2000 ford expedition rear axle oil amount

You search PDF repair manual about 2000 ford expedition rear axle oil amount, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2000 ford expedition rear axle oil amount Direct Download speed 5432 Kb/s

  2000 ford expedition rear axle oil amount Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Torque specs for 2008 prius axle nuts, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, replace shaft seal in AT 2006 Avalon, rearaxleremovamodelaford, remove front diff bearing in navagator, remove rear axle on a 02 mustang

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

0

Filed Under (Audi Manuals) by admin on 01-07-2012

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

Related Content:

04 2 7l allroad p0491 p0492, cummins isx subassembly procedure, Oil Pan Gasket Leaking 2005 altima, replacing oil pan 2000 avalon, instutins how to replce oil PAN GASKEET ON 2006 CHEV IMPLA 5 3, mack mp8 coolant pump replacement, torque specs for 2004 chevy deisel oil pan, ntc cummins pan bolts, oil drain pan torque 1991 corrola, oil drain plug for 3406e cat

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE MANUAL

0

Filed Under (Honda Manuals) by admin on 20-06-2012

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2 Fig. 16: Checking Continuity Between Rocker Arm Oil Pressure Switch 2P Connector Terminals Courtesy of AMERICAN HONDA MOTOR CO., INC. Is there continuity? YES- Go to step 9 . NO- Replace the rocker arm oil pressure switch (VTEC oil pressure switch) (see ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) REMOVAL/INSTALLATION ), then go to step 13 . 9. Turn the ignition switch ON (II). 10. Measure voltage between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminal No. 1 and body ground

Related Content:

solenoid 2007 honda, saturn ion shift handle micro switch, causes of low oil pump presure on 4l60e, injection actuation pressure sensor no c7 cat, cruse control for 1996 toyota tocoma how to change switch, crv honda 2004 vtech oil pressure switch, location of oil pressure switch 2005 Honda cr-v, rev issue on 40l60e, dt466e hard start no start diagnostics pdf, dt466 injection control pressure

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

0

Filed Under (Chevrolet Manuals) by admin on 22-05-2012

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Related Content:

replace oil cooker 3406 cat motor, 2006 impala oil filter housing gasket, 2006 chevy trailblazer engine removal, removing the oil pan on a 2008 impala 3 5, oil cooler on 3406 cat how to change, 2001 a4 oil cooler lines, 2012 kia srento a/c condensor drain line drawing, how to install oil filter adapter gasket 2007 montana, 2005 ford escape 2 3liter oil dipstick housing seal, how many man hours to replace engine suburban 2007 for

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

2000 Ford F-Super Duty 250-550/ Excursion/ F-53 Motorhome Chassis Workshop Manua

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
Removal 1. Set the parking brake. 2. Loosen the retaining bolts. 3. Raise the vehicle to the desired working height, keeping the axle parallel with the floor; for additional information, refer to Section 100-02 . 4. Release the parking brake. 5. Remove the wheel(s); for additional information, refer to Section 204-04 . 6. Remove the brake caliper and rotor on the single rear wheel axle; for additional information, refer to Section 206-04 . 7. Remove the retaining bolts and axle shaft. 9. d the hub nut if es apart during removal. no circumstances e operations. NOTE: The hub nut will ratchet during this operation. Remove the hub nut (counterclockwise for right-hand thread; clockwise for left-hand thread). 10. Install the Step Plate. 11. Install the 2-Jaw Puller and loosen the rear hub to the point of removal. 12. hub bearing when b. Remove the rear hub assembly. 3. l a new hub seal ub assembly is removed. NOTE: The inner bearing is located behind the hub seal. Pack each bearing and replace the hub seals; for additional information, refer to Bearings, Cups and Seals in this section. 14. treme care not to scratch or gouge the seal or bearing surfaces. If after hub removal, the hub seal or seal inner sleeve remains on the spindle, remove it as shown using the Step Plate and the 2-Jaw Puller. 15. Inspect the seal surface and inner shoulder for scratches and damage. ? Remove all scratches, gouges or galling damage with #600 or finer crocus cloth. Installation 1. NOTE: Clean the spindle thoroughly after removing the rear hub. Coat the spindle with axle lubricant. 2. b bearings must be prelubed prior to installation. Fill the hub cavity with 29.6 ml (1 oz) of SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A. 3. treme care not to damage the hub g it to contact the spindle during installation. NOTE: Coat the spindle and hub seal inside diameter with SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL- M2C192-A. NOTE: Installing the rear hub in this manner causes the outer bearing to act as a pilot making the installation easier. Push the rear hub and outer bearing onto the spindle as an assembly. ? Hold the outer bearing seated and use the bearing as a pilot

Related Content:

how to change a rear wheel hub on 2009 nissan maxima, how to repair a wheel seal on a 2004 f250, how to replace wheel bearings on 2005 acura mdx diagram

2008 Ford F-Super Duty LACKS POWER, LEAKS FLUID FROM EXHAUST PIPE, ABNORMAL TAILPIPE SEDIMENT, WHITE SMOKE, EXHAUST SMELL, AND MIL ON SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 02-02-2012

download
ACTION To diagnose and correct the concern, refer to the following Service Procedure. SERVICE PROCEDURE NOTE DO NOT START ENGINE Evaluation, Inspections, And Checks 1. Retrieve KOEO diagnostic trouble codes (DTCs). 2. Check oil level. Remove and clean dipstick. Reinsert into dipstick tube only until dipstick handle reaches top of dipstick tube (Figure 1). NOTE FIGURE 1 DEMONSTRATES DIPSTICK Figure 1 – Article 07-8-9 POSITIONING FOR OVER-FULL CHECK. KEEP 3. Check coolant level. DIPSTICK HANDLE OFFSET OF CENTER TO PREVENT IT FROM FULLY SEATING. IF OIL 4. Check fuel quality. LEVEL IS BELOW THE MAX MARK, OIL IS NOT OVER-FULL. 5. Inspect tailpipes for abnormal sediment; for example black soot, white ash, oil, coolant, or fuel. 6. Inspect vehicle for coolant, oil and fuel leaks at the following locations: •Tailpipes Repair Directions •Section A – If the following DTCs are present P0087, P2291, P0263-0284, P0300-P0308, or P1336 or if observation of external fuel leaks, for example, wetness around exhaust manifolds or over-full oil level indication. •Section B – If the following DTCs are present P132B, P2262, or P2263 or observation of oil leaks (aside from over-full oil level) or oil level is low. Figure 2 – Article 07-8-9 •Section C – If coolant low or observation of 8. Replace any leaking components and verify coolant leaks. leak has been repaired while running IDS high •Sections A, B, and C – If only abnormal sediment pressure fuel system test – KOER. in tailpipes. 9. Perform WSM, Section 303-04D – Turbocharger SECTION – A Bearing Clearance Check. Fuel System Diagnostics 10. If fuel quality is poor, drain all fuel and replace with known good ultra-low sulfur diesel fuel. NOTE IN CASES WHERE ENGINE OIL HAS BEEN 11. If no DTCs were stored in pending or DILUTED WITH DIESEL FUEL AND ALL REPAIRS continuous memory go to Step 13. ARE COMPLETE, RELEASE THE OIL FILTER CAP 12. Is there abnormal sediment in tailpipes or fuel ALLOWING OIL TO DRAIN TO OIL PAN AND evident? KEEP FILTER, DRAIN THE OIL FROM OIL PAN AND FILL WITH NEW OIL. TIGHTEN OIL FILTER a. No – Complete PC/ED worksheet and CAP AND RUN ENGINE FOR 10 MINUTES. applicable PPT tests for the codes retrieved. FINALLY, CHANGE OIL FILTER AND OIL AGAIN. b. Yes – Go to Step 13. 1. If oil is not over-full – go to Step 9. 13. Is there abnormal sediment in the tailpipes?

Related Content:

ford 2014 c max service manual

2007 HONDA ODYSSEY SPLASH GUARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 14-10-2011

download
INSTALLATION NOTE: •These instructions show the left splash guards being installed. The same procedure applies to installing the right splash guards. •Clean and wax the areas to be covered with a high-quality paste wax. Installing the Front Splash Guards 1. Turn the steering wheel all the way counter clockwise to provide access to the left front fenderwell. 2. Remove the two self-tapping screws from the left front inner fender. PARTS LIST Right front splash guard Left front splash guard Right rear splash guard Left rear splash guard 6 Self-tapping screws 2 Spring nuts 2 Square head grommets 3. Using a pushpin, make a small hole through the center of the upper clip. UPPER CLIP PUSHPIN SELF-TAPPING SCREW LEFT FRONT INNER FENDER SPLASH GUARDS P/N 08P00-SHJ-101 2 of 2 All 33039-33598 (0608) LEFT REAR SPLASH GUARD SELF-TAPPING SCREW LEFT REAR FENDERWALL SELF- TAPPING SCREW (reused) REAR BUMPER LEFT REAR SPLASH GUARD There must be no clearance. REAR BUMPER LEFT FRONT INNER FENDER LEFT FRONT SPLASH GUARD LEFT FRONT INNER FENDER SELF- TAPPING SCREW LEFT FRONT SPLASH GUARD CLIP CLIP SELF- TAPPING SCREW SELF-TAPPING SCREW (reused) LOWER HOLE 5. While holding the left splash guard against the fender, tighten the self-tapping screws in the order shown. 6. Turn the steering wheel all the way clock wise and repeat steps 2 through 4 to install the right front splash guard. Installing the Rear Splash Guard 7. Using a floor jack, lift up the left rear side of the vehicle according to the service manual. 8. Remove the self-tapping screw from the rear bumper. Using a pushpin, make a hole through the center of the recess. 9. Install one square head grommet into the hole in the left rear fenderwall. Slide one spring nut over the hole you made in step 8 in the rear bumper. 10. Position the left rear splash guard on the left rear fenderwall and rear bumper, and loosely install one self-tapping screw you removed, and the two self-tapping screws supplied with the kit. LEFT REAR FENDERWALL REAR BUMPER SELF-TAPPING SCREW (Reuse.) SQUARE HEAD GROMMET SPRING NUT RECESS PUSHPIN REAR BUMPER With RECESS SELF- TAPPING SCREW 4. Install the left front splash guard using the two self-tapping screws removed in step 2, and one self-tapping screw supplied with the kit. Do not tighten the self-tapping screws yet. 11. Hold the left rear splash guard against the fenderwall and check that there is no clearance between the splash guard and rear bumper. Tighten the three self-tapping screws in the sequence shown. 12. Repeat steps 7 thru 11 to install the right rear splash guard

Related Content:

yhs-fullyhosted_003, how do you replace liftgate relay for 2005 escalade, rear hub assembly removal for 2008 toyota tundra, installation instructions for a 2007 honda accord front bumper, ruff and tuff golf cart parts rear axle bearing, rear cam seal 2000 monterro, Rear brakes 2000 Jag xj8 procedure, rear ac lines on 05 chevy trailblazer, lincoln ls rear suspension squeak, liftgate actuator replacement tahoe

1979-1985 Toyota Pick-Up 4WD Superlift 7″ Lift System for INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 24-03-2012

download
INSTALLATION PROCEDURE 1) FRONT OF VEHICLE… â Put the transmission in neutral. Position a floor jack under the front axle and raise vehicle. Place jack stands under the frame rails a few inches behind the spring’s rear shackles. Ease the jack down until the frame is resting in the stands. Keep a slight load on the jack. Put the vehicle in gear or park, set emergency brake and chock rear wheels to prevent any possibility of movement. ââ Remove tires and shocks. Remove the engine belly-pan to gain access to the anti-sway bar. Remove and discard the anti-sway bar assembly. Our spring/shock rate and the bars design render it useless. Reinstall belly-pan. ââ Detach the flexible rubber brake hoses at the calipers only and pinch closed with vise-grips to prevent fluid loss. SEE SEPERATE INSTRUCTIONS. You will install the Superlift hoses later. â Remove the stock drag-link. SEE SEPERATE INSTRUCTIONS. You will install the Superlift link and steering arm later. FORM #7047 .01-080707 PRINTED IN U.S.A. PAGE 2 OF 5 â Remove the bolt attaching the trac-bar (or torque rod) to its bracket on the drivers side of the axle. Unbolt the driveshaft at the front axle and tie it up and out of the way. ââ Remove the spring U-bolts. Ease down the front axle by lowering the jack. The axle vent hose may need rerouting of replacing. Install the Polyurethane bushings into the spring eyes. Lubricate all bushing wear surfaces with light grease. ââ Install the Superlift springs so that the thick end of the degree shims, attached to the bottom of the spring, are pointing towards the front of the vehicle. NOTE: There is a driver (DR) and passenger (PA) side spring. Start, but do not tighten the spring hanger/shackle bolts. ââ Raise the axle up to the springs. Be sure the spring center bolt heads seat properly in the axle perch holes. Attach with the new furnished U-bolts and evenly torque to 131ft. lbs. â Install the superlift Trac-Bar Bracket. â Install the Superlift steering Arm and Adjustable Drag- Link. ââ Install the front Superlift Extended Length Brake Hoses. ââ Install shocks, tires and lower vehicle. ââ With the vehicle weight on the suspension, tighten the front and rear spring hanger bolts. Do not over tighten; tighten only until the bushing flanges compress slightly. 2) REAR OF VEHICLE… NOTE: Before starting, with the vehicle weight on the suspension, rotate the position of the brake proportioning rod where it goes into the proportioning valve; which is located on the passenger side frame rail. On most vehicles, the rod is pretty much horizontal at the attaching point. After the lift is installed, re-bend the rod to its stock position at the proportioning valve. ââ Place a floor jack under the rear axle and raise vehicle. Place jack stands under the frame rails, a few inches in front of the rear springs front hangers. Ease the jack down until the frame is resting on the stands. Keep a slight load on the jack. Chock the front wheels to prevent any possibility of movement. Remove tires, U-bolts and shocks. ââ Disconnect the emergency brake cables at the rear wheels. Lower the axle housing by easing down the jack. Do not overextend the brake and axle vent hoses; both may need rerouting or replacing. If a Superlift rear hose is to be installed detach the stock rubber hose at the axle housing only and pinch closed with vise-grips to prevent fluid loss. You will install the new hose after installing the other rear components

Related Content:

2005 Toyota Avalon Rear Suspension Assembly no 2, wher to place jack stands on 2012 town and country

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Torque specs for 2008 prius axle nuts, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, replace shaft seal in AT 2006 Avalon, rearaxleremovamodelaford, remove front diff bearing in navagator, remove rear axle on a 02 mustang