Skip to content

2001 buick park avenue blend door location

You search PDF repair manual about 2001 buick park avenue blend door location, if there are search results will appear below. If search results do not exist, please search by others keyword.

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

2001 Toyota Highlander Sport Utility, Radio, FRONT DOOR SPEAKER INSTALLATION MANUAL

download
2001 Toyota Highlander Sport Utility PRELIMINARY: Disconnect the negative battery cable. ANTENNA: The factory antenna is located atop the right front fender panel. RADIO REMOVAL AND IN-DASH INSTALLATION: Note: The factory radio provision is for a Double ISO/DIN style radio. An installation kit is required when installing an aftermarket stereo. 1. Using panel removal tool carefully pry off radio bezel. 2. Extract (6) 10 mm bolts securing radio and climate controls in dash, disconnect and remove. 3. Extract (8) Iso screws securing radio to bracket. 4. Extract (2) Philips screws securing bracket to bezel, pull away and remove radio. FRONT DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 1 ½” tweeter and a 6 ½” 3-Hole speaker mounted to a factory speaker adapter. 1. Remove screw cover from door opener cup and exract (1) Philips head screw, pry bezel out then forward to remove. 2. Remove inside mirror cover. 3. Pry out door cup and extract (1) Philips screw from beneath. 4. Exract (1) plastic fastener from front top portion of door. 5. Pry off door panel, pull away, disconnect, and remove. 6. Extract (3) 10 mm bolts securing speaker, pull away, disconnect, and remove. REAR DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 5 ¼” 3-Hole speaker mounted in a factory speaker adapter. 1. Remove screw cover from door opener cup and extract (1) Philips head screw, pry bezel out then forward to remove. 2. Pry out door cup and extract (1) Philips screw from beneath. 3. Pry off door panel, pull away, disconnect and remove. 4. Extract (3) 10 mm bolts securing speaker , pull away, disconnect, and remove

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

2001 – 2006 TOYOTA Sequoia BACK DOOR POWER WINDOW INOPERATIVE

download
BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 2 of 6 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Plastic Pry Tool Set* NOTE: All components from this kit/set are required 00002-06000-01 1 21 *Essential SSTs. **Refers to drawer number in SST Storage System. NOTE: Additional SSTs may be ordered by calling SPX/OTC at 1-800-933-8335. 1. Disconnect the negative (-) terminal of the vehicle battery. NOTE: Any time the negative (-) battery terminal has been disconnected, systems requiring initialization will need to be re-initialized after the negative (-) battery terminal has been reconnected. 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. Required SSTs Repair Procedure : 5 Clips : 3 Clips BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 3 of 6 5. Remove the strap cover, bolt, and pull strap. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9. 9. For 2005 – 2006 model year Sequoia vehicles ONLY: Remove the multiplex network door ECU. Using a drill of less than 3.2 mm (0.126 in.), drill out the two (2) rivet heads. HINT: Gently and vertically put the drill to the rivets and cut the rivet flanges. CAUTION: Take care as the cut rivets may be HOT. 10. For 2005 – 2006 model year Sequoia vehicles ONLY: Install the replacement multiplex network door ECU and rivets