Skip to content

2000 impala service manual free

You search PDF repair manual about 2000 impala service manual free, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

2000 Saturn SL2 L4-1.9L DOHC VIN 7 Body/ Electrical Service Manual

download
1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key. ^If the ignition key turns, proceed to step 30. ^If the ignition key does not turn replace the ignition module/passlock sensor by continuing with next step. 6. Disable SIR system. Refer to “Disabling Frontal Inflators” procedure in the 2000/2001 S-Series Body Electrical Volume II Service Manual

2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140 Repair Manual

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. Figure 1 SELF-DIAG RESULTS SYSTEM ENGINE DATE 03/15/2002 3:35:35 P/N 23710-7J400 DTC Code TP020169 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 2/3 ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 2000 M/T 23710-7J400, -7J401, -7J402, -7J460 2000 A/T 23710-7J410, -7J411, -7J412, 7J470 2001-2002 M/T 23710-6J105, -6J106, -6J107, -6J108, 6J170 2001-2002 A/T 23710-6J115, -6J116, -6J117, -6J118, -6J180 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Look in the “Vehicle” Column in Chart A (above) and determine the vehicle “configuration” (i.e. 2002 M/T). Make a note of the vehicle configuration and perform ECM Reprogramming , below. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Honda Navigation System Information and DVD Information and Inspection Manual

download
REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5