chevy lumina coolant light stays fluid

You search PDF repair manual about chevy lumina coolant light stays fluid, if there are search results will appear below. If search results do not exist, please search by others keyword.



  chevy lumina coolant light stays fluid Direct Download speed 5432 Kb/s

  chevy lumina coolant light stays fluid Full Version speed 8172 Kb/s



1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

0

Filed Under (Saturn Manuals) by admin on 19-05-2012

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, crank sensor location on 6 7 power stroke, 2001 saturn fluid light comes on, Replace 2011 buick regal ambient temp sensor, 2002 rendezvous radiator repair

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, Low coolant light olds intrigue, how to check radiator fluid level pontiac grand prix, replace low coolent sencor on 1997 chevy lumnia, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 99 buick park avenue radiator installation, 2002 mercury sable cooling system, Low Coolant Sensor Location in olsdmobile silluette, evap sensor on 2002 suburban

2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

Related Content:

2000 Nissan sentra 1 8 engine bolt torque diagram, TOYOTA SO5D SERVICE MUNAL, what causes damage to a flywheel on a 2004 yukon, 2002 ford ranger 2 3 coolant diagram, TOYOTA SO5D SERVICE MANUAL, 2004 pontiac grand prix cooling system diagram, 2005 chevy impala motor diagram, 6m70 service manual obd codes pdf, Position of sensors in mitsubishi 4m 51 engine, perodua engine overhall pdf

AUTOMATIC TRANSMISSION Checking Transmission Fluid Level and Condition

0

Filed Under (Honda Manuals) by admin on 25-05-2011

download
Checking fluid level and condition (color and odor) at regular intervals will provide early diagnosis information about the transmission. This information may be used to correct a condition that, if not detected early, could result
in major transmission repairs. IMPORTANT: When new, automatic transmission fluid is red in color. As the vehicle is driven, the transmission fluid will begin to look darker in color. The color may eventually appear light brown. A dark brown color with burnt odor may indicate excessive fluid deterioration and signal a need for fluid change. Fluid Level When adding or changing fluid, use only DEXRON ®-lll. Refer to Maintenance and Lubrication in General
Information section for maintenance information and servicing interval. CAUTION: DO NOT OVERFILL. Overfilling will cause foaming, loss of fluid, abnor- mal shifting and possible damage to the transmis-sion. 1. Park the vehicle on level ground and apply the parking brake firmly. 2. Check fluid level with engine running at idle. NOTE: Be sure that transmission fluid temperature is below 30°C (86°F). 3. Move the selector lever through all gear ranges. 4. Move the selector lever to “Park”. 5. Let engine idle for 3 minutes and open the overfill screw (1). 6. Add released ransmission fluid until it flows out over the overfill screw opening. 7. Let engine idle until a fluid temperature etween 32° C (90°F) and 57°C (135°F) is reached, then close the overfill screw (1). Torque: 38 N*m (28 Ib ft) NOTE: Check transmission fluid temperature with scan tool.

2005-2008 Honda Odyssey Power Steering Pump Whines , Buzzes, or Hums Repair Manual

0

Filed Under (Honda Manuals) by admin on 16-05-2012

download
Inspect the power steering reservoir. Does one of the 3 ribs on the reservoir cover point toward the reservoir holder? Yes – This vehicle already has the revised power steering reservoir. Continue with normal troubleshooting procedures. No – Go to REPAIR PROCEDURE. REPAIR PROCEDURE 1. Drain the power steering reservoir: •Remove the reservoir from its holder. •Raise the reservoir, and disconnect its return hose. •Drain the reservoir fluid into a suitable container. Take care not to spill any fluid on the body or other parts. Wipe off any spilled fluid immediately. 2. Drain the fluid from the power steering system: •Connect a suitable diameter drain hose to the disconnected return hose. •Hold the end of the drain hose in a suitable container. •Start the engine, and run it at idle while you turn the steering wheel lock-to-lock several times. •When the fluid stops running out of the hose, shut off the engine. •Discard the used fluid. 3. Reinstall the return hose to the reservoir, then reattach the reservoir to its holder. Fill the reservoir to its upper level line with new power steering fluid. 4. Bleed the air from the power steering system: •Start the engine. •With the engine at a fast idle, turn the steering wheel lock-to-lock several times. 5. Check the condition of the fluid in the reservoir: •If the fluid looks contaminated, dark, or discolored, repeat steps 1 thru 5. •If the fluid is clear, go to step 6. 6. Place a suitable container under the vehicle to catch any fluid 7. Replace the power steering fluid reservoir: •Remove the reservoir from its holder. •Disconnect the return hose from the reservoir, and pour the fluid from the reservoir into a container. •Disconnect the outlet hose from the reservoir, and remove the reservoir. •Install a new reservoir in the reverse order of removal. •Fill the reservoir to its upper level line with new power steering fluid. 8. Start the engine, and run it at a fast idle. Turn the steering from lock-to-lock several times to bleed any air from the system. 9. Recheck the fluid level in the reservoir, and add more if needed. Do not fill the reservoir beyond its upper level line.

Related Content:

2011 cruze recall leaking radiator fluid, toyota dyna clutch fluid reservoir, washer fluid low silverado trucks

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2011 crv engine whine, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, automatic transmission adjustments for 1997 yuko, transmission module for 1999 ford ranger xlt, 2004 saturn Clutch Assembly Exploded View, 4r70w transmission rebuild manual download

Toyota Land Cruiser/ Lexus LX 470 Big Brake Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
Disconnect Stock Brake Line Disconnect Stock Brake Line Disconnect Stock Brake Line Disconnect Stock Brake Line Disconnect Stock Brake Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Note: All Photographs in This Manual Show Left Side Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. Installation Unless Noted Otherwise. After securing the vehicle at a convenient height, remove the front wheels. WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled br br br br brake fluid fr ake fluid fr ake fluid fr ake fluid fr ake fluid from any painted sur om any painted sur om any painted sur om any painted sur om any painted surfaces. faces. faces. faces. faces. Place a drip tray or several rags directly below the inboard brake line connection. If the area around the brake line connection to the chassis and strut is dirty, clean with brake cleaner or appropriate cleaning agent. Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or Note- Be sure the cap is securely installed on the master cylinder. If the cap is loose or removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. removed, it is likely more fluid will drip. Note: If you remove the bottom lug nut last while holding the bottom of the tire, it will lessen the chances of thewheel tilting on it’s own and make removal easier. Step 2 Step 2 Step 2 Step 2 Step 2 Step 1 Step 1 Step 1 Step 1

Related Content:

2014 tundra factory painted bumper

1993 Dodge Dakota FUSE PANEL IDENTIFICATION

0

Filed Under (Dodge Manuals) by admin on 24-05-2011

download
3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights. 9 – 15 Amp (Lt. Blue) Cigarette Lighter. 10 – 20 Amp (Yellow) Windshield Washers & Wipers. 11 – 20 Amp (Yellow) Turn Signals, Rear Wheel Anti-Lock Module. 12 – 10 Amp (Red) Radio. 13 – 4 Amp (Pink) Cluster Lights, A/C & Heater Controls, Cigarette Lighter Light & Ash Receiver Light, Radio Lights & Overdrive Switch Light. 14 – Not Used (1992-93); 15 Amp (Lt. Blue) (1994-95 Airbag Module, Speedometer, Gauges, Telltales. 15 – 2 Amp (Gray) Speed Control. 16 – 5 Amp (Tan) Gauges & Indicator Lights: Low Oil Light, Low Washer Light, Service Reminder Light, Transmission Oil Light, Brake Warning Light, Anti-Lock Brake Warning Light, Fuel Pacer Light, 4WD Indicator Light, Malfunction Indicator Light, Warning Buzzer, Overdrive Switch (1992-93); Transmission Oil Temperature Lamp, 4WD Lamp, Overdrive Module Seat Belt Warning Buzzer (1994-95). 17 – (Blank) Not Used. 18 – (Blank) Not Used. 19 – (Blank) Not Used. 20 – Not Used (1992-93); 25 Amp (Natural) (1994-95) Fog Lamps and Off Road Lamps. 21 – Turn Signal Flasher No additional definition. 22 – Time-Delay Relay No additional definition. 23 – Horn Relay No additional definition. 24 – Hazard Flasher No additional definition. 25 – Warning Buzzer

Related Content:

emission light on impala, 86 ford ranger emission sensors, 2011 dodge durango not charging, 1992 CHEVrolet silverado idle air control assembly calibration specifications, 1992 Grand Marquis Manual, mazda 3 transmission gear indicator light, service 4wd light on silverado, Isuzu NPR Warning Light Icons, slip light on nissan titan, how to reset washer fluid malibu 06

2000 Ford Ranger Cooling System Draining Filling and Bleeding Repair Manual

0

Filed Under (Ford Manuals) by admin on 10-07-2012

download
NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle, For additional information, refer to Section 100-02 . 3. Remove the lower radiator cover. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant such as VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants can degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, or brine, or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolants unless they meet the requirements of Ford specification ESE-M97B44-A or WSS-M97B51-A1. Not all coolant recycling processes meet these Ford specifications. Use of such coolants can harm the engine and cooling system components. All engines 1. Install the lower radiator cover.

Related Content:

2002 ford ranger cooling system diagram, WSS-M97B44-D and d2 different, m440 cooling system pdf, cooling system diagram for a 1999 ford expedition, cooling system in 2012 mazda 6, diagram of coolant system of a Ford 2008 Expedition, diagram of cooling system for a 2005 ford explorer, radkitplus1, FREE 2002 LINCOLN LS COOLING SYSTEM DIAGRAM, isuzu 3 2l cooling system diagram

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, crank sensor location on 6 7 power stroke, 2001 saturn fluid light comes on, Replace 2011 buick regal ambient temp sensor, 2002 rendezvous radiator repair