Skip to content

2000 silverado 1500 service manual

You search PDF repair manual about 2000 silverado 1500 service manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

2000 Saturn SL2 L4-1.9L DOHC VIN 7 Body/ Electrical Service Manual

download
1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key. ^If the ignition key turns, proceed to step 30. ^If the ignition key does not turn replace the ignition module/passlock sensor by continuing with next step. 6. Disable SIR system. Refer to “Disabling Frontal Inflators” procedure in the 2000/2001 S-Series Body Electrical Volume II Service Manual

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140 Repair Manual

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. Figure 1 SELF-DIAG RESULTS SYSTEM ENGINE DATE 03/15/2002 3:35:35 P/N 23710-7J400 DTC Code TP020169 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 2/3 ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 2000 M/T 23710-7J400, -7J401, -7J402, -7J460 2000 A/T 23710-7J410, -7J411, -7J412, 7J470 2001-2002 M/T 23710-6J105, -6J106, -6J107, -6J108, 6J170 2001-2002 A/T 23710-6J115, -6J116, -6J117, -6J118, -6J180 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Look in the “Vehicle” Column in Chart A (above) and determine the vehicle “configuration” (i.e. 2002 M/T). Make a note of the vehicle configuration and perform ECM Reprogramming , below. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following: