6. Disengage insulator retainer and remove insulator. 7. Remove four nuts and absorber assembly from under steering column. CAUTION: Do not rotate steering column shaft. 8. Disconnect park brake release cable and wiring connector from park brake and ignition switch wiring connector. 9. Remove four nuts retaining steering column to support, disconnect PRNDL cable (column shift) and lower column on front seat. Cover front seat to protect from damage. 10. Install lock cylinder to ensure that steering column shaft does not turn. 11. Remove four retaining screws from cluster, disconnect wiring and remove. 12. Remove one bolt at steering column opening attaching instrument panel to brace 13. Remove one instrument panel brace retaining bolt (under the radio area). 14. Remove sound insulator under glove compartment by removing two pushnuts that secure insulator to studs on climate control case. 15. Remove three screws attaching glove compartment assembly to instrument panel and remove door assembly. 16. Remove air cleaner, battery and battery tray.

Related Content:

2008 ford taurus repair manual download, how to remove steeringwheel on 2003 taruas

Related Content:

mgb steering shaft removal, 2005 chevy s-10 streeing colum repair, 2008 ford 150 wiring harness box under steering colum, 1993 chevrolet suburban steering column diagram, 1994 chevy s10 steering column wiring, silverado steering column diagram 2005, install steering Center Link on 1989 s10, how to replace shiftetr cloum on 2002 ford f 150, how to remove the steering wheel cover from 04 pontiac grand prix, How to Remove Steering Column volvo vnl