Skip to content

2000 saturn sl2 exhaust system parts

You search PDF repair manual about 2000 saturn sl2 exhaust system parts, if there are search results will appear below. If search results do not exist, please search by others keyword.

1996-2000 Chevrolet And GMC Suburban/ Pick-Up 2500/ 3500 Series TUBULAR EXHAUST SYSTEM INSTALLATION INSTRUCTION

download
Disassembly – Left Side 1. Disconnect negative cable from battery. 2. Use penetrating oil on all nuts and bolts to be removed. This will prevent the possibility of broken or stripped nuts and bolts. 3. Remove air cleaner system (note position of line and hose connections). 4. Disconnect spark plug wires. 5. Disconnect temperature sensor wire. 6. Remove EGR fitting. 7. Remove bolts and exhaust manifold. Disassembly – Right Side 1. Remove air cleaner box. 2. Disconnect spark plug wires. 3. Remove dipstick and dipstick tube. 4. Remove bolts and exhaust manifold. 5. Clean exhaust flange surfaces on both cylinder heads at this time. DISASSEMBLY – CROSSOVER PIPE 1. Raise vehicle and support with jackstands. 2. Disconnect and remove 02 sensors (2), being careful not to rupture or destroy the unit. WARNING: Do not clean this unit in any cleaning solvent and do not damage wire. 3. Between left and right side of the catalytic converter is a 3-bolt flange with gasket. From the front face of flange, measure out 15″ towards front of truck and cut stock exhaust pipes. Remove exhaust pipes from vehicle. NOTE: Before cutting pipes, measure the height of the converter from the bottom of the floor board for when you install new exhaust pipes you can maintain same distance. •ASSEMBLY – LEFT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer, and thick flat washer at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install left side T.E.S. manifold from bottom side 3. Install all bolts and washers and tighten. Use thick flat washers on slotted holes. 4. Reinstall spark plugs. 5. Replace original equipment spark plug ends on cylinders #3 and #5 with 60° connectors and boots provided in kit. 6. Re-connect spark plug wires on left side. 7. Re-install temperature sensor wire to temperature sensor. ASSEMBLY – RIGHT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer and thick flat washers at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install right side T.E.S. manifold from top side. Now install dipstick tube. 3. Install remaining bolts and lock washers. 4. Align all parts and tighten all right side bolts at this time. 5. Replace original equipment spark plug ends on cylinders #4, #6 and #8 with 60° connectors and boots provided in kit. 6. Re-connect right side spark plug wires. 7. To prevent contact with the hot T.E.S. tubing, use nylon tie wrap (supplied) to secure the heater hose to the a.c. dryer. 8. Re-install air cleaner box. CROSSOVER PIPE ASSEMBLY 1. With catalytic converters in their natural position, install and bolt exhaust extension pipes to header collectors using 3/8″ – 16″ x 2 1/2″ hex bolts, 3/8″ flat washers, 3/8″ lock washers and 3/8 hex nuts. Use the 3″ donut provided in kit. 2. Check alignment of pipes to the catalytic converter, secure bolts. 3. With everything in place, tack weld exhaust pipes to catalytic assembly. 4. Unbolt whole exhaust assembly from vehicle and let it hang. Complete weld around pipes. 5. Bolt assembly back in vehicle and check for clearance. 6. Re-install 02 sensors. Use anti-seize on threads of sensor. Route wires clear of exhaust system. 7. Lower vehicle to ground

2007-2009 Toyota FJ Cruiser Banks Monster Exhaust System Installation Manual

download
1. Before starting work, familiarize yourself with the installation procedure by reading all of the instructions. 2. The exploded view (Figure 2) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction. 3. Throughout this manual, the left side of the vehicle refers to the driver’s side, and the right side to the passenger’s side. 4. Disconnect the negative (ground) cable from the battery (or batteries, if there are two) before beginning work. 5. Route and tie wires and hoses a minimum of 6″ away from exhaust heat, moving parts and sharp edges. clearance of 8″ or more is recommended where possible. 6. When raising the vehicle, support it on properly weight-rated safety stands, ramps or a commercial hoist. Follow the manufacturer’s safety precautions. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the front wheels are centered squarely on the topsides; put the transmission in park; set the hand brake; and place blocks behind the rear wheels. Caution! Do not use floor jacks to support the vehicle while working under it. Do not raise the vehicle onto concrete blocks, masonry or any other item not intended specifically for this use. 7. During installation, keep the work area clean. Do not allow anything to be dropped into intake, exhaust, or lubrication system components while performing the installation, as foreign objects will cause immediate engine damage upon start-up. Tools Required: • 1? 2 ” and 3? 8 ” drive ratchets with standard and metric sockets and 1 ? 2 ” and 3? 8 ” drive extension • Standard and metric combination or open-end wrenches • Standard screwdriver • Clean shop towels or rags • Pry-bar Highly recommended tools and supplies: • Foot-pound torque wrench • Penetrating oil or light lubricant spray General Installation Practices 97083 v.2.0 3 Monster Exhaust SySTEM INSTallaTIoN 1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post. 2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground. CaUTIoN: Do NoT WoRK UNDER aNy VEHIClE SUPPoRTED oNly By a JaCK. SEVERE INJURy May RESUlT. 3. From under the vehicle remove the factory exhaust starting at the 2-bolt flange in front of the muffler. Remove the two (2) bolts, two (2) washers, and two (2) springs from the flange and retain for re-use. NOTE: Remove the factory gasket from the 2-bolt flange. The exhaust system will be hanging by the exhaust hanger pins. 4. Liberally apply an aerosol lubricant on all the hanger pins. Remove the exhaust system from the vehicle by removing each hanger pin from the rubber grommet. NOTE: Remove hanger pins from the front of the vehicle to the rear. 5. Drop the exhaust system to the floor and move out of the way. You will not be reusing any components from the exhaust system. 6. Install the Banks conical gasket onto the vehicle’s 2-bolt flange. 7. Install the hanger pin on the intermediate pipe into the corresponding rubber grommet. Install the Banks intermediate pipe onto the factory 2-bolt intermediate pipe outlet using the factory hardware. See Figure 1. When tightening the

2000-2004 Honda Insight IMA System Indicator On With IMA DTC 77 REPAIR PROCEDURE

download
PROBLEM The IMA system indicator comes on and IMA DTC 77 (P1447) (battery module deterioration) or DTC 78 (P1449) (battery module deterioration) is set. CORRECTIVE ACTION Replace the battery module. If needed, replace the motor control module (MCM), the battery condition monitor (BCM), or both INSPECTION PROCEDURE 1. Turn the ignition switch to LOCK (0). 2. Remove the cargo floor mat (see page 20-44 of the 2000-04 Insight Service Manual). (In ISIS, use the keyword FLOOR MAT , and select Interior Trim Removal/Installation – Cargo Area from the list.) 3. Remove the battery module switch cover (two bolts), then remove the locking cover from the switch. 4. Flip the battery module switch to OFF . Reinstall the locking cover. 5. Wait at least 5 minutes to let the capacitors in the system discharge. 6. Remove the right trunk shelf support (five clips and two bolts). 7. Remove the six mid-frame cover bolts. Remove the intelligent power unit (IPU) lid (17 bolts). 8. Measure the voltage at the junction board terminals. There should be 30 V or less . If you read more than 30 V , there is a problem in the circuit; do the DTC troubleshooting first. SWITCH COVER LOCKING COVER BOLTS LOCKING COVER BATTERY MODULE SWITCH IPU LID RIGHT TRUNK SHELF SUPPORT BOLTS (17) CLIPS CLIPS BOLTS ON JUNCTION BOARD TERMINALS REPAIR PROCEDURE 1. Remove the battery module from the vehicle (see page 12-113 of the service manual). (In ISIS, use the keyword BAT MOD , and select Battery Module Removal/Installation from the list.) 2. Remove the lifting tool from the battery module. 3. Remove the mounting bolts for the MCM and the BCM (eight total). Unplug the electrical connectors (five for the MCM and three for the BCM), then remove the modules. 4. Install the MCM and the BCM in the new battery module. Use the original MCM and BCM if no replacement was needed; otherwise, use the appropriate replacement parts. Torque the mounting bolts to 9.8 N·m (7.2 lb-ft) . 5. Install the lifting tool on the battery module. 6. With someone to help you, carefully lift the battery module into the vehicle, and set it down into position. Remove the lifting tool. 7. Plug in the connectors, and install the Y condenser harness. Then install the mounting bolts. Torque the bolts to 24 N·m (17 lb-ft) . 8. Install the battery module air duct. Torque the bolt to 9.8 N·m (7.2 lb-ft) . 9. Connect the high voltage cables to the junction board. Torque the bolts to 9.8 N·m (7.2 lb-ft) . 10. Install the front and rear IPU braces and the mid- frame. Torque the bolts to 9.8 N·m (7.2 lb-ft) . Model Year MCM Part Number Replacement Part Number M/T Models 2000-01 1K000-PHM-000 thru 1K000-PHM-050 1K000-PHM-060 (H/C 7071525)

2005 Toyota 4Runner Exhaust System Installation

download
Original Exhaust System Removal Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble. 1. For an easier time during the removal of your original exhaust system, remove the spare tire from the vehicle as recommended by vehicle manufacturer. 2. Unbolt the flange shown in figure 1 located just in front of the rear muffler assembly. 3. Lubricate all the hangers and rubber isolators. 4. Using a muffler stand or an additional person to hold the rear muffler assembly up in place, remove the hanger from the rubber isolator and then remove the rear muffler assembly as shown in figure 2. 5. Unbolt the flange shown in figure 3 located just behind the catalytic converter. 6. Using a muffler stand or an additional person to hold the front muffler assembly up in place, remove the hangers from the rubber isolators and then remove the front muffler assembly as shown in figure 4. Installation 1. Place the muffler assembly into position as shown in figure 5 installing the hangers into the rubber isolators. Secure the flange using the original hardware. 2. Using the hardware provided, install both left and right hanger/bracket assemblies on the frame rails of the vehicle, just behind each rear tire as shown in figure 6. Install the rubber isolators provided onto the hanger/bracket assem- blies. 3. Place a clamp over the expanded end of the right tail pipe assembly and set it into position as shown in figure 7 installing the hanger into the rubber isolator. Do Not tighten the clamp. 4. Place a clamp over the expanded end of intermediate pipe and set it into position. Do Not tighten the clamp. 5. Place a clamp over the expanded end of the left tail pipe assembly and set it into position as shown in figure 8 installing the hanger into the rubber isolator. Do Not tighten the clamp. 6. Check your exhaust system for proper clearance under the vehicle and also for tip alignment. 7. Once position has been determined to be correct, tighten the Accuseal™ clamps to 32-35 ft. lbs. 9. Before starting your vehicle, make sure to check all wires, hoses, brake lines, body parts and tires for safe clearance from the exhaust system. 10. Start vehicle and check for any leaks. If any leaks are found, determine cause (such as loose or incorrectly positioned clamp) and repair as necessary.

2007 Toyota Camry LE/SE/XLE Exhaust System Installation Instructions

download
Borla Performance Rear Section Exhaust System Installation 1. Using the bolts provided and the original nuts, place the right muffler assembly into position as shown in figure 3 making sure to install the hangers into the rubber isolators. Hand tighten the hardware for now. 2. Using the original nuts, place the left muffler assembly into position as shown in figure 4 making sure to install the hangers into the rubber isolators. Hand tighten the hardware for now. 3. Check your exhaust system for proper clearance under the vehicle and also for tip alignment. 4. Once position has been determined to be correct, tighten the flange hardware to 22-25 ft. lbs. 5. Before starting your vehicle, make sure to check all wires, hoses, brake lines, body parts and tires for safe clearance from the exhaust system. 6. Start vehicle and check for any leaks. If any leaks are found, determine cause (such as loose hardware) and repair as necessary.