HARSH SHIFT AND/ORM.I.L. “ON”DTCP 0750, P0755, P0758, AND/ORP1760 –TC 002-06 Revised March3,2006 Page 2of3 PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 89661–42650 1 89661–42651 89661–42653 1 89661–42652 1 89661–42660 1 89661–42661 89661–42663 Engine Control Module (ECM) 1 89661–42662 Engine Control Module (ECM) 1 89661–42810 89661–42811 1 89661–42820 89661–42821 1 89661–42880 Same 1 89661–42890 Same 1 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Toyota Diagnostic Tester Kit* NOTE: SAll components from this kit/set are required S12 MegabyteDiagnostic Tester Program Card (P/N 01002593–005) with version 13.3aSoftware (or later) is required TOY220036 1 9 *Essential SSTs. **Referstodrawer number in SST Storage System. NOTE: Additional Diagnostic Tester Kits, Program Cards, or other SST smaybeorderedby callingSPX/OTC at 1-800-933-8335. 1. If the vehicle is currently exhibiting a harsh shift condition and/or M.I.L. “ON”with DTCP0750, P0753, P0755, P0758, and/or P1760 stored, refer to the Technical Information System (TIS), 2001–2003 model year RAV4 Repair Manual: S4WD: Diagnostics/Automatic Transaxle (U140f): Problem Symptoms Table S2WD: Diagnostics/Automatic Transaxle (U142E): Problem Symptoms Table NOTE: In some instances the vehicle must be operated at least 30 minutes before the condition can be duplicated. 2. If the vehicle exhibits the above condition, replace the ECM (PCM). Parts Information Required SSTs
repair and service manual covers Toyota Corolla, all US and Canadian models, 2003-2005. (Note: this manual does NOT include information specific to XRS models).
Table of Contents
Introduction: About this manual | Introduction | Vehicle identification numbers | Maintenance techniques, tools and working facilities | Buying parts | Jacking and towing | Booster battery (jump) starting | Conversion factors | Automotive chemicals and lubricants | Safety first! | Troubleshooting
TOYOTA TACOMA MY 2005- SUPERCHARGER FIT KIT Procedure Page 5 of 46 pages Issue: E 11/04/08 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). • The TIS Repair Manual can be referenced for additional details. Please see your Toyota dealer for a copy of this document. 1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 7, save this coolant as it will be reused. CAUTION: To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause the hot engine coolant and steam to blow out from the radiator. (h) All parts that are removed and not reused should be saved for the customer, i.e., “discard” means to save for the customer.
inspection and Pre-Installation Check Remove the parts from their packaging and carefully check that the kit contains all the parts listed on the delivery document. Familiarize yourself with each part and learn where it goes. Keep the parts clean at all times. WARNING A SIBS® unit must not be contaminated with any external matter that may adversely affect its operation and reliability Suggestions: • Inspect each brake and supplied items against the packing list included in the shipment. • Ensure all items are included as described. • Ensure all components remain in their original packaging until required for assembly. • Thoroughly read the Service Manual. Familiarize yourself with the tools required and prepare them for use; familiarize yourself with the parts of the brake and the process required for fitting each brake and control system. • Ensure complete cleanliness of all brake components and the working environment around the vehicle. • Ensure no contamination of the brake assemblies occurs during installation. • Follow the points in the manual as described; if you are not sure – check the Manual. • Place each brake close to the vehicle adjacent to the axle where the brake is to be fitted, ensuring that they cannot by contaminated by any foreign material. Preparation Make sure all the tools, equipment and brake components are readily available. Before starting installation, check that: 1. the battery is disconnected 2. the vehicle is standing safely on a hoist 3. the original Toyota brakes have been removed (refer to Toyota manual): a. remove rear axle shaft assemblies b. if fitting fronts, remove the front steering knuckle assemblies 4. the handbrake cable and lever have been removed 5. the required amount of SIBS® fluid is available 6. an empty drain pan is available
ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.